ORNO OR-GM-9003 Furniture Socket Instructions
- June 3, 2024
- ORNO
Table of Contents
OR-GM-9003 Furniture Socket
Instructions
DIRECTIONS FOR SAFTY USE!
Before using the device, read this manual and keep it for future reference. Making repairs and modifications by yourself will result in the loss of warranty. The manufacturer is not liable for damage that may result from incorrect installation and operation of the device. Due to the fact that the technical data are subject to continuous modifications, the Manufacturer reserves the right to amend the characteristics of the product and introduce other design solutions that do not impair the parameters and usefulness of the product. The current version of manual can be downloaded from the website www.support.orno.pl. All rights to translation/interpretation and copyrights in this manual are reserved.
- Do not use the device against its intended use.
- Disconnect the power supply before any activities on the product.
- Do not immerse the device in water or other fluids.
- Do not operate the device when its housing is damaged.
- Do not open the device and do not repair it by yourselves.
- The device is intended for indoor use.
- The device is only suitable for use in a dry environment.
- The device is designed to operate with its maximum load ranges.
**** Every household is a user of electrical and electronic equipment and
therefore a potential producer of hazardous waste to humans and the
environment from the presence of hazardous substances, mixtures and components
in the equipment. On the other hand, waste equipment is a valuable material,
from which we can recover raw materials such as copper, tin, glass, iron and
others. The symbol of a crossed-out rubbish bin placed on the equipment,
packaging or documents attached thereto indicates the necessity of separate
collection of waste electrical and electronic equipment. Products marked in
this way, under penalty of a fine, may not be disposed of in ordinary waste
together with other waste. The marking also means that the equipment was
placed on the market after the 13th August 2005. It is the user’s
responsibility to hand over the waste equipment to a designated collection
point for proper treatment.
Used equipment may also be returned to the seller in case of purchase of a new
product in a quantity not greater than the new purchased equipment of the same
type. Information about the available waste electrical equipment collection
system can be found at the information point of the shop and in the municipal
office. Proper handling of waste equipment prevents negative consequences for
the environment and human health!
INSTALLATION
DESCRIPTION
The modern set of two power sockets 2P+Z to be used under lockers, in lockers and in display cases.
INSTALLATION
The furniture socket shall be connected to the domestic mains system equipped with earthing. It is necessary to disconnect voltage of the mains where we connect the furniture socket. The lead-in wire is round with conductors of section 3×1.5 mm2 The lead-in cable has three conductors: yellow-green, blue and brown. At first, connect the earthing wire to the yellowgreen conductor, then connect the neutral wire to the blue conductor and finally, connect the live wire to the brown conductor. Step 1: Determine the place of installation and bring cables through the locker holes.
Step 2: Using a flat screwdriver, gently lever the front panel (fig. 2)
and then remove it (the dent is indicated where a screwdriver is to be put).
Step 3: Install the socket housing at the chosen placewith four screws
(fig. 3).
Step 4: After installation, align the sockets or the switch and put the
front panel on them by pressing it into the housing.
Step 5: Connect the round cable 3×1.5 mm2 to the domestic mains system.
Technical data
Nominal voltage: 230V~, 50Hz
Max. current: 16A
Max. load: 3680W
Number of sockets: 3
Number of USB ports: 2
USB charger output: 5VDC/2.1A
Standard of the socket: French (type E) – OR-GM9003, Schuko (type F) – OR-
GM-9003(GS)
Type of socket: 2P+E
Cable: 3×1.5 mm2 (0.6m)
Ingress protection: IP20
Protection class: I
Installation on normally combustible surfaces: YES
Installation on furniture surfaces: YES
Cleaning and maintenance
Protect the power leads against crushing, abrasion, excessive overbending and
another activities that can result in insulation damage.
Cleanse with a dry and clean cloth. Do not use any scrubbing agents or
solvents.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>