Many Bidets WL-GB05-4AD-US Bidet Toilet Seat Instruction Manual

Many Bidets WL-GB05-4AD-US Bidet Toilet Seat

Specifications:

• Model: WL-GB05-4AD-US, WL-GB05-5AD-US
• Functions: Seat heating, Water heating, Rear/front wash, Warm air drying, Auto lid open/close, Lid slow close, Auto flushing,  Smart Remote Control, Moving wash, H/C Massage, Enema Wash, Antibacterial seat, External filter, Energy saving

Product Information

• Important Safeguards:
  When using electrical products, especially when children are present, follow basic safety precautions. Read all instructions before using the bidet toilet seat. Ground the product properly to reduce the risk of electric shock.

• Functional Differences of Different Models:
  Check the model you purchased to confirm the available functions. The model and specifications can be found on the nameplate at the rear of the machine.

• Safety Precautions:
  Read the safety precautions to prevent hazards and property losses. Pay special attention to safety signs to avoid serious injury or death.

Product Usage Instructions

• Part Name :
  Refer to the manual for part names and locations before installation.

• Product Installation:
  Before starting installation work, read the manual carefully. Contact customer service for any installation or performance issues.

• Confirmation Before Use:
  Make sure to confirm the model and functions before using the bidet toilet seat.

• How to Use:
  Follow the instructions in the manual for using different functions like seat heating, water heating, wash options, air drying, lid operations, and more.

• Cleaning Procedure:
  Refer to the manual for cleaning instructions to maintain hygiene and performance.

• Not in Use for a Long Time:
  Follow the guidelines in the manual if the bidet toilet seat is not used for an extended period.

• Quick Judgment and Maintenance for the Trouble:
  Refer to the troubleshooting section in the manual for quick maintenance tips in case of issues.

FAQ :

• Q: What should I do if I encounter problems with installation?
  A: Contact customer service for assistance with installation or performance issues.

• Q: Can I reuse an old inlet hose with the product?
  A: No, please use the new hose assembly included with the product to ensure proper functioning.

Bidet Toilet Seat
Please read this manual carefully before use and keep it properly

• Model: WL-GB05-4AD-US WL-GB05-5AD-US
• Correct specifications depend on the actual model.
• All specifications are subject to change without prior notice.
• Before starting installation work, read the manual carefully.
• If you encounter any problems in installation or performance, please be sure to contact us.
• Our contact information is on the bottom page of the manual.
• There is a guarantee in this manual, so please keep it properly and take it out for reading when necessary.

IMPORTANT SAFEGUARDS

• When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

• READ ALL INSTRUCTIONS BEFORE USING

• GROUNDING INSTRUCTIONS

• This product should be grounded. In the event of an electrical short circuit,
  grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

• DANGER– Improper use of the grounding plug can result in a risk of electric shock.

• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.

• This product is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided — if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the connection should be made by qualified service personnel.

• CAUTION: Risk of property damage. If it is necessary to use an extension cord, a single cord may be used provided that the “Type” begins with “SJ”, the cord is a 12 gauge, grounded (12/3), is no longer than 25 feet (7.6 meters), and is plugged into a GFCI* electrical outlet. Promptly replace an extension cord that exhibits any sign of damage.

• DANGER– To reduce the risk of electrocution:

  1. Do not use while bathing.
  2. Do not place or store product where it can fall or be pulled into a tub or sink.
  3. Do not place in or drop into water or other liquid.
  4.  Do not reach for a product that has fallen into water. Unplug immediately.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons.

1.  Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3.  Never operate this product if it has a damaged cord or plug, if it is not working prop-erly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8.  Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.
10. Unplug this product before filling. Fill (reservoir) with water only unless otherwise specified by manufacturer. Do not overfill (or specify filling instructions).
    SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

• When using an electrical appliance, basic precautions should always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
• WARNING – To reduce the risk of fire, electric shock, or injury:
  1. Do not leave Appliance when plugged in. Unplug from outlet when not in use and before servicing.
  2. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
  3. Use only as described in this manual. Use only manufacturer’s recommended attachments.
  4. Do not use with damaged cord or plug. If Appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
  5. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run Appliance over cord. Keep cord away from heated surfaces.
  6. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  7. Do not handle plug or Appliance with wet hands.

SAVE THESE INSTRUCTIONS
Please use the new hose assembly included with the product. Do not reuse old inlet hose.

• WARNING: IF CONNECTION IS MADE TOA POTABLE WATER SYSTEM,  THE SYSTEM SHALL BE PROTECTED AGAINST BACKFLOW
• Functional differences of different models
• Please confirm the model you purchased first, and then check the corresponding function. The model and specification can be found on the nameplate at the rear of the machine. indicates that the function is available and the blank indicates that no such function.

SAFETY PRECAUTIONS

In order to prevent hazards and property losses caused by users and others, please read the safety precautions in detail to use this product correctly.

• The following information is related to safety, please pay special attention!
• The logo and its meaning are described below：
• Warning It means that if you ignore this sign and misoperate, you may cause serious injury or death.
• Caution It means that if this sign is ignored and mis-operated, personal injury or financial loss may be caused.

WARNING
Do not splash the product with water.

May cause fire or electric shock.
Reminder:

• Children, people with physical (intellectual) defects and lack of experience or common sense should be accompanied by special personnel when using this product.

• This product must be connected with cold water supply (water inlet temperature is 1-40 ℃), otherwise it may burn or machine failure.

• WARNING
  If you ignore this sign and operate incorrectly, it may cause danger!

• Check whether the power socket is grounded.

• This product must be well grounded and can only be connected to the special 120V, 60Hz, 10A circuit with grounding fault short circuit or grounding leakage protector.

• Remove the dust on the plug and completely insert the plug into the socket. Pull out the plug and clean it with a dry cloth.

• It is only suitable for AC voltage of 120V (60Hz).

• It is forbidden to use too much load on the same socket.

• May overheat or cause fire.

• Do not use loose sockets. May cause fire or electric shock.

• Do not plug/unplug the power plug when your hands are wet.

• May get electric shock hazard.

• Do not pour water or detergent on the body or power plug.

• May cause fire or electric shock.

WARNING
If you ignore this sign and operate incorrectly, it may cause danger!

• Do not pull the power plug or power cord at will.
• May cause fire or electric shock.
• Ensure that the product uses tap water, and do not use other water sources other than tap water that do not meet the sanitary standards.
• May cause skin infection.
• May cause machine failure.
• Please pull out the plug before cleaning the product.
• May get electric shock hazard.
• Do not disassemble or refit the product by yourself.
• May cause fire or electric shock.
• Do not put high temperature and inflammables near the product.
• May cause fire.
• Do not bend or twist the water hose.
• May be leaking.

WARNING
If you ignore this sign and operate incorrectly, it may cause danger!

• Do not place heavy objects on the seat ring or cover.
• May damage the product.
• Do not use the following items to clean this product. Benzene, paint thinner, decontamination powder, nylon brush, etc.
• May damage the product.
• Do not close the seat cover and seat ring with force.
• May damage the product.
• When replacing the power cord, observe the following:
• If the power cord is damaged, contact the retail store where you purchased this product or the nearby customer service center.
• Only authorized technicians can replace the power cord.

WARNING
Please follow the following guidelines

• Do not expose the product to direct sunlight. May causes discoloration, plastic corrosion and damage.
• Do not use DC or AC power supply with voltage not 120V.
• May cause product fault.
• When using the product, make sure you don’t lean against the cover.
• The cover may be damaged.
• Do not pour urine on the body and nozzle.

Part name

Parts

Product installation

• Size requirements of adapter cover
  • A. Distance from water tank to the front of toilet: 505-535mm.
  • B. Distance from mounting holes to the back edge of toilet bowl: ≤70mm.
  • C. Spacing between two mounting holes: 118-182mm.
  • D. Distance from mounting hole to water tank: ＞30mm.

Preparation before installation

• Before installing the smart toilet cover:

  1. Remove the existing toilet cover and close the water supply system of the toilet cover.
  2. Press the flush button to release the pressure from the water supply pipe.
  3. Place a container under the inlet valve to fill the excess water.
  4. Close the water inlet angle valve and disconnect the connection between the water inlet valve of the toilet cover and the water supply pipe.
     Caution: When determining the outlet position of the circuit, it is necessary to follow the local standards.

• Install circuit outlet :

  1. Before installation, please reserve a power socket within about 1m on the right side of the toilet.
  2. It is recommended to use waterproof socket instead of extension cord connection products.

• All ceramic body outline drawings in this manual are for demonstration only.

Install the fixing plate

1. Install the expansion rubber plug into the mounting hole of the ceramic body.
2. Place a fixing plate above the mounting hole of the ceramic body.
3. Thread the bolt into the long hole of the adjusting block.
4.  The adjusting block shall be placed in the groove of the fixed plate in parallel, use the installation cardboard to assist in positioning the retainer plate, and the adjusting block shall be locked on the fixing plate with bolts.
   Fixed plate antiskid gasket

Caution: For uneven ceramic, add about 2mm thick gasket at the rear end of the fixed plate.
Install the toilet lid

• Align the bottom of the toilet with vthe direction of the fixing plate, and let the toilet push in the direction of the arrow.
• When you hear the “click” sound, it indicates that it is installed in place.

Warm tip:
Tips for fixing plate installation: first tighten the fixing plate to 70%, install the toilet cover, adjust the position, then press and hold the push rod to remove the toilet cover, tighten the bolts of the fixing plate, and finally install the toilet cover.

Install external automatic flushing accessories
(Only for model WL-GB05-5AD-US)

1. Dimension confirmation before installation
2. Turn off the power and water.
3. Open the toilet tank cover.
4. Measure the outer diameter and height of the top of ceramic fittings. The diameter should be between 63 and 79 and the height should be above 18. Otherwise, this automatic flushing module is not applicable.
5. Select the clamp according to the measured outer diameter of the top of the fitting. When the outer diameter of the top of the fitting is from 63 to 72, select the small clamp collar. When the outer diameter of the top of the fitting is from 73 to 79, select the large clamp collar.
6. Clamp the selected clamp collar into the host along the track. When you hear a click, it means that it is installed in place.

Installation and fixation of flushing module

1. Insert the automatic flushing module into the top of the fittings as shown in the figure.
2. Make sure the push rod is aligned with the flush button. If the push rod cannot press the flush button, insert the push rod adjusting block into the push rod.
3. Tighten the butterfly screw to ensure reliable fixation.
4. Tighten 4 locking cross stitch screws.
5. Fix the power cord at the screw position with a tie and lead out the power cord (The wire should preferably pass through the groove on the top of the water tank, and some water tanks do not have this groove).
6. Turn on the water source, connect the power supply, and test the manual and automatic flushing functions.
7. Close the water tank cover and installation is complete.

Power on and water supply

The installation positions of water and electricity shall be set separately.
Connect the water supply
Connect the external water source with the water inlet with the equipped hose and filter screen.

CAUTION

• The plug shall be connected to an effectively grounded socket.
• Otherwise, electric shock may be caused in case of power failure or leakage.

Turn on electricity

1. Install 120V (more than 10A) socket at a position above 50cm from the ground.
2. The socket shall be installed where the water is not easy to splash.
3. Use a grounded socket.
4.  Insert the power plug of the product into the socket.

WARNING!
Please connect the power supply according to the product power supply requirements, otherwise it may cause product fault.

Remote control installation

Installation method I

1. Remove the EVA adhesive sticker on the back of the remote control guild and remote control holder.(as shown in Figure 1 and Figure 2).
2. Stick the remote control guide and remote control holder at the verified position.(as shown in Figure 3).
3. After the remote control guide and holder is installed, put the remote control on the holder as shown in the figure.(as shown in Figure 6)

Installation method II

1. Facing the fixing hole of the remote control guide and remote control holder, drill two expansion pipe holes with diameter of 6 on the wall and insert the expansion pipe. (as shown in Figure 4)
2. Install the remote control guide and remote control holder and fix it with screws.(as shown in Figure 5)
3. After the holder is installed, put the remote control on the base as shown in the figure.

Confirmation before use Open valve

Open the inlet valve to provide water for the whole machine.
Confirmation and commissioning

1. 1. Check power supply.
   Confirm that the power plug is plugged in tightly and the indicator light on the plug is on, indicating that the system has been powered on. If the indicator light is not on, you can press the “reset” button on the plug to power on. After power on, you can hear the “tick” sound of the system buzzer.

2. 2. Human-body seating sensor
   In the area shown in the figure, someone raises the seat sensing. The system function can be enabled only when the system senses that someone is seated.

3. Check basic functions
   When the human body seating sensing is on, press the function on the quick panel to start the corresponding function.

4. Check the drying function
   When the human body is seated in the conduction state, press the function on the quick panel to start the corresponding function.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.

How to use

Quick use of knob

• Seated
  Turn backward to start rear wash function, and turn again to reduce water pressure.

• Seated
  Turn forward to start the front wash function, and turn again to increase the water pressure.

•   Seated

  • Long press for 2 seconds to get into Enema Wash, rotate again to adjust water pressure.
  • In non washing state: Press once to start the drying mode.
  • In washing state, press once to stop the current mode, and press again to start the drying mode.

How to use the button

• Water temperature button: Short press the button to switch the water temperature to level1, level2, level3, off, and cycle in turn.
• Long press the button to switch the nozzle moving or fixed cleaning state when using the rear wash/front wash function .
• Seat temperature button: Short press the button to switch the seat temperature to level1, level2, level3, off, and cycle in turn.
• Long press the button to switch the nozzle possition to level1, level2, level3, level2, level1, and cycle in turn when using the rear wash/front wash function.

one is seated red in rear wash functionblue in front wash function.and flashes red when a fault occurs
Care Function| Seat Heating| Make people not feel cold
Lid Slow Close| The damping device is used to make the seat ring the lid flips smoothly and the noise is small
Decorative Light| Soft lighting
Safety Function| Overheating Protection| Thermal fuse to prevent the water temperature and seat temperature from being too high
Anti-scald System| After sitting for 15 minutes the seat temperature will be automatically adjusted to level 1.
Secondary| Control Knob| The knobs and buttons on the side of the toilet lid can be Function used when the remote control fails
Manual Flushing| Manual flushing during power outages
Clean Function| Troubleshooting| Sense abnormality and remind
Nozzle self-cleaning| The nozzle will be cleaned by strong water pressure before and after use
Nozzle cleaning| Clean the nozzle

How to use the control remote
The function of the remote controller shall be subject to the actual object. Remote for Model WL-GB05-5AD-US

Remote for Model WL-GB05-4AD-US

Stop| Press the stop button to end the running function such as “rear wash”, “front wash”, “air drying” and “enema wash”. Long press for 2 seconds to turn on/off of beeping sound.| (Some models without this function)
---|---|---
ront    ash|

• When the user is sitting on the seat, press the ront button, the female washing function will be started after a beeping and run for 90 seconds. If user leaves the seat during the function is running, the function will be stopped.
• Default to moving washing press again to turn into fixing position washing.

Rear Wash| When the user is sitting on the seat, press the Rear button, the rear washing function will be started after a beeping and run for 90 seconds. If user leaves the seat during the function is running, the function will be stopped. Default to moving washing press again to turn into fixing position washing.
Enema Wash| When the user is sitting on the seat, press  button, the washing function will be started after a beeping and run for 90 seconds. If user leaves the seat during the function is running, the function will be stopped.
H/C Massage| When the “rear wash” or “front wash” function is started, press the ‘H/C Massage’ button to start or stop this massage function, and the water temperature changes alternately at 32-38 ℃.
Water Temperature| Press the water temperature button to increase the water temperature in the “rear ” “front ”                           modes. It has three levels and stand-by mode. 3 level is the highest and stand-by mode means all the indicated lights are off.
Seat Temperature| Press the seat temperature button to change the temperature of the seat. The seat temperature has 3 levels and off mode. Level 3 is the highest and off mode means all the indicated lights are off.
Pressure| Press the Pressure button               to change the water pressure of “rear wash”
and “front wash” modes. The water pressure has three levels.
User 1| Press the user 1 button for 2 seconds to memorize the current water temperature, air temperature, seat temperature, nozzle position and water pressure. Press the user 1 button to use the memory setting.
User 2| Press the user2 button for 2 seconds to memorize the current water temperature, air temperature, seat temperature, nozzle position and water pressure. Press the user 2 button to use the memory setting.

Flush

| Press the “Flush” button to start flushing once. The time interval between reopening flushing function should be greater than 30 seconds. Long press for 2 seconds to turn on/off of auto-flushing function.
Dry| When the user is sitting on the seat, press the Dry button, the air drying function will be started after a beeping and run for 3 minutes. If the user leaves the seat during the function is running, the function will be stopped.
Air Temperature| Press the air temperature button to change the air outlet temperature in ” ry” mode. The outlet air temperature has 3 levels and off mode. level 3 is the
| highest and off mode means all the indicated lights are off.
Nozzle Position| Press the nozzle position button to move the nozzle forward in the “rear wash” “front wash” and “enema wash” modes. It has three levels from 1 to 3 indicated
| lights on. The nozzle moves forward for one level when press each time, and
| then returns to level 1 after level 3.
Nozzle Cleaning| WL-GB05-5AD-US: Long press “nozzle position” button for 2 seconds, and the nozzle will come out. Then the cleaning hole will spray water to clean the nozzle
| for 10 seconds. Press stop button to stop it when it is running.
| WL-GB05-4AD-US: Press “nozzle cleaning” button, and the nozzle will come out.
| Then the cleaning hole will spray water to clean the nozzle for 10 seconds. Press
| stop button to stop it when it is running.
Night light| Turn on or turn off the decorative light of the control knob.
Lid Open/close| Press the lid open/close button to open the toilet lid, and then press the button again to close it. Press for 3s to start or stop the auto lid open/close function.
Code Matching| Press and hold the “front wash” button on remote control for 3 seconds, and the three indicators on the remote control will flash red. At the same time, the machine is powered on, and the buzzer will make a long beeping to indicate that the code is successfully paired. Otherwise, repeat the above actions again.

Cleaning procedure

Product Cleaning

1. Power cut
   Unplug the power plug before cleaning the product body.

2. Nozzle Cleaning
   Press the “nozzle cleaning” button on the panel of the remote control, and the nozzle will automatically come out to facilitate the user to clean. Use a soft cloth or soft bristled toothbrush to dip into the kitchen and wipe the nozzle with detergent. You can also remove the nozzle for cleaning. The method is holding the spray lance in one hand (not shaking) and pull out the spray nozzle with the other hand, and the spray nozzle will be taken out. After cleaning, it can be installed back. Finally, press the “stop” button, and the spray lance will return automatically.
   Spray lance

3. Clean the external parts of the product
   Clean the product with a soft cloth and neutral detergent. Do not use hydrogen chloride cleaner, thinner, benzene, sandpaper, polishing machine, perfume and insecticide and other cleaning products.

4. Clean the filter screen
   When users feel that the water flow is less than normal during use, they can clean both ends of the filter screen with a brush. The product must be completely separated from the water supply hose during cleaning. If the product is connected to an external filter, please replace it regularly according to the water quality.

Not in use for long time
Drain and cut off the power supply

1. Pull the plug out.
2. Close the valve and stop supplying water to the system. Remove the water inlet hose from the water inlet valve and drain the water in the hose.
3. Press and hold the push rod in the direction of arrow 1,  and then horizontally remove the toilet in the opposite direction of the water tank (arrow 2).

CAUTION
When using the product again, please confirm and test run (refer to the part Product Installation).

Quick judgment and maintenance for the troubles

If you think there is a fault, please read the following items first and take measures. If the fault cannot be solved, please contact the purchase place, exclusive store or our customer service center.
Please unplug the power cord before maintenance.

CAUTION

• When the power cord is damaged, it shall be replaced by the manufacturer, after-sales service center or professional personnel (with qualification certificate) to avoid safety accidents.
• In case of water leakage, first rotate the handle of the inlet valve clockwise, close the valve and stop water supply.

Please confirm the following precautions before maintenance

Power
Function non-responding|

• Is there power outrage? Is there power in the power socket?
•  Is the main power turned on?

|

• Please wait until power is restored. Please turn on the power socket.
• Please turn on the main power.

Rear wash/Front wash/Enema wash
No water|

• Is water cut off?
• Is water valve closed?
• Did you not touch the sensing area?

|

• Please wait for water.
• Please open the water valve.
• Please sit on the sensing area.

Water pressure is decreasing|

• Is the warm water switch off or the water temperature setting is low?
• Is the filter or external filter clogged?

|

• Turn up the water pressure by control knob or remote control.
• Clean the filter; Change the external filter regularly

Water temperature is low| Is the warm water switch off or the water temperature setting is low?|  Adjust the water temperature by control button or remote control
Stop spraying water after 90s of washing|  Just a setting. Not a fault problem|  Use the washing functions again
Fault Problem| Checking| Solution
---|---|---
Water stop during washing| ●  Probably that the human body doesn’t touch the sensing area of the seat ring| Adjust sitting position to make suresitting on the sensing area

Seat Sensor

It activates the washing without being seated.| Is the seat be splashed with water or has a wet towel on it?|

• Please wipe the water off with dry towel;
• Please take the wet towel away.

Auto flush function

Auto flush is not activated|

• Auto flush module not installed or not installed correctly;
• Some models doesn’t have this function.

| Please install the auto flush module according to the instruction above.
Seat heating
Seat temperature is low| Is the warm seat switch off or the seat temperature setting is low?| Adjust the water temperature by control button or remote control;

Remote control

Remote control not responding|

• Is the battery on the remote control depleted?
• Is the battery installed incorrectly?
• Probably that the human body doesn’t touch the sensing area of the seat ring?

|

• Replacement battery.
• Please install the battery correctly.
• Adjust sitting position to make sure sitting on the sensing area.

Warm air drying
Air temperature is low| Is the air temp. setting low?|  Adjust the air temp. by remote control.
Function stops during drying| Normally it stops after 3 mins of drying|

•  Use this function again.
• Adjust sitting position to make sure sitting on the sensing area

Air drying is not activated| ● Probably that the human body doesn’t touch the sensing area of the seat ring| Adjust sitting position to make sure sitting on the sensing area

• Others

Dirt not cleaned

|

•  Is the water valve fully open?
• Is the water valve filter blocked?
• Water pressure too low when sharing water with bathroom.

|

•  Open the water valve
• Clean the filter

Water is dirty|  The external filter is used over 6 months.|  Replace a new filter
Water pipe connection leaking| Is the nut of the connecting pipe not tightened?|  Tighten it
If there is any abnormal situation other than the above table, please contact the seller.

Troubleshooting

Alert| Knob light alert| Buzzer| Fault description
Seat temp. sensor alert|  Flash red once| 1 beep| Sensor open or short circuit will alarm and stop seat heating
Air temp. sensor alert|  Flash red twice| 1 beep| Sensor open or short circuit will alarm and stop air drying
Water temperature sensor alarm|  Flash red three| 1 beep| The outlet water temperature is greater than 45 ℃. (After 3 subsequent alarms, it returns to normal if there is no abnormality)

Technical parameters

temperature is at the maximum level, the water pressure is 0.2MPa, the water pressure is at the maximum level, and 30 second s before the Rear wash operation).
Power line length| 1.2m
Warm water heating mode| Instant heating
Water temperature| The temperature adjustment range is about 30 ℃- 39 ℃
Safety device| Flow monitoring sensor, water temperature sensor, bimeta temperature control control switch, temperature fuse.
Air temperature| Adjustable temperature range (room temperature-55℃)
Drying heating power| 200W
Seat ring surface temperature| Adjustable temperature range (room temperature-40℃)
Seat ring heating power| 40W
Water supply pressure| 0.15MPa-0.75MPa
Environment temperature| 1-40℃
Product size| L505xW375xH93mm
Product net weight| 4.2kg| 4.4kg

The bar codes on our products and outer boxes are only for internal use, not for other purposes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>