ORNO 13241335 Recessed Furniture Sockets Instruction Manual
- June 3, 2024
- ORNO
Table of Contents
13241335 Recessed Furniture Sockets
**Instruction Manual
**
Recessed Furniture Sockets
Before connecting and using the device, read this Operating Manual and keep it for future reference. In case something written herein is unclear, please contact the seller. Any repair or modification carried out by yourselves results in loss of guarantee. The manufacturer is not responsible for any damage that can result from improper device installation or operation. In view of the fact that the technical data are subject to continuous modifications, the manufacturer reserves a right to make changes to the product characteristics and to introduce different constructional solutions without deterioration of the product parameters or functional quality. Additional information about ORNO products and technical support are available at www.orno.pl. Orno-Logistic Sp. z o.o. holds no responsibility for the resultsof non-compliance with the provisions of the present Manual. Omo Logistic Sp. z o.o. reserves the right to make changes to the Manual – the latest version of the Manual can be downloaded from support.orno.pl.Any translation/interpretation rights and copyright in relation to this Manual are reserved.
- Disconnect power supply before any activities on the product.
- Do not immerse the device in water or other fluids.
- Do not operate the device when its housing or wire is damaged.
- Do not open the device and do not repair it by yourselves.
- Do not use the device contrary to its original purpose.
- Suitable for indoor use only.
- Keep out of reach of children.
- Avoid contact with water and other electric conductors (e.g. metals).
Please make sure that the power source (230 VAC) is disconnected before you start to install the device. Installation works can only be carried out by professional electricians with skill certificates issued accordingly to local health and safety regulations. Before you plug in the device, please make sure that electric circuit parameters comply with its technical specification. In case of wire damage, safely unplug it straight off. Do not use the device when its wire is damaged. It should be replaced by professional electrician.
INSTALLATION
- Before installing the device, drill a hole in the surface of a table or a desk.
- Once the hole is ready, press the button on the outer case in order to pull out a panel with sockets (1).
- Remove two screws at each side of the panel (2).
- Next, fasten the socket case to the surface of a table or desk with 4 screws. Make sure to properly place the wires (3).
- Put the screws back at each side of the panel and tighten them (4). Close the socket panel (5).
TECHNICAL DATA
Power source: 230v ∼, 50Hz
Rated load: 3600W
Max. current: 16A
Protection level: IP20
Power socket type: 2P+Z
Material: zinc alloy + steel plate
DESCRIPTION/MAINTENANCE
This device is suitable for indoor installation, inside standard desk/table holes. Any maintenance shall be carried out after the power source has been switched off. Clean with dry cloths only. Do not use chemical cleansers. This product has a grounding pin and current circuit protection.
Model:| No. of socket:| Socket type:| No. of USB
ports:| USB output:| Edge size:| Cable:| Cable length:| Additional
informations:| Net weight:
---|---|---|---|---|---|---|---|---|---
OR-AE-1335| 3| French (E type)| | | 7mm| | | | 1.32 kg
OR-AE-1338| 3| French (E type)| | | 7mm| yes| 1.5 m| | 1.60 kg
OR-AE-1371| 3| French (E type)| | | 2mm| | | | 1.40 kg
OR-AE-1371(GS)| 3| Schuko (F type)| | | 2mm| | | | 1.40 kg
OR-AE-1372| 3| French (E type)| | | 2mm| yes| 1.5 m| | 1.64 kg
OR-AE-1372(GS)| 3| Schuko (F type)| | | 2mm| yes| 1.5 m| | 1.66 kg
OR-AE-1336| 3| French (E type)| | | 2mm| | | | 1.29 kg
OR-AE-1336(GS)| 3| Schuko (F type)| | | 2mm| | | | 1.32 kg
OR-AE-1337| 3| French (E type)| | | 2mm| yes| 1.5 m| | 1.56 kg
OR-AE-1337(GS)| 3| Schuko (F type)| | | 2mm| yes| 1.5 m| | 1.51 kg
OR-AE-1337/3M| 3| French (E type)| | | 2mm| yes| 3 m| | 1.65 kg
OR-AE-1324| 2| French (E type)| 3| | 7mm| | | | 1.39 kg
OR-AE-13109| 2| French (E type)| 2| 5VDC / 2.1A| 2mm| | | | 1.28 kg
OR-AE-13109(GS)| 2| Schuko (F type)| 2| 5VDC / 2.1A| 2mm| | | | 1.3 kg
OR-AE-13126| 2| French (E type)| 2| 5VDC / 2.1A| 2mm| yes| 1.5 m| | 1.54 kg
OR-AE-13126(GS)| 2| Schuko (F type)| 2| 5VDC / 2.1A| 2mm| yes| 1.5 m| 2
network sockets| 1.63 kg
OR-AE-13126/3M| 2| French (E type)| 2| 5VDC / 2.1A| 2mm| yes| 3 m| 2 network
sockets| 1.40 kg
OR-AE-13125| 2| French (E type)| 2| 5VDC / 2.1 A| 2mm| yes| 1.5 m| anti-dust
brush, 2 network sockets| 1.40 kg
OR-AE-13125(GS)| 2| Schuko (F type)| 2| 5VDC / 2.1A| 2mm| yes| 1.5 m| anti-
dust brush, 2 network sockets| 1.42 kg
OR-AE-13127(GS)| 3| Schuko (F type)| | | 2mm| yes| 1.5 m| anti-dust brush|
1.42 kg
DIMENSONS
Every household is a user of electrical and electronic equipment and therefore a potential producer of hazardous waste to humans and the environment from the presence of hazardous substances, mixtures and components in the equipment. On the other hand, waste equipment is a valuable material, from which we can recover raw materials such as copper, tin, glass, iron and others. The symbol of a crossed-out rubbish bin placed on the equipment, packaging or documents attached thereto indicates the necessity of separate collection of waste electrical and electronic equipment. Products marked in this way, under penalty of a fine, may not be disposed of in ordinary waste together with other waste. The marking also means that the equipment was placed on the market after the 13th August 2005. It is the user’s responsibility to hand over the waste equipment to a designated collection point for proper treatment. Used equipment may also be returned to the seller in case of purchase of a new product in a quantity not greater than the new purchased equipment of the same type. Information about the available waste electrical equipment collection system can be found at the information point of the shop and in the municipal office. Proper handling of waste equipment prevents negative consequences for the environment and human health!
ORNO-LOGISTIC Sp. z o.o.
ul. Rolnikow 437, 44-141
Gliwice tel. 32 43 43 110
www.orno.pl