ORNO OR-WL-3200-100-HT Bathroom Fan Instruction Manual
- June 13, 2024
- ORNO
Table of Contents
Bathroom fan
OR-WL-3200/100/HT
OR-WL-3200/100/PS
OR-WL-3200/100/S
OR-WL-3200/100/TS| ORNO GROUP Sp. z.o.o.
ul. Rolnikow 437
44-141 Gliwice POLAND
tel. (+48) 32 43 43 110
---|---
OR-WL-3200-100-HT Bathroom Fan
IMPORTANT!
Before using the device, read this Service Manual and keep it for future
use. Any repair or modification carried out by yourselves results in loss of
guarantee. The manufacturer is not responsible for any damage that can result
from improper device installation or operation.
In view of the fact that the technical data are subject to continuous
modifications, the manufacturer reserves a right to make changes to the
product characteristics and to introduce different constructional solutions
without deterioration of the product parameters or functional quality.
Additional information and technical support related to the product is
available at: www.support.orno.pl. Orno Group
Sp. z 0.0. holds no responsibility for the results of non-compliance with the
provisions of the present Manual. Orno Group Sp. z 0.0. reserves the right to
make changes to the Manual – the latest version of the Manual can be
downloaded from www.support.orno.pl. Any
translation/interpretation rights and copyright in relation to this Manual are
reserved.
- The product is intended for indoor installation.
- Perform all operations with the power disconnected.
- Do not immerse the device in water or other liquids.
- Do not cover the device during operation.
- Do not open the device and do not make any repairs yourself.
- Do not use the device contrary to its intended use.
- The electrical installation requires a switch with a minimum 3mm distance between the contacts of all poles.
- Avoid the invers flow of gases into the room from an open chimney hole or other devices with the open fire.
Each household is a user of electrical and electronic equipment, and hence a
potential producer of hazardous waste for humans and the environment, due to
the presence of hazardous substances, mixtures and components in the
equipment. On the other hand, used equipment is valuable material from which
we can recover raw materials such as copper, tin, glass, iron and others. The
weee sign placed on the equipment, packaging or documents attached to it
indicates the need for selective collection of waste electrical and electronic
equipment.
Products so marked, under penalty of fine, cannot be thrown into ordinary
garbage along with other waste. The marking means at the same time that the
equipment was placed on the market after August 13, 2005. It is the
responsibility of the user to hand the used equipment to a designated
collection point for proper processing. Used equipment can also be handed over
to the seller, if one buys a new product in an amount not greater than the new
purchased equipment of the same type. Information on the available collection
system of waste electrical equipment can be found in the information desk of
the store and in the municipal office or district office. Proper handling of
used equipment prevents negative con sequences for the environment and human
health!
INSTALLATION
Grill disassembly
Mounting hole preparation
Fan installation
It is possible to set the fan operation parameters on the potentiometer with a
screwdriver in fans with electrical control system (models: OR-WL-3200/TS, OR-
WL-3200/HS).
Timer sensor (the fan operates from 3 to 23 minutes +/- 10% after switching
off the light)
Humidity sensor (the fan dries the room depending on chosen humidity level
from 40 to 80%)
WIRING SCHEME
L- Phase wire
N – Neutral wire
T – Control wire
M – Motor
– Humidity regulation
Time adjustment
L- Phase wire
N – Neutral wire
M – Motor
Grill assembly
TECHNICAL DATA
| Type | Bathroom fan |
|---|---|
| Installation | Wall |
| Diameter | Ø 100mm |
| Airflow | 93m³/h |
| Static pressure | 30Pa |
| Sound pressure | 26dB/1m |
| Nominal voltage | 230V~, 50Hz |
| Motor power | 8W |
| Rotarian speed | 2400rpm |
| Ingress protection | IP X2 |
| Bearing type | pan |
| Dimensions | 135x135x79mm |
| Net weight | 0,25kg |
DESCRIPTION
Useful bathroom fan that automatically draws the moist air to the outside. It is designed for wall mounting. A very quiet device that will take care of the air quality in the bathroom, but will not disturb our relaxation zone. The fan has a compact design and a short exhaust pipe, which will fit even in shallow ventilation ducts. High-class bearings guarantee a long service life of the device.
MAINTENANCE
The fan should be cleaned regularly and disassembled at least once a year for inspection of the motor and cleaning of the fan from deposits. The inspection includes cleaning, external visual inspection of the motor, starting and safety equipment.
- Make sure the unit is disconnected from the power source before cleaning.
- Plastic parts should be cleaned with a damp cloth or sponge with soap.
- After cleaning, ensure that any soap residue has been removed and that no liquids have entered the motor.
- Ensure that all components are dry before the fan is reassembled.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>