GOLDEN LIGHTING 1020-6 BLK-MWS 6-Light Matte Black Modern White Shade Chandelier Instruction Manual

GOLDEN LIGHTING 1020-6 BLK-MWS 6-Light Matte Black Modern White Shade

Chandelier

IMPORTANT

• All installation work should be done by an accredited professionals.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.

1. From the parts bag remove the mounting strap assembly. One end of the threaded nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place.

2. Place mounting strap (A) over the junction box and secure in place with mounting screws (B) and a screwdriver. Tighten the screws securely.
   ASSEMBLING THE FIXTURE

3. Measure to determine the correct length of chain needed for proper hanging height. To shorten the fixture, trim the wires to the desired length plus at least 8 to 10 inches. If necessary, use a pair of pliers to open and remove any excess chain.

4. Attach top rings (Q) to top loop (L). Attach chain connectors (K) to each end of chain(J) before attaching one end of the chain connector/chain to top loop (L). Connect the other chain/chain connector to canopy loop (H). Close the chain connectors (K) to secure. One of the fixture’s rods (N) is on the fixture wires. Pull the wires until taut and feed through top ring (Q), top loop (L), chain (J) (every three links or so), canopy loop collar (I), canopy loop (H), and canopy (G). Pull the wires until taut. Hang one hook end of the rods (N) onto top rings (Q) and attach the other hook end of the rods (N) onto the rings (M) found on the fixture body.

5. Slide canopy loop collar (I) and canopy (G) down onto the chain/wires.
   CONNECTING THE WIRES

6. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
   FINISHING THE INSTALLATION

7. Push canopy (G) up to the ceiling so that threaded nipple (F) protrudes through the hole in the canopy (G). Secure canopy (G) to the ceiling by threading canopy loop collar (I) onto canopy loop (H). Twist until the canopy (G) is snug against the ceiling. 8. Slide candle sleeves (O) over sockets (R) which rest on cups (P). Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. 9. Shades (S) purchased can be slid over the installed light bulbs. Your installation is now complete. Turn on the power and test

How to Identify the Fixture’s Wires

• Hot: Smooth, Black, or Transparent with Black Inner Thread
• Neutral: Ribbed, White or Transparent with White Inner Thread
• Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

OVERVIEW

DIMENSION

• Pendants & Linear Pendants Above a Kitchen Island Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
• Pendants & Chandeliers Above a Dining Room Table Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
• Pendants and Chandeliers in Open Areas The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.

Love your light and want to show it off? Follow us, share a picture, and tag us on Social

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>