AGPTEK Wireless Car Charger User Manual
- June 7, 2024
- AGPTEK
Table of Contents
AGPTEK Wireless Car Charger User Manual
Product Introduction
- Provides fast wireless charging up to 10W for Android, 7.5W for iPhone, and 5W for standard wireless charging speed.
- Meet Qi specification. Support all phones which meet Qi specification to charge wirelessly.
- Please use the car charger that meets the QC2.0 or higher standard. If the car charger does not meet the specifications, it may not provide enough power, which will affect the speed of wireless charging.
- Adjust the height of the charger’s bottom bracket. Make the wireless charging receiving coil of your mobile phone aligning with the transmitting coil of wireless charger, which will get the higher efficiency of wireless charging.
- After the car is off, you can grasp the clamps with both hands, and then pull the clips of both sides simultaneously to remove the phone.
Package Contents
- Wireless Car Charger x 1
- Type-C Cable x 1
- Suction cup mount*1
- 4. Air vent mount x 1
- User manual x 1
- Box x 1
Buttons and Control
Note: When charging, the LED indicator turns blue; If does not, it turns red.
Operation
-
Select the Air vent mount or Telescoping suction cup mount according to your need.
-
Unscrew the nut and insert it to the ball joint. Insert the ball joint forcibly into the socket at the back of the wireless charger and tighten the nut.
-
Install the mount into the car air vent louver or other places. Connect wireless charger to the corresponding port with Type C cable or Micro USB cable(Not included). The other end of cable is connected to car charger with QC 2.0 or above specification. At this time, LED indicator of wireless charger turns red.
-
Place the phone that can be charged by wireless charger about 10 cm away from the wireless charger. The clamp arms will automatically stretch and you put in phone. The clamp arms will fix your phone automatically. If the wireless charger is unable to charge or charge slowly, please adjust the height of bottom bracket until the phone can be charged normally – that the LED indicator turns blue.
Take out mobile phone
- Before the car is off, press one of touch switch in both sides. Take out the phone after the clamp arms are fully stretched.
- After the car is off, grasp the clamp arms with both sides with both hands. At the same time, pull the clamps on both sides to remove the phone.
Warnings
-
Work well with all other Qi enabled devices.
-
For fast charging, you must use a car charger that meets QC 2.0 and higher standard.
-
Mobile phone case with magnetic, metal and ring bracket is not supported.
-
The phone case is so thick that it will reduce the wireless charging efficiency or can not charge. 5. Keep the product away from water or other liquids.
Specification
| Input | 5V/2A; 9V/1.67A |
|---|---|
| Output power | 10W/7.5W/5W |
| Charging efficiency | ≤87% |
| Charging distance | ≤8mm |
| Infrared induction distance | About 10cm(Different color of phone cases may be |
Different induction distance.)
Troubleshooting & Tips
Trouble
| Causes|
Tips
---|---|---
LED indicator is on, but unable or slow to charge.| The wireless charging coil
is not align.| Adjust the height of wireless car charger’s bottom bracket,
making the phone in place.
The car charger does not meet QC 2.0 or higher standard.|
Replace the car charger.
Charging cable is too poor or broken.|
Replace the cable.
Mobile phone case with magnetic, metal, ring bracket.|
Take out phone case or replace the phone case.
Mobile phone case is too thick.| Remove phone case or use the thinner phone
case.
The indicator is off and the charger does not charge.| The car is off.| Turn
on the car.
Charging cable is loose.| Check out the cable and plug it firmly.
Charging cable is damage.| Replace the cable.
The car charger is broken.| Use the charger with QC 2.0 or higher standard.
Suction cups mount is not sucking firmly.
| Forget to press the switch of
suction cup.
|
Press the switch.
Too much dust on the suction cup mount.| Clean the suction cup with water.
The mount is loose.| Cannot screw the nut tightly.| Screw the nut tightly.
Contact Details:
@agptek.fans
@AGPTEK_fans
agptek.fans
Visit agptek.com to know more about us.
Contact us: support@agptek.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>