FEIT ELECTRIC T48 LED Light Bulb Direct Replacement Cool White Installation Guide

FEIT ELECTRIC T48 LED Light Bulb Direct Replacement Cool White

Safety Information

PLEASE READ THESE INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION.
THIS LAMP IS INTENDED TO WORK WITH THE EXISTING MAGNETIC AND ELECTRONIC BALLAST IN YOUR LIGHTING FIXTURE. THIS IS A PLUG AND PLAY LAMP, NO ELECTRICAL MODIFICATIONS ARE NEEDED.

This LED tube is intended to replace fluorescent tube lamps with ANSI designation F32T8 and F40T12 with G13 base.

This product may not be compatible with all ballasts. For more information about ballast compatibility please visitwww.Feit.Com.

1. Follow all safeguards stated in the manual, in addition to normal safety precautions in working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.

2. WARNING: RISK OF SHOCK: House electric current can cause painful shock or serious injury unless handed properly. For your safety, always remember to:
   A. Tum OFF the power supply at the fuse or circuit breaker box before you install the fixture.
   B. Ground the fixture to avoid potential electric shock and to ensure reliable starting.
   C. Double check all connections to be sure they are tight and correct.
   D. Wear rubber sole shoes and work on a sturdy ladder.
   E. Do not touch with wet hands.
   F. This device is not intended for use with emergency exits or emergency lights.
   G. Do not make or alter any open holes in the enclosure of wiring or electrical components during installation.

3. This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code

4. Avoid looking directly into the LED light.

5. WARNING: RISK OF CUTS: To prevent wiring damage, abrasion or cuts, do not expose wiring to edges of sheet metal or other sharp objects and wear gloves.

6. Account for small parts and destroy packaging material, as these may be hazardous to children.

| WARNING: Check the luminaire (fixture) carefully before installing the lamp. Ensure the electrical lamp holders (sockets) are not damaged and will make firm contact with the lamp pins.
---|---
| CAUTION: Risk of fire – If lamp or luminaire exhibit abnormal operation (buzzing, flickering, minimal or no light, etc.), immediately turn off power and contact us for more information.
---|---
| CAUTION: Risk of fire – Suitable for damp locations. Do not use with dimmers. Do not touch lamp pins to the metal housing when installing.
---|---
| WARNING: Do not install this in a pre-heat luminaire (fixture), often with external starters
---|---

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, Kvisit felt.com/contact-us for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANf IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

( 1) This device may not cause harmful interierence, and (2) this device must accept any interierence received, including interierence that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interierence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interierence to radio communications. However, there is no guarantee that interierence will not occur in a particular installation. If this equipment does cause harmful interierence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interierence by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information
Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA

THIS PRODUCT MAY NOT BE COMPATIBLE WITH ALL BALLASTS. FOR MORE INFORMATION ABOUT BALLAST COMPATIBILITY PLEASE VISITWWW.FEIT.COM.

Direct Replacement/Plug & Play Installation (Type A)

1. Turn off the power at the switch and fuse box or circuit breaker.

2. Remove existing fluorescent lamp(s) from the fixture. Replace with Feit Electric T48GROW/LED LED lamp
   

3. Turn on the power at the fuse box or circuit breaker and at the switch and enjoy your new Feit Electric LED lamp. 2 WWW.

SAVE THESE INSTRUCTIONS

Thank you for your purchase. Questions, comments
or feedback? We’d love to hear from you.
Visit feit.com/help for support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>