ORNO OR-MT-ME-1809 Wireless Outdoor Wi-Fi Camera Instruction Manual

: June 8, 2024
: ORNO

Table of Contents

ORNO OR-MT-ME-1809 Wireless Outdoor Wi-Fi Camera
DIRECTIONS FOR SAFTY USE!
CONSTRUCTION OF DEVICE
Operating and installation instructions
TECHNICAL DATA
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ORNO OR-MT-ME-1809 Wireless Outdoor Wi-Fi Camera

DIRECTIONS FOR SAFTY USE!

Before using the device, read this Service Manual and keep it for future use. Any repair or modification carried out by yourselves results in loss of guarantee. The manufacturer is not responsible for any damage that can result from improper device installation or operation.
In view of the fact that the technical data are subject to continuous modifications, the manufacturer reserves a right to make changes to the product characteristics and to introduce different constructional solutions without deterioration of the product parameters or functional quality.

Additional information about ORNO products are available at www.orno.pl. Orno-Logistic Sp. z o.o. holds no responsibility for the results of non-compliance with the provisions of the present Manual. Orno Logistic Sp. z o.o. reserves the right to make changes to the Manual – the latest version of the Manual can be downloaded from support.orno.pl. Any translation/interpretation rights and copyright in relation to this Manual are reserved.

Do not immerse the device in water or another fluid.
The product is intended for indoor and outdoor use.
Do not operate the device when its housing is damaged.
Do not open the device and do not repair it by yourselves.
Do not use the device contrary to its dedication.

Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for humans and the environment, due to the presence of hazardous substances, mixtures and components in the equipment. On the other hand, used equipment is valuable material from which we can recover raw materials such as copper, tin, glass, iron and others. The weee sign placed on the equipment, packaging or documents attached to it indicates the need for selective collection of waste electrical and electronic equipment. Products so marked, under penalty of fine, cannot be thrown into ordinary garbage along with other waste. The marking means at the same time that the equipment was placed on the market after August 13, 2005. It is the responsibility of the user to hand the used equipment to a designated collection point for proper processing. Used equipment can also be handed over to the seller, if one buys a new product in an amount not greater than the new purchased equipment of the same type. Information on the available collection system of waste electrical equipment can be found in the information desk of the store and in the municipal office or district office. Proper handling of used equipment prevents negative consequences for the environment and human health!

CONSTRUCTION OF DEVICE

IR LED
Twilight sensor
Camera lens
Indicator light
Microphone
PIR motion sensor
Loudspeaker
Mounting bracket Hole
ON/OFF
TF card slot
RESET button
USB socket C-type
IR LED (camera illumination) – it will turn on automatically when the ambient light is insufficient
Twilight sensor – when the ambient light is less than 2lux, the camera illumination will switch on,
Camera lens,
Indicator light – blue light flashes (pairing status), red light on (failed wi-fi connection), blue light on (connected successfully), red&blue light on (connecting wi-fi)
Microphone – captures sounds from the environment, enables a voice connection,
PIR motion sensor – when the device detects movement in its field of vision it will send a notification to the configured smartphone,
Mounting bracket holes – allows the device to be installed in the desired location.

Operating and installation instructions

DESCRIPTION AND USE

Wireless Full HD camera that communicates with the user’s smartphone thanks to a Wi-Fi connection. Just download a free Tuya application to view the recorded image in real time. The device has a place for a micro SD card (not included) that allows you to record video and a sensor that starts recording videos after motion has been detected. The camera has a built-in loudspeaker and a microphone and thanks to the Wi-Fi connection you can talk to a person standing in front of the camera. It has an additional backlight with IR LEDs, which provide a very clear image even after dark. Powered by a built-in, rechargeable battery, charged via USB. High resistance to weather conditions

PACKAGE LIST

After opening the package, make sure the product is unbroken and has all the accessories listed below:

Wireless camera
Mounting screws
BrackeBracket4.
USB charging cable
Waterproof plug – 2 pcs
Operating and installation guide guide

TECHNICAL DATA

Power supply: (2x 18650) 3.7V DC 5200mAh
Camera type: 1080p FHD sensor, 6 IR LEDs, mechanical IR-Cut iris
Resolution: 1920x1080p
Viewing angle: vertical 41°, horizontal 81°.
Memory card : Micro SD, max. 32GB, min. class. 10 (not supplied)
Connection standard: IEEE 802.11b/g/n
Ingress protection: IP65
Application: TUYA Smart
Standby power consumption : 120μA
Working power consumption: 170mA
Charging: USB charging cable (included) or solar panel (not included)
Material: plastic
Weight: 0.21kg
Dimensions: 55 x 102 x 55mm

INSTALLATION

Install the bracket on the wall using mounting screws provided.
Mount the device on the bracket. Make sure it is securely fastened.
Toggle the power ON/OFF to turn on/off the camera.
To charge your device, plug the charging cable into a USB-C socket and then connect the USB charger to the power supply. A solar panel (OR-MT-ME-1809PS)can also be connected to the device for solar charging.
To wake up the device from sleep mode, press and hold the RESET button on the back of the camera for about 5 seconds (the indicator LED should flash red).
Insert a MicroSD card with a maximum capacity of 32GB to store video (video is recorded in encrypted format for security reasons, preview of recorded files possiblevia the app).

PROBLEMS AND SOLUTIONS

The device cannot connect to a Wi-Fi network:
- Make sure that the wireless network to which the device is to be connected operates in the 2.4GHz standard.
The device is connected to a Wi-Fi network, but the phone does not receive any notifications:
- Make sure you have enabled your phone to receive notifications from the Tuya Smart app.
What power supply mode the device supports:
- The device is powered by 2x 18650 built-in rechargeable batteries (lithium batteries). The device can be charged via the included USB type C cable.

Free application to operate the device “Tuya Smart”

Installation

Users can download a free application to manage their device through scanning the QR code on the right, or by searching and downloading “Tuya Smart” application in the Apple App Store or Google Play. Once the application is installed, open it and go to the start page.
Register
If you do not already have an account with the app, click Sign up, you will be redirected to the next page. The system will automatically identify the country/region where you are from or you can manually select it yourself. Enter your email address, tick the privacy box and click Get verification code. Enter the code you receive, then enter your password and click Completed.
Add device
Click the “+” icon or Add device. Then select the “Video Surveillance” tab Wireless Camera (Wi-Fi). Make sure QR Code mode is selected in the upper right corner. Check the box below to make the Next button highlighted and click it.
Wi-Fi connection
To connect your device to a Wi-Fi network, select your network name in the app and enter the correct password. Press the “Next” button.
Device pairing
Your phone will display a QR code that you need to read with the camera (see the animation below the QR code). When you hear the sound from the camera, click the I heard the sound.
Device pairing
The application screen should display “Added successfully”, click the”Completed” button in the top right corner. The camera is ready to go, check the connection quality by running the camera preview.
Reset of device
Connect power to the camera, press and hold the RESET button for about 5 seconds. After a successful reset, the indicator LED should flash.
If the camera is added to an application, it must be deleted. To do this, select “Delete device” in the camera settings.