IMI TA-Slider 750 Proportional Push Pull Actuator Owner’s Manual

IMI TA-Slider 750 Proportional Push Pull Actuator

Specifications

• Date: 21/08/2023
• Protocol: Modbus TCP
• Product Name: TA-Slider 750 Plus Modbus TCP, TA-Slider 1250 Plus Modbus TCP, TA-Slider 1600 Plus Modbus TCP
• Product Model Numbers: 322226-X421X, 322227-X421X, 322228-4221X
• Product Description: Digitally configurable proportional push-pull actuator – 750N, 1250N (discontinued from 01.09.2023), 1600N
• Firmware Revision (Modbus RTU): 1.3.0
• Address: 1* to 247
• IP Addressing: DHCP by default, settable with the HyTune app via the TA-Dongle
• TCP Port: 81 to 65535 (default: 502)
• Endianness (float): Big-endian

Product Usage Instructions

These registers are used for various settings and monitoring. Here are some key registers:

1. 1.  **Register 0 – InPos:** Input position [0-10000]

2. Register 1 – Relay 1: Activate/Deactivate relay 1 [0: Deactivated, 1: Activated]

FAQ

• Q: How do I change the IP Address of the device?
• A: The IP Address is set by default using DHCP. You can change it using the HyTune app via the TA-Dongle.
• Q: What is the default TCP port for communication?
• A: The default TCP port is 502, but it can be changed within the range of 81 to 65535.

General information

• Date: 21/08/2023
• Protocol: Modbus TCP
• Product Name: TA-Slider 750 Plus Modbus TCP
  • TA-Slider 1250 Plus Modbus TCP
  • TA-Slider 1600 Plus Modbus TCP
• Product Model Number: 322226-X421X, 322227-X421X, 322228-4221X
• Product Description: Digitally configurable proportional push-pull actuator – 750N
  • Digitally configurable proportional push-pull actuator – 1250N (discontinued from 01.09.2023)
  • Digitally configurable proportional push-pull actuator – 1600N
• Firmware Revision (Modbus RTU): 1.3.0
• Address: 1* to 247
• IP addressing: DHCP by default, settable with HyTune app via the TA-Dongle
• TCP port: 81 to 65535 (default: 502)
• Endianness (float): Big-endian

Default Value

Modbus holding registers

Register| Address| Data type| Access| Unit| Value Range| **Default| ****Description**
---|---|---|---|---|---|---|---
InPos| 0| Word| R/W| ym| [0-10000]| n.a| Input position
Relay 1)| 1| Word| R/W| n.a| 0: Deactivated

1: Activated

| 0| Activate/Deactivate relay 1, need relay function set to Bus

control (see App) 1)

Relay2 1)| 2| Word| R/W| n.a| 0: Deactivated

1: Activated

| 0| Activate/Deactivate relay 2, need relay function set to Bus

control (see App) 1)

ForceCalib| 3| Word| R/W| n.a| 0: Deactivated

1: Activated

| 0| Request forced calibration
BusBinaryInput| 4| Word| R/W| n.a| 0: Deactivated

1: Activated

| 0| Bus binary input, used to change stroke limitation, need an App

configuration

FlowUnit| 5| Word| R/W| n.a| 0: l/h

1: GPM

| 0| Flow unit
Flow| 8| Float| R| FlowUnit| [0.0, 3.4e+38]| 0| Interpolated flow value. For this function to be active it is necessary to set the valve type in the valve section on the

HyTune app.

MBSN| 10| 4

bytes

| R| n.a| [0-2^32]| n.a| Actuator identification number
CurrentPos| 12| Word| R| 1/10%| [0-10000]| 10000| The measured position expressed in the percentage of the currently applicable maximum position depending on register CurrentRegime
CalibStroke| 13| Word| R| µm| [0-25000] (TA-Slider 750/1250) [0-35000] (TA- Slider 1600)| n.a| Measured calibrated stroke, its value depends on the actuator type and on the mechanical pre-setting of the valve.
MotorStatus| 14| Word| R| n.a| 0: Stop

1: Retract

2: Extend

3: Calibration

4: Manual-override

5: Clogging

6: Error

| n.a| Motor status
CurrentTime| 15| Long| R| sec| [0-2^32]| 0| Number of seconds elapsed since the latest restart
Motor_OnTime| 17| Long| R| sec| [0-2^32]| 0| Total of seconds of running motor
Actuator_OnTime| 19| Long| R| sec| [0-2^32]| 0| Total of seconds of running actuator
Actuator_Distance| 21| Long| R| mm| [0-2^32]| 0| Distance travelled by the actuator spindle
BinaryInput| 23| Word| R| n.a.| 0: Deactivated

1: Activated

| 0| Status of binary input.
Relay 1)| 24| Word| R| n.a.| 0: Deactivated

1: Activated

| 0| Status of Relay. Used to verify writing register 1 or to know relay status in the case of another parametrisation.1)
Relay2 1)| 25|  | R| n.a.| 0: Deactivated

1: Activated

|  | Status of Relay2. Used to verify writing register 1 or to know relay status in the case of another parametrisation.1)
PowerType| 26| Word| R| n.a.| 0: None

1: AC/DC low voltage 2: AC high voltage

3: USB

| 1| Power type. For Modbus/BACnet, it should always be “AC/DC low voltage”
ControlCharacteristics| 27| Word| R| n.a.| 0: Linear

1: EQM

2: AntiEQM

| 0| Characteristic of the actuator. On an EQM valve, it is recommended to keep a linear actuator characteristic.
Speed| 28| Word| R| s/mm| [3, 16]| 3| Speed of the actuator
SignalSource| 29|  | R| n.a| 1: Volt

2: Current

3: 3pts

4: OnOff

5: BusCom

| 1| Signal source. The BusCom is only available for bus variants of TA- Slider. It is possible to work in hybrid mode,

i.e control source analog and data acquisition bus (this

should be done via configuration in the HyTune mobile application).

ValveName| 30| String| R| n.a| n.a| n.a| Valve name (Set by App, free text)
ObjectName| 43| String| R| n.a| n.a| n.a| Object Name(Set by App, free text)
---|---|---|---|---|---|---|---
Localisation| 56| String| R| n.a| n.a| n.a| Localisation (Set by App, free text)
CurErr| 74| Long| R| n.a.| None = 0x00, PowerFailure = 0x01 Clogging = 0x02, StrokeDetectionFailure = 0x04, CyclicTime = 0x08, SignalOutOfRange = 0x10, OutputLineBreak = 0x20, InputLineBreak = 0x40, ResetToFactoryDefault = 0x80, SoftwareDBAccess = 0x2000, SoftwareError = 0x4000,

MotorControllerError = 0x8000, ClearError = 0x80000000

| 0| Current error status
Errors [10]| 76| Long| R| n.a.| [0-2^32]| n.a| Time in second (see current Time) reset to 0 when

actuator restart

78| Long| R| n.a.| CurErr| n.a| Current Error see error description above, cleared when

A clear error flag is set

80| Long| R| n.a.| [0-2^32]| n.a| Value (if exist data for error)
…|  | R|  |  |  | keep up to 10 errors
130| Long| R| n.a.| [0-2^32]| n.a| Time in second (see current Time) reset to 0 when

actuator restart

132| Long| R| n.a.| CurErr| n.a| Current Error see error description above, cleared when

A clear error flag is set

134| Long| R| n.a.| [0-2^32]| n.a| Value (if exist data for error)
CyclicControlTimeOut 3)| 136| Word| R/W| min| [0-60]| 0| Raise an error CyclicTime (0x08) if no control signal is sent before timeout
MaxPositionRegime1 3)| 137| Word| R/W| µm| 0: Deactivated [1000 … 22000], (TA- Slider

750/1250) [1000 … 33000]

(TA-Slider 1600)

| 0| Max position assigned to TA-Slider when the actuator is in regime 1
MaxPositionRegime2 3)| 138| Word| R/W| µm| 0: Deactivated (only for reading) [1000 … 22000], (TA-Slider

750/1250) [1000 … 33000]

(TA-Slider 1600)

| 0| Max position assigned to TA-Slider when the actuator is in regime 2
MinPosition 3)| 139| Word| R/W| µm| [0…MaxPositionRegimei]| 0| Min position assigned to TA-Slider regardless of the regime

1. only with the relay option
2. Available from firmware version 2.0.2 (Mainboard: 4.0.0)
3. only from firmware version 1.3.0

Wiring diagrams – Terminal/Description

Terminal Description

100-240 VAC)
Up| 3-point control signal for retracting actuator spindle (24 VAC/VDC or 100-240 VAC)
B| Connection for potential free contact (e.g. open window detection), max. 100 Ω, max. 10 m

(32.8 ft) cable or shielded

COM1, COM2| Common contacts of relays 1 & 2, max. 250 VAC, max. 5A @ 250 VAC on resistive
NC1, NC2| Normally closed contacts for relays 1 & 2
NO1, NO2| Normally open contacts for relays 1 & 2

Wiring diagrams 24 V

• 24 VAC/DC operating only with safety transformer according to EN 61558-2-6

Wiring diagrams 100-240 V

• 24 VAC/DC operating only with safety transformer according to EN 61558-2-6

Wiring diagram

• Relay (TA-Slider 750/1250/1600 Plus)

• Low voltage neutral

• Ground connection required.

Wiring diagram

• BUS (TA-Slider 750/1250/1600 Plus)

Ethernet (BACnet/IP, Modbus/TCP)

RS 485 (BACnet MS/TP, Modbus RTU)

Note: A, B, A’, B’ and GND terminals are isolated from all other terminals.

We reserve the right to introduce technical alterations without prior notice. www.imi-hydronic.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>