ADLER EUROPE AD 2839 Blade Head User Manual

ADLER EUROPE AD 2839 Blade Head

Usage Instructions

Once the device is turned on, press the speed/power button (3). One press will turn on the device. Two presses will activate turbo mode, indicated by the speed indicator (4d).

To turn the device on or off, press the power button (4). Press and hold the power button for 3 seconds to toggle the safety lock on or off.

1. Select the desired cutting length by turning the cutting length adjustment knob (2) to 0.8 / 1.1 / 1.4 / 1.7 / 2.0mm.
2. To change the comb, turn off the clipper, unclip the current comb, and attach the desired one.
3. Start cutting by running the trimmer with the comb attachment against the direction of hair growth. Do it slowly and at a steady speed.
4. Regularly clean the trimmer and cut the head of any hair.

FAQ

• Q: What should I do for additional protection while using the product?
• A: It is recommended to install a residue current device (RCD) in the power circuit with a residual current rating not exceeding 30 mA. Please consult a professional electrician for assistance.

Introduction

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial purposes.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
3. The applicable voltage is 5V 1A. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
4. Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without supervision.
5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7. Never put the power cable, the plug or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.
8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced to avoid hazardous situations.
9. Never use the product with a damaged power cable if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
11. Never use the product close to combustibles.
12. Do not let the cord hang over the edge of a counter or touch hot surfaces.
13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, and unplug the power.
14. In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
15. If using the device in the bathroom after use remove the power plug from the socket, because water proximity presents a risk, even if the device is turned off.
16. Do not allow the device or power adaptor to wet. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put your hands in the water. Have the device checked by the qualified electrician before using it again.
17. Do not touch the device or power adaptor with wet hands.
18. The device has to be turned off after every use.
19. Do not leave switched-on equipment or adapters without supervision.
20. Never use this device close to water, e.g.: Under the shower, in the bathtub, or above the sink filled with water.
21. If the device utilises a power adaptor, do not cover it, because this can cause a dangerous temperature rise and can damage the device. Always connect the power adaptor cable to the device, and then connect the power adaptor to the power socket.
22. The cutting scissors are very sharp. Use caution when assembling, dismantling and cleaning. Do not touch any elements of the moving blade during the operation!
23. DO NOT CHARGE THE BATTERY FOR LONGER THAN 48 HOURS – this can cause irreversible damage to the battery.
24. The charging process should be conducted in temperatures between 5-35 degrees Celsius.
25. Do not wash the blades in water.
26. Only change comb attachments when the device is switched off.

PRODUCT DESCRIPTION

1. Blade Head
2. Cutting Length Switch
3. Speed button / Power Button / Safety Lock
4. DISPLAY
   • 4a. Battery Remaining Capacity
   • 4b. Charge Indicator
   • 4c. Travel lock
   • 4d. Speed indicator
5. Charging cable
6. Charging Socket
7. Combs
   • 7a. Cleaning Brush
   • 7b. Oil bottle

CHARGING THE BATTERY

• To begin charging plug the power cord into the charging Socket (6), and the charger into a 220-240V~ 50/60Hz mains power outlet. When the power adapter into the socket, the charging indicator (5d) will start blinking from bottom to top.
• After the battery is fully charged battery capacity reminder (4b) will show 100%.
• The charging time is about 2,5 hours. After that the product is fully charged, and the running time is about 180 minutes.
• When the battery reduces to 10%, the charging indicator (4b) will start to blink

SPEED CONTROL BUTTON (3) Speed Indicator (4d)
Once the device is turned on you can press the speed/power button (3).

1. press will turn on the device.
2. press will turn the device to turbo mode which will be signified with the speed indicator (4d) turning on.

POWER BUTTON / SAFETY LOCK (4)

• Press the power button (4) to turn it on or off
• Press and hold the power button (4) for 3 seconds, to turn the safety lock on or off

USING THE CLIPPER

• Select the desired cutting length by turning the cutting length adjustment knob (2):0,8 /1,1 /1,4 /1,7 /2,0mm
• To change the comb turn the clipper off, unclip the comb (fig.1) and clip on the right one (fig.2). Start cutting by running the trimmer with the comb attachment against the direction of hair growth. This should be done slowly and at a steady speed. Please remember to regularly clean the trimmer and cut the head of any hair.

CLEANING

• Clean after each use.
• Make sure the product is turned off and unplugged.
• Push the edge of the cutting head with your thumb, until it opens (fig. 3)
• Clean the cutting parts with the cleaning brush supplied (fig.4)
• Clean the inside of the product with the cleaning brush supplied. (fig.5)
• Reinstall the cutting head back to the clipper body. Make sure the bottom of the cutting head is aligned with the clipper body recess, then push the cutting head inward to the product (click) (fig.6)
• When the oiling indicator begins to blink (5a) or every five use, drop 2-3 drops of the machine oil into the space shown in fig.7 Clean the casing with a dry cloth.

TECHNICAL INFORMATION

• Power Nom: 5W
• Power: 5V 1A

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take them out and give them to the point stored separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>