HuTools HT01 Installation Instruction Manual

June 8, 2024
HuTools

HuTools HT01 Installation Instruction Manual
PLEASE KEEP THIS GUIDE

This guide contains important information about your lock.
HuTools HT01

Installation Guide

Parts List

Latch

Drive-In Collar

Strike

Exterior Assembly

Mounting Plate

Interior Assembly
Battery Cover

Latch and Strike Screws,

 Interior Assembly Screws

Mounting Plate Screws
Backup Key

1. Prepare the door and check dimensions

A. Measure to confirm that the hole in the door is 2-1/8″ (54 mm)
Prepare the door

B. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm)
Prepare the door

C. Measure to confirm that the the hole in the door edge is 1″ (25 mm)
Prepare the door

D. Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50 mm)thick
Prepare the door

2. Install the latch and strike

A. Hold the latch in front of the door hole, with the latch face flush against the door edge

Install the latch

Is the slotted hole centered in the door hole?

YES
Install the latch
No adjustment is required. Proceed to next step

NO
Install the latch
Rotate and pull the latch as shown to extend latch.
Install the latch
Install the latch

B. Is the door edge chiseled?

YES
Chiseling
Install latch in door with supplied screws.
Install the latch

NO
Chiseling

Use a flathead screwdriver to remove Rectangular face from latch and install drive-in collar.

Installing the latch Installing the
latch Installing the latchInstalling the
latch
Install latch in door with wood block and hammer.

C. Use a screwdirver to test if deadbolt works smoothy.

Installing the latch

D. Install strike on the door frame

IMPORTANT: Make sure hole in door frame is drilled a minimum of 1″ (25 mm) deep.

Installing the latch

3. Install exterior assembly

A. IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position) .
Installing exterior assembly Installing exterior
assembly

B. Route the cable below the latch

C. Send the cable through the bottom horizontal slot in the mounting plate.

D. Secure the mounting plate with the supplied screws.

4. Install interior assembly

IMPORTANT: Do not load batteries until lock is completely installed.

A. Remove the battery cover. Locate the slot at the bottom and use your fingernail or a flat head screwdriver to pry the cover up and pull it off.
Installing interior assembly

B. Connect the cable and ensure tight cable connection.
Installing interior assembly

C. Rotate the turnpiece in vertical position and the torque blade in horizontal position, make sure the latch is still fully retracted (in the unlocked position).
Installing interior assembly

D. Test operation using backup key and thumbpiece for smooth rotation.If turnpiece doesn’t rotate, repeat step 4C, making sure the turnpiece in vertical position, and touque blade in horizontal position.
Installing interior assembly

E. Secure the interior assembly with the supplied screws.
Installing interior assembly

5. Detect left/ right hand door installation

Reset the lock to teach the lock the orientation of the door.
IMPORTANT: This step is required and crucial for the lock to operate properly.

A. While the door is OPEN and UNLOCK, load 3 AA batteries into the interior assembly. For best results, use new, non-rechargeable Alkaline batteries only.
Press and hold the Reset button on the interior assembly using a pen or a paper clip.
Left/ right hand door installation

B. Press and hold the Reset button on the interior assembly using a pen or a paper clip.
Left/ right hand door installation

C. Load the last battery and keep holding the reset button for 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door.
Left/ right hand door installation

How To Use

UNLOCK the door from outside
Using
UNLOCK the door from inside
Using
Rotate the thumb turn to Unlock position.

UNLOCK the door from outside LOCK the door from outside
Manual Mode
Press any key on keypad for 2 seconds.

Auto Re-lock Mode
In Auto re-lock mode, the bolt will extend out automatically in 30 seconds after unlocking.

LOCK the door from inside
Manual Mode
Rotate the thumb turn to Lock position
Using
Auto Re-lock Mode
In Auto re-lock mode, the device will be locked automatically.

Programming Instructions

Information & Safety Warnings
  • Protect your User Codes and Master Code.
  • Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
  • This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.

IMPORTANT: Do not load batteries until lock is completely installed.

  1. Master Code( 4 to 10 digits) : The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
  2. User Code(4 to 10 digits) : A total of 20 User Codes (and one temporary one-time User Code) may be programmed.
  3. Both master and user pin codes don not support the following combination of numbers.

A.Programming   Forward number sequence
B.
Backward number sequence
C.Programming Backward number sequence
D. If Programming

Then Programming Contain existing code sequence
and Programming

Parts Illustrations

Item: Specifications: Remarks

Battery (Use new, non-rechargeable Alkaline batteries only.): AA alkaline battery x4 (Operation voltage: 4.6~6.0V): Last up to one year (10 times open/close per day)

Exterior Assembly

Exterior Assembly

Interior Assembly

Interior Assembly

The default Master Code is 12345678. It is required that you change it to a code of your own before programming.

Definitions

Master Code
Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming.
Property owner/ manager should keep this information confidential.
Auto Lock
Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can set the Auto Lock time delay between 10 and 99 seconds.
Wrong Entry Limit
After 10 unsuccessful attempts at entering a valid PIN code, the unit will shut down for 3 minuets.
Silent Mode
The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.
Vacation Mode
This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock is unlocked by thumb turn, the lock will sound an alarm.
One Time User Code
This code can only be used once and is automatically deleted when used.
Unlock with Fake code
User can prevent pin code exposure from strangers by entering random digits before or after pin code.

Quick Set Up

IMPORTANT: The default Master Code is 12345678. It is recommended that you change it to a code of your own.

Set Up
Set Up
Set Up
Set Up
Set Up
Set Up

Factory Default Settings

Settings: Factory Defaut

MasterCode: 12345678
Auto Lock: Disabled
Silent Mode: Disable
Wrong Code Entry Limit: 10 times
Shutdown Time: 3 mins
Vacation Mode: Disabled

Restore To Factory Default Settings

This procedure will delete all User Codes associated with the lock.

  1. Keep the door open and unlock.
  2. Press and hold the Reset button, at the same time take out one battery and then place it back.
  3. Keep holding the Reset button for 3 seconds, until you hear the sound of beep.

Troubleshooting

The turnpiece cannot rotate or operate the lock.
Remove and re-install the lock, making sure that the turnpiece is in vertical position.
The lock cannot be locked or unlocked by the keypad.
Make sure that the codes are not disabled. If needed, restore the lock’s default settings.
The keypad doesn’t respond when touched ( no lights are visible and no beeping is heard) .
Make sure the cables are properly connected, and make sure the batteries are new and installed correctly.
After the installation of the batteries, there is no response when you press any button and no beeps are heard.
Check the cable connection and the polarity of the batteries. Also make sure the batteries are not dead.
I forgot my Master Codes.
Perform a reset in order to erase all passcodes. Once the reset is complete, all passcodes will be erased and the Master code will return to the default value (12345678).

***** If none of the above resolves your issue, check out our updated user manual by scanning the code below. You could also contact Hutools customer service at support@hutools.com.

HuTools HT01 Installation Instruction Manual – Optimized PDF
HuTools HT01 Installation Instruction Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals