Auverte GK100 Optical Door Window Sensor User Manual
- June 5, 2024
- AuVerte
Table of Contents
Model： GK100
GK10x Optical Door/Window Sensor
GK100 Optical Door Window Sensor
| Benefits | Models |
|---|
Optical sensing of a barrier, such as a door or a window
Wireless communication to room automation equipment
Simple to use – simple to maintain
No drilling of doors and frames for installation
True IPv6 IoT connectivity to all devices
Low cost
Ten-year warranty
Powered by CR2450 lithium coin cell battery lasting 5 years
Designed for end-of-life product recoverability| Black and white
housing colors
The GK10x optical sensor from AuVerte is part of a modern room automation solution. When used for a room entry door, this sensor is a key element to determine the occupancy status of an enclosed space in combination with one or multiple motion sensors. When used to monitor windows and balcony doors, this sensor can curtail HVAC energy during periods when the room is exposed to the outside environment. Battery-powered and utilizing wireless RF communication, the GK10x is simple to install and maintain.
C5xx Ondur Thermostat| FS10x PIR Motion Sensor| GK104 Aux.
Temperature/Humidity Sensor
---|---|---
| 
|
Specifications
Sensors
Optical Sensor| Two optical reflection sensors, sensing distance 3-10mm
depending on the reflexivity of detected surface
---|---
Sampling speed| Dynamic, less than 500 milliseconds
Radio
| Standard | IEEE 802.15.4 |
|---|---|
| Frequency band | ISM 2.4 GHz |
| Interference immunity | DSSS (Direct sequence spread spectrum) |
| Data rate | 250 kbps |
| Antenna | Build-in |
| Indoor range | Up to 50 m (150 ft) |
| Transmit power | +3 dBm |
| Receiver sensitivity | -95 dBm |
| Channels | 16 (11 to 26, default 25) |
| Protocol | AuVerte mesh |
IPv6 over 802.15.4 with forwarding error correction (FEC-ECC) via proxy
Software
| Encryption | AES128 |
|---|---|
| Routing | UDP over AuVerte Rf mesh and through an IPv6 proxy device |
| Cyber security | Packet authentication, configurable encryption keys with no |
backdoors
Device
Power| CR2450 3V/620mAh coin-cell (not included)
Approved battery vendors:
• Panasonic
• Mitsubishi
• Murata
---|---
Battery life| 5 years
Mounting| Surface mount, double-sided adhesive tape.
Environmental and Physical Specification
| Dimensions | 49mm x 27.5mm x 12mm |
|---|---|
| Weight | 0.018 kg, 0.42oz (incl. battery) |
0.012 kg, 0.63oz (without battery)
Operating temperature| 10 °C to 40 °C (50 °F to 104 °F)
Storage temperature| -20 °C to 70 °C (–4 °F to 158 °F)
Operating humidity| 10 % to 95 %RH, non-condensing
Storage humidity| 5 % to 90 %RH, non-condensing
Electromagnetic emissions| FCC Part 15 Class A
EN 62311 (EMR)
ETSI EN 300 328 (2.5GHz ISM Band)
ETSI EN 301489 (EMC)
Safety approvals| EN 60950
Environmental| RoHS
Cleaning| Mild cleaning liquid, soft towel
Recycling| 6.5g ABS, 5.5g electronics, 6.0g battery
Ordering Information
| Part numbers | 003003.GK101 |
|---|---|
| Package content | 6 GK101 sensors |
| Color Options | **** White |
**** Black
Options| None
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
© AuVerte AG
Rothusmatt 14
CH-6300 Zug
Switzerland
www.auverte.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>