HuTools DKS02 Fingerprint Keyless Entry Door Lock Deadbolt User Guide

: June 14, 2024
: HuTools

DKS02 Fingerprint Keyless Entry Door Lock Deadbolt

DKS02 Fingerprint Door Lock

Specifications:

Model: DKS02
Lock Type: Fingerprint Door Lock

Installation Overview:

Detect door orientation
Install the physical lock
Change the default master code
Customize settings

Important Tips for Successful Installation:

Always reset your lock after installation.
Do not use an electric drill to tighten screws.
Wait to install the batteries until instructed to do so.
Change the default master code before programming.

Parts List:

Latch A
Strike B
Interior Assembly E
Battery Cover F
Mounting Plate Screws I x 2
Keypad Assembly C
HuTools
Mounting Plate D
Interior Assembly Latch Strike Screws G x 2
Screws H x 2
Screws J x 1
Reset Tool K x 1

Installation Instructions:

1. Door Measurements:

Backset: The distance from the door edge to the center of the
hole on the door face.

For a 2 3/8″ (60mm) backset, rotate the latch to extend it.

For a 2 3/4″ (70mm) backset, no adjustment is needed.

2. Adjust Latch Backset:

Install the latch. For a 2 3/8″ (60mm) backset, rotate the latch
to extend it. For a 2 3/4″ (70mm) backset, no adjustment is
needed.

3. Install Strike on the Door Frame:

Do not overtighten screws. Make sure the hole in the door frame
is at least 1″ (25mm) deep.

4. Check Alignment:

With the door closed, check the alignment between the latch and
the strike plate. Make sure that when the deadbolt is extended, it
goes into the bolt hole and does not hit the deadbolt strike or
door frame.

5. Install Keypad Assembly:

Install the keypad assembly and mounting plate. Keep it parallel
to the door edge. Do not overtighten screws.

6. Install Interior Assembly:

Do not put batteries in yet. Connect the cable by pushing the
connector in firmly until it is completely seated. Check deadbolt
operation by turning the thumbturn back and forth. If the thumbturn
doesn’t rotate, repeat steps and apply more force.

7. Detect Door Orientation / Factory Reset:

Always reset your lock after installation. The motor will not
operate before completing this step.

8. Install Batteries:

Install batteries. Use new, non-rechargeable Alkaline batteries
only and do not mix old and new batteries.

9. Reset the Lock:

Press and hold the reset button with a pen or a paper clip and
proceed to the next step. Place the third battery and keep holding
the reset button until the latch extends. If the latch doesn’t
extend within seconds, repeat steps and make sure the latch is
always retracted.

10. Test the Lock:

Test with the door open to avoid accidental lockout.

Locking: Press and hold any key for seconds.

Unlocking: Press any key to activate.

Program & Use:

UNLOCK from outside:

Press any key to activate.
Enter Master code / User code OR touch and hold the sensor with
your finger.
Press # to confirm.

LOCK from outside:

Enable Auto Lock (see page 11) OR press and hold the Lock button
on the keypad for 2 seconds.

FAQ:

Q: How do I change the default master code?

A: Before programming, you must change the default master code

(which is 7) to a code of your own.

DKS02 Fingerprint Door Lock

In

nn O

n n

Installation Overview

Detect door orientation ( age )

1

Install the physical lock ( age 2 )

2

Change the default master code ( age 1 )

Customize setting ( age 1 11)

Important tips to ensure a successful installation:

l ays reset your lock after installation.
Do not use electric drill to tighten scre s.
ait to install the batteries until instructed to do so.

Change the default master code before programming.

Questions? lease reach out to us for help.
1

Parts List

Latch A

Strike B

Interior ssembly
E

attery Co er F

Mounting late Scre s I x 2

eypad ssembly

C

HuTools

Mounting late
D

Interior ssembly Latch Strike

Scre s

G x 2

H x

J x 1

Reset Tool
K x 1

C
HuTools
A

E D
I

F G J

Micro USB Power Port

H H B
TOOL RE IRED
2

NO ELECTRIC DRILLS

Installation Instructions

1 Door Measurements
21 8 54 mm

2 8 or 2 or mm

backset

1 25mm

1 8 to 2 5 mm to 5 mm

Adjust Latch Backset

Backset: The distance from door edge to center of hole on door face.

or 2

(70mm) backset rotate the latch to extend latch.

or 2 8 ( 0mm) backset no ad ustment is needed.

backset
3

Installation Instructions (Continued)
Install the Latch

H

Install Strike on the door frame

Do not o ertighten scre s.

Make sure hole in

door frame is at B least 1”(25mm)

H

deep.

Check Alignment
ith the door closed check alignment bet een the latch and the strike plate making sure hen the deadbolt is extended it is going into the bolt hole and not hitting the deadbolt strike or door frame.
4

Installation Instructions (Continued)
Install Keypad Assembly
unlocked
Install Mounting Plate
Keep parallel to door edge.
I
unlocked
Do not o ertighten scre s.
5

Installation Instructions (Continued)

Install Interior Assembly

8a

8b

Don’t put batteries in yet.

Connect the cable by pushing connector in firmly until it is completely seated .

8c unlocked

8d ertical

GG J

8e Check deadbolt operation by turning the thumbturn back and forth. If thumbturn doesn’t rotate, repeat steps 8c and apply much more force.
6

Detect door orientation / Factory reset
l ays reset your lock after installation. The motor ill not operate before completing the step.

9a

Install batteries.

Use ne , non rechargeable Alkaline batteries only and do not mix old and ne batteries.

unlcoked

9b
ress and hold the Reset button ith a pen or a paper clip and proceed to the next step.

ertical
reset button

9c

lace the th battery and keep holding the reset button until the latch extend.

If the latch doesn t extend ithin seconds, repeat step C and A, making sure the latch is al ays retracted.

Test the Lock (test ith the door open to avoid accidental lockout)

Locking: Press and hold any key for seconds.

Unlocking: Press any key to activate

7

Program & Use

UNLOCK from outside

1 Press any key to activate.

Touch and hold the

2 Enter Master code / User code.OR sensor with your

3 Press

to confirm.

finger.

LOCK from outside Enable Auto Lock ( see page11) OR Pserecossnadnsy button on keypad for 2
Programming Basics
EA this before programming.

A Master Code

· Master code is the administrative code for program lock

functions. It ill also unlock the door. he default master code

is

· or security reason, the default master code dose not program

the lock. ou must change it to a code of your o n prior to

programming.

B Code Format · Code is 0 digits long. · Codes ith the follo ing se uence are not supported.

a. or ard number se uence, ex.

7

b. ack ard number se uence, ex. 7

c. epeat number se uence, ex.

d. Contain existing code se uence,

ex. If is an existing code, then 7

is not supported.

8

Program & Use (Continued)
C Wrong Entry Limit · After 0 unsuccessful attempts at entering a valid access code, the lock ill shut do n for minutes.
D Unlock with Fake code User can prevent pin code exposure from strangers by entering random digits before or after pin code.
3 1 13 1 2 14 10 pass ord random digits
E Battery Indicator If you see 0 red ashes after pressing any key or lock and unlock the door, that’s an indication that the batteries need to be replaced soon. Please replace ith ne AA alkaline batteries and do not mix old and ne batteries. All settings are retained in the memory hen the batteries are removed and replaced.
F Micro USB Power Port Micro USB charging port is under the exterior keypad. When locked out or dead batteries, use a Micro USB cable to connect a portable power bank, it can supply power for keypad or reboot keypad.
9

Program & Use (Continued)

Important Tips:

· uring a programming steps, the

button turns green

to indicate that you can proceed. Please proceed to the next

steps before the green light goes off.

e· Inftyroyuerhreoar.rPleraapseidsbtaeretposveri.th ashing red lights, it indicates

· Activate the keypad by press

before programming.

AA.Change Master Code

he default Master Code is

7 . It is re uired that you change

it to a code of your o n prior to programming the lock.

Master Code Enter the e Code Again

1 e Master Code

B Add User Code · Up to 0 User Codes can be created.
Master Code Enter the New Code Again

2 e User Code

C Delete User Code
Master Code

3

Un anted User Code

DDAdd Fingerprint · Up to 20 fingerprints could be added.

Master Code

4 Scan Fingerprint 5 Times

EDDelete Fingerprint
Master Code

5 Scan Unwanted Fingerprint

10

Program & Use (Continued)

DF.Disable Silent Mode
Master Code

61

G Enable Silent Mode

· he beep sounds hen pressing keypad can be muted.

Master Code

62

H Enable Auto Lock
· Automatically locks the deadbolt his feature is off by default.
Master Code

0 seconds after unlocking.
71

I Disable Auto Lock
Master Code

72

J Set Auto Lock Time Delay
· ou can set the Auto ock time delay bet een 0 and
Master Code

seconds.

I Vacation Mode · his is a security feature for you hen you are leaving your home for vacation or long trip. It restrict all user codes until master code is entered on keypad.
Master Code

K Add One-Time Code

· his code can only be used once and is automatically deleted hen used.

Master Code

e ne ime Code

Enter the e Code Again

11

Program & Use (Continued)

Factory Default Settings
ettings
Master Code Auto ock ilent Mode
rong Code Entry imit acation Mode

actory efaut
7 isabled isabled 0 times isabled

How To Reset
y performing the steps belo , you ill teach the lock the orientation of your door and delete all User Codes associated ith the lock.
Step1 Keep the door opened, latch retracted and thumbturn vertical.
Step2 Press and hold the reset button ith one hand and the other hand takes out one battery and places it back Keep holding the reset button until the latch extends.

Safety Warnings

· Protect your Master Code.

· estrict access to your lock s interior assembly and routinely check your settings

to ensure they have not been altered ithout your kno ledge.

· Proper cleaning and maintenance of your lock ensures it ill continue to ork

as it should.

· o not apply cleaner or detergent directly to any part of the lock.

· he u ools lock meets IP ater resistance. It can ithstand ater splashes

ho ever, do not let ater and li uids get into the lock.

· Avoid exposure to direct sunlight. ong term exposure to direct sunlight may

damage the lock.

· he temperature range of the u ools lock is bet een to

.

1

Troubleshooting

When

Solution Refers to

Thumbturn won’t rotate by hand.
Installing
Doesn’t work on the left-hand door or right-hand door.
The latch goes in and out.
The latch retracts.

A B
A H J C D E
F G Q L

Reset

The latch doesn’t extend but there’s motor turning sound.
The latch doesn’t extend and not making any sound.
I lost all the preset codes after door handing.
Lock won’t programmed.

C D E F G H Q A C D
K
C M

Unable to change master code.

C M

Program

Unable to add user code. Unable to add fingerprints.

Lock won’t store previous settings, have to reprogram many times.

I forgot my master code.
Need to delete someone’s fingerprint, but the person is not here.
Need to delete an user code, but don’t remember the code.

C M C M N
C H H H

13

Troubleshooting

When
Thumbturn won’t rotate by hand.

Solution Refers to
A B

Keypad doesn’t respond when touched (no lights are visible and no beeping is heard) .
The keypad light never goes off.

CD R C D

Using

Deadbolt doesn’t lock/extend when pressing any key for 2 seconds.
Deadbolt doesn’t unlock/retract when entering codes +
Deadbolt doesn’t unlock/retract when holding fingerprint sensor.
Deadbolt extends when entering codes +
Deadbolt extends when holding fingerprint sensor.
Deadbolt unlocks/retracts when pressing any key for 2 seconds.

Deadbolt won’t FULLY extend or retract

When LOCK or UNLOCK, the latch goes in and out for a few times.

Batteries died and I’m locked out.

A H J
I AHJ N O A H J L
L
L CDE F G J PQ CDE F G P Q
R

How do I know when batteries are low?

S

14

Troubleshooting
Solutions
A Make sure the thumbturn is vertical and door unlock when installing. B Use much more strength to rotate the thumbturn. C Step 1: Make sure the cable is properly seated when connecting.
Step 2: Make sure the batteries are placed properly. Step 3: Change another 4 fresh AA alkaline batteries. D Disconnect all batteries. Press and release any key and keep the batteries disconnected for at least 5 minutes. E Make sure the end of latch bolt doesn’t touch the wood in the door hole. Enlarge the door hole if needed. F Slightly loosen the screws H & I. G Make sure the latch and the strike plate are properly aligned and make sure to reset the lock with the door opened. H Repeat (Step 8) for factory reset. All codes, fingerprints and settings will be erased after reset. The default master code is 12345678. I Hit (not hold) any key to activate the keypad before entering code. J Check that if latch bolt is broken. K Door handing is the same as factory reset. Your lock has restored to factory default. Re-program your codes. L Re-install and reset the whole lock, make sure the latch is retracted and thumbturn vertical when installing. M Step 1: Press the next button within 6 seconds. Step 2: Check if the current master code you entered is correct. Step 3: Change master code first. Step 4: Enter a new code in correct format and within 4 to 10 digits long. N Step 1: Clean your finger to ensure it is not wet, moisty, or dirty. Step 2: If the scanner has any liquid or dirt, clean it with a dry cloth. Step 3: Make sure this finger has been registered. O Touch and hold the fingerprint sensor for about 1 to 2 seconds.

Troubleshooting
Solutions
P Step 1: Make sure the bolt hole on the door frame is at least 1 inch deep so the bolt fully extends. Step 2: Check if the door closes properly. Make sure when the deadbolt is extended, it is going into the bolt hole and not hitting the deadbolt strike or door frame. Step 3: Check for loose door hinges. Q Remove the lock from the door. Re-assemble lock without securing screws and mounting plate on hand. Then reset the lock on hand, and test locking and unlocking. This can test if lock is defective. R There’s a micro-usb charging port under the exterior keypad. Use a Micro USB cable to connect a portable phone charger to supply power for keypad. Note that this is not to charge the batteries. S When batteries are running low, you’ll see 10 flash red lights after pressing any key on keypad. ** If none of the above resolves your issue, please contact us at support@huTools.com.