DYNOJET PC6-17085 POWER COMMANDER 6 2020-2022 Kawasaki Ninja Z H2 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
PC6-17085 POWER COMMANDER 6 2020-2022 Kawasaki Ninja Z H2
Installation Guide
Install guide for PC6-17085
Model coverage: 2020-2022 Kawasaki Ninja Z H2
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 VELCRO STRIPS
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 1 ALCOHOL SWAB
- 1 POSI-TAP
PLEASE READ ALL DIRECTIONS BEFORE STARTING THE INSTALLATION
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fly between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
set up you can alter your map based on gear position and setup gear-dependent
kill times when using a quick-shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
| 1. Remove both seats, the fuel tank, and the associated covers.
2. Lay the PC6 in the tail section and route the harness down the left side
of the frame going towards the engine.
3. Attach the ground wire of the PC6 to the engine ground terminal bolt
located on the rear left of the engine near the red, supercharger inlet.
---|---
| 4. Unplug the stock wiring harness from the throttle body sub-harness.
This is a GREY, 10-pin connector at the rear of the engine, attached to the
water hose fitting cover bolts. (The supercharger inlet is removed for
clarity)
| 5. Plug the PC6 in line with the stock wiring harness connectors.
6. Route the rest of the PC6 harness to the right side of the frame.
| 7. Unplug the throttle position sensor connector from the throttle body.
This connector is on the right side of the throttle body.
| 8. Using the supplied Positap attach the GREY wire from the PC6 to the
stock purple wire of the TPS harness.
9. Plug the TPS harness back onto the throttle body.
| 10. Unplug the stock crank position sensor connector.
This is a BLACK, 2-pin connector located on the right side of the
motorcycle near the ABS valve.
| 11. Connect the PC6 in line with the stock CPS and wiring harness.
| 12. Using the supplied Positap connect the BLUE/ WHT wire of the PC6 to the
GREEN/RED wire of the stock gear position sensor.
This is a BLACK, 3-pin connector on the left side of the engine. This step
does not need to be done if you do not plan on making any adjustments
dependent on gear position.
| 13. Secure the PC6 in the tail section using the supplied velcro.
14. Reinstall the fuel tank, bodywork, and seat.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS,
NV 89081 – 800-992-4993
DYNOJET.COM
© 2018-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
2020-2021 Z H2
IPC6-17085.01
Documents / Resources
|
DYNOJET PC6-17085 POWER COMMANDER 6 2020-2022 Kawasaki Ninja Z
H2
[pdf] Installation Guide
PC6-17085 POWER COMMANDER 6 2020-2022 Kawasaki Ninja Z H2, PC6-17085, POWER
COMMANDER 6 2020-2022 Kawasaki Ninja Z H2, COMMANDER 6 2020-2022 Kawasaki
Ninja Z H2, Kawasaki Ninja Z H2, Ninja Z H2
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>