ZALMAN ATX MID Tower Computer Case User Manual
- June 7, 2024
- ZALMAN
Table of Contents
ATX MID Tower Computer Case
User’s Manual
Ver. 102320
- To ensure safe and easy installation, please read the following precautions.
- Product design and specifications may be revised to improve quality and performance without notice.
Developed and designed by ZALMAN in Korea. This product is protected by ZALMAN’s pending or registered patents.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | T8 |
|---|---|
| Case Form Factor | ATX Mid-Tower |
| Dimensions |
394.5 x 200 x 423(H)mm
Weight| 2.6kg
Case Materials| Plastic, Steel
Motherboard Support|
ATX / mATX / Mini-ITX
Maximum VGA Length| 295mm
Maximum CPU Cooler Height| 160mm
Maximum PSU Length| 140mm
PCI Expansion Slots| 7
Drive Bays|
1 x 5.25″, 2 x 3.5″, 4 x 2.5″
Front Fan Support
| Front|
2 x 120mm / 2 x 140mm
Rear| 1 x 120mm
Side| 1 x 120mm
Fan(s) Included| Rear| 1 x 120mm
Radiator Support
| Front|
1 x 120mm 1 x 120mm
Rear| 120mm
I/O Ports|
Power Button, RGB LED Button, 1 x Mic, 1 x Headphone, 2 x USB2.0, 1 x USB3.0
Accessories component
I/O Ports
Part
a. Power Button
b. HDD / Power LED
c. RGB LED Button
d. USB 2.0 Port
e.Headphone Jack
f. Microphone Jack
g. USB 2.0 Port
h. USB 3.0 Port
1. Removing the side panels
2. Removing the front panel
3. Foot Pads Installation
4. Mounting the motherboard
4-1. Motherboard size
5. Mounting PCI-E(VGA) card
6. Mounting the ODD
7. Mounting the 2.5″ SSD
8. Mounting the 2.5″ SSD
9. Mounting the 3.5″ and 2.5″ SSD / HDD
10. Mounting the PSU
11. Mounting the radiator
12. Mounting the fans
13. Fan(s) Included / Fan Specifications
Rear
– Dimensions : 120 x 120 x 25(H)mm
– RPM : 1,100 -15% – Fan : DC 12V 0.15A+20%
– Sleeve Bearing
– Power Connector : FAN-3PIN
14. I/O Connectors
Certification
This mark, designed by Zalman, Indicatos product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.
Dlapoull of Old Electrical & Electronk Equipment (Applicable in the European Unlon and other European countries with separate collection systems)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>