HuTools HT02 Fingerprint Electronic Lock with Keypad Instruction Manual
- June 6, 2024
- HuTools
Table of Contents
- PROGRAM MANUAL
- A. Notes Before Installation
- B. Reset the Factory Setting
- C. Change the Master Code
- D. Add User Codes
- E. Delete the User Code
- F. Add User Fingerprint
- G. Delete User Fingerprint
- H. Mute the Button
- I. Activate the Keypad Sound
- J. Enable Auto Lock Feature
- K. Change Auto Lock Time Delay
- L. Close the Auto Lock Feature
- M. Enable the Vacation Mode
- N. Add One Time Pin Code
- O. Anti-Peep Password Feature
- P. How to lock the door
- Q. How to unlock the door
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HuTools Lock YouTube Channel:
https://www.youtube.com/channel/UCioengOED93npCiMCmwJR0A
PROGRAM MANUAL
HT02 & KS02
A. Notes Before Installation
Please kindly check the package list: Interior Assembly (F) and Battery Cover (G) has already combined together. Please remove the battery cover before installation.
See the video of how to install: https://youtu.be/hNJmoSzf4aE
-
The Thumb Turn-piece must be vertical and the deadbolt latch needs to be in the unlocked position when installing.
-
Verify that the deadbolt latch is in the proper position and check that the screws securing the latch bolt are not over-tightened.
-
Reset the lock is required after installation. (Reset the lock to learn the orientation of the door.)
-
Make sure the bolt hole on the door frame is at least 1 inch deep so the bolt fully extends.
-
Check that the door closes properly so that when the deadbolt is extended, it is going into the bolt hole and not hitting the deadbolt strike or door frame.
-
Please use 4 fresh AA standard alkaline batteries, Rechargeable or Extended Life
batteries shouldn’t be used with the lock. -
Make sure the cable is properly connected, and make sure the batteries are installed correctly.
B. Reset the Factory Setting
(Teach the lock to learn the orientation of the door)
See the video of how to reset: https://youtu.be/iMhJDAb4fCQ
Note: make sure the door is OPEN. The Thumb Turn-piece must be vertical and the deadbolt latch needs to be in the unlocked position.
(1) Insert 3 batteries in the lock, NOT insert the 4th battery;
(2) Use a pin to push the reset button and keep holding it;
(3) Don’t release the pin and insert the 4th battery; keep holding the
pin for about 10 seconds. After you hear the sound of “beep” and the latch
bolt extends out, you can release the pin.
(4) Test 3 situations:
Firstly, keep the latch bolt in extending out status, then use default master
code (12345678) to test if it can be unlocked.
Secondly, use the mechanical key to test the unlock and lock.
Thirdly, keep the latch bolt in unlocked status, press any one button on
keypad, to see whether the latch bolt can come out or not.
(5) If the latch deadbolt can go back and forth smoothly, then please go
to next step: to change the master code to your own.
C. Change the Master Code
(Make sure you have reset the lock)
See the video: https://youtu.be/lgAR43W8rYo
(1) Push the HuTools button twice;
(2) Enter the default master code 12345678 ;
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button ” 1 “, the HuTools button will has green
light flash and a long sound beep.
(5) Enter the master code you want (4-10 digits), then push HuTools
button once, the HuTools button will has green light flash and a long sound
beep.
(6) Repeat the step 5. [Enter again the same master code (4-10 digits),
then push HuTools button once, the HuTools button will has green light flash
and a long sound beep.]
The setting is finished. Now you have your own master code. Each lock can only has one master code.
D. Add User Codes
Make sure you have changed the master code.
See the video: https://youtu.be/ezvrIa1DzOM
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button ” 2 “, the HuTools button will has green
light flash and a long sound beep.
(5) Enter the user code you want (4-10 digits), then push HuTools button
once. The HuTools button will has green light flash and a long sound beep.
(6) Repeat the step 5. [Enter again the user code you want (4-10 digits),
then push HuTools button once, the HuTools button will has green light flash
and a long sound beep.]
This time you have your user code. You can use the code to open the door.
E. Delete the User Code
See the video: https://youtu.be/8RoJrNusj_s
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button ” 3 “, the HuTools button will has green
light flash and a long sound beep.
(5) Enter the UNWANTED user code, then push HuTools button once. The
HuTools button will has green light flash and a long sound beep.
The unwanted user code is deleted.
F. Add User Fingerprint
See the video: https://youtu.be/bFbZLKuVSHI
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button ” 4 “, the HuTools button will has green
light flash and a long sound beep.
(5) Scan your fingerprint 8 times, each time scan successfully you will
hear a short sound beep. When you finish scanning 8 times, the HuTools button
will has green light flash and a long sound beep.
This time you have your user fingerprint. You can use the fingerprint to open the door.
G. Delete User Fingerprint
See the video: https://youtu.be/gCKIK5MMA1I
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button ” 5 “, the HuTools button will has green
light flash and a long sound beep.
(5) Enter the UNWANTED user fingerprint once. The HuTools button will has
green light flash and a long sound beep.
The unwanted user fingerprint is deleted.
H. Mute the Button
See the video: https://youtu.be/BgCwdw_FnoE
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “6”, the HuTools button will has green light
flash and a long sound beep.
(5) Press the number button “2”, and then push the HuTools button once.
The HuTools button will has green light flash and a long sound beep.
Finish the setting, the button will be mute. Enable the silent mode only mutes the sound when pressing keypad. You will still hear low battery and system alerts.
I. Activate the Keypad Sound
See the video: https://youtu.be/Y3y8rH2HC0I
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “6”, the HuTools button will has green light
flash and a long sound beep.
(5) Press the number button “1”, and then push the HuTools button once.
The HuTools button will has green light flash and a long sound beep.
The silent mode is off. You will hear the sound when you press the keypad.
J. Enable Auto Lock Feature
See the video: https://youtu.be/zboE5pQmUis
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “7”, the HuTools button will has green light
flash and a long sound beep.
(5) Press the number button “1”, then push the HuTools button once. The
HuTools
button will has green light flash and a long sound beep.
(6) The deadbolt latch will auto lock and extend out and in 30 seconds,
with 2 short beep sounds and red light flash on HuTools button.
The auto lock feature is enabled. It will auto lock in 30 seconds.
K. Change Auto Lock Time Delay
If you think that the 30 seconds auto lock time is too long or too short, you can change the auto lock time (10 to 99 seconds) by the following steps.
See the video: https://youtu.be/1rOE0ugKwv4
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “0”, the HuTools button will has green light
flash and a long sound beep.
(5) Enter the time you want to set ( allow 10 – 99 seconds ), then push
the HuTools
button once. The HuTools button will has green light flash and a long sound
beep. (For example, if you want to set 12 seconds, then you enter the number
“12”, then push HuTools button.)
(6) The deadbolt latch will auto lock and extend out in the time you set,
with 2 short beep sounds and red light flash on HuTools button.
The auto lock time setting is finished.
L. Close the Auto Lock Feature
See the video: https://youtu.be/Rws7xJwj4ns
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “7”, the HuTools button will has green light
flash and a long sound beep.
(5) Press the number button “2”, and then push the HuTools button once.
The HuTools button will has green light flash and a long sound beep.
The auto lock feature is off. You have to press any one button for 3 seconds to lock it. Or use the mechanic key to lock the door.
M. Enable the Vacation Mode
See the video: https://youtu.be/VNOIGP3bBIA
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “8”. The HuTools button will has green light
flash and a long sound beep.
(5) Push the HuTools button once. The HuTools button will has green light
flash and a long sound beep.
The vacation mode is enable. This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock is unlocked by thumb turn inside the door, the lock will sound an alarm.
N. Add One Time Pin Code
See the video: https://youtu.be/UF1-Hvmh5gA
(1) Push the HuTools button twice;
(2) Enter your own master code (which you have set before);
(3) Push the HuTools button once, then the HuTools button will has green
light (not flash) and there’s a long sound beep.
(4) Press the number button “9 “, the HuTools button will has green light
flash and a longsound beep.
(5) Enter the one time user code you want (4-10 digits), then push
HuTools button once. The HuTools button will has green light flash and a long
sound beep.
(6) Repeat the step 5. [Enter again the one time user code you want (4-10
digits), then push HuTools button once. the HuTools button will has green
light flash and a long sound beep.]
One time user code is set successfully. You can use the code to open the door. It will be invalid after one time use.
O. Anti-Peep Password Feature
The anti-peep password is to add numbers before or after the user codes, or add numbers on the before and after simultaneously. The total numbers you input (plus the correct user code) can not exceed 20 digits.
If the correct user code is 930871 , to use this anti-peep feature, I can input 42583 930871 , or 930871 572893, or 4827 930871 831675. If input 458632 930871 468275163 (21 digits), the lock will not work. The length of the correct user code should be 4-10 digits.
This way is to lengthen the numbers you input, which makes someone who wants to pry hard to remember the long numbers. Every time inputting different numbers plus correct code can also avoid leaving heavy fingerprints.
P. How to lock the door
How to lock the door from outside
Method 1: Press any one button on keypad for 3 seconds.
Method 2: Set the auto lock feature.
How to lock the door from inside
Method 1: Rotate the turn knob to lock position (horizontal).
Method 2: Set the auto lock feature.
Q. How to unlock the door
How to unlock the door from outside
Method 1: Fingerprint access
Method 2: Input master code + HuTools
Method 3: Input user code + HuTools
How to unlock the door from inside
Rotate the turn knob to unlock position (vertical).
References
- HuTools Lock - YouTube
- Change Auto Lock Time Delay - HuTools Fingerprint Keypad Deadbolt Lock [ HT02 / KS02 ] - YouTube
- Delete User Code - HuTools Fingerprint Deadbolt HT02 / KS02 - YouTube
- Add User Fingerprint - HuTools Fingerprint Deadbolt Lock HT02 / KS02 - YouTube
- Enable Silent Mode - HuTools Fingerprint keypad Lock HT02 / KS02 - YouTube
- Add User Code - HuTools Fingerprint Electronic Door Locks [ HT02 /KS02 ] - YouTube
- Delete User Fingerprint - HuTools Electronic Door Locks HT02 / KS02 - YouTube
- How to Install - HuTools Fingerprint Keyless Entry Door Lock [ HT02 / KS02 ] - YouTube
- Reset to Factory Settings / Teach the Lock the Orientation of the Door for HuTools lock - YouTube
- Change Master Code - HuTools Fingerprint Digital Door Lock [ HT02 / KS02 ] - YouTube
- Disable Auto Lock - HuTools Fingerprint Lock HT02 / KS02 - YouTube
- Add One time User Code - HuTools Fingerprint Door Lock HT02 / KS02 - YouTube
- Enable Vacation Mode - HuTools Fingerprint Keyless Entry Door Lock [ HT02 / KS02 ] - YouTube
- Disable Silent Mode - HuTools Fingerprint Deadbolt Lock [ HT02 / KS02 ] - YouTube
- Enable Auto Lock - HuTools Fingerprint Biometric Deadbolt Lock [ HT02 / KS02 ] - YouTube
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>