Tenda Desktop Switch Installation Guide
- June 7, 2024
- Tenda
Table of Contents
Tenda Desktop Switch Installation Guide
TEF1109D
Package contents
- Switch * 1
- Power adapter * 1
- Quick installation guide * 1
If any item is missing, damaged or incorrect, please keep the original packaging and contact the local reseller or distributor immediately.
Connect your devices
Example: TEF1109D
Tip:
- All ports of your switch support the auto MDI/MDIX function, indicating that either straight cable or crossover cable is acceptable to connect your switch to Ethernet devices.
- To protect your switch from lightning damage, connect the grounding terminal of the switch to a grounding cable.
Specifications
Model|
TEF1109D
|
TEF1109DT
---|---|---
Standards|
IEEE 802.3, IEEE 802.3u, IEEE 802.3x
|
IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3ab
10/100 Mbps RJ45 Port|
Port 1 – 9
|
Port 1 – 8
10/100/1000 Mbps RJ45 Port|
/
|
Port 9
Working mode| VLAN off, VLAN on
Switching capacity|
1.8 Gbps
|
3.6 Gbps
Store-and-forward|
Supported
Auto learning & auto aging|
Supported
MAC address table|
2 K
Dimension|
140.2 mm 66.2 mm 25.2 mm
Power supply|
- Input: 100-240 V AC, 50/60 Hz, 0.3 A
- Output: 9 V DC, 0.6 A
Lightning protection|
6 kV for port 9
Operating environment|
- Temperature: (0 – 40) °C
- Humidity: (10 – 90) % RH, non-condensing
Storage environment|
- Temperature: (-40 – 70) °C
- Humidity: (5 – 90) % RH, non-condensing
Transmission rate|
- Ethernet: 10 Mbps (half duplex) / 20 Mbps (full duplex) Fast
- Ethernet: 100 Mbps (half duplex) / 200 Mbps (full duplex)
/
| Gigabit Ethernet: 2000 Mbps (full duplex)
Transmission media|
- Ethernet: CAT3 UTP/STP cable or better
- Fast Ethernet: CAT5 UTP/STP cable or better
/
| Gigabit Ethernet: CAT5e or CAT6 UTP/STP cable (recommended)
LED indicators
LED indicator|
Status
|
Description
---|---|---
|
Solid on
| The switch is connected to a power resource properly.
Off
| The switch is disconnected or not properly connected to a power resource.
1-9
|
Solid on
| The port is connected properly.
Blinking
| Data is being transmitted over the port.
Off
| The port is disconnected or improperly connected.
Working mode introduction
The switch has two modes: VLAN off and VLAN on. Use the slide switch to set the switch to your required mode according to the following descriptions.
VLAN off: Default mode of the switch. In this mode, all ports can communicate with each other.
VLAN on: In this mode, ports 1 to 8 of TEF1109D/TEF1109DT can communicate with port 9 but cannot communicate with each other. You can enable this mode to reduce broadcast storm and isolate DHCP broadcast.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Caution:
- Adapter Model: BN049-A05009E/BN049-A05009B
- Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
- Input: 100 – 240 V AC 50/60 Hz, 0.3 A
- Output: 9 V 600 mA
- : DC Voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
The mains plug is used as disconnect device; the disconnect device shall
remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Copyright
Copyright © 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co.,
Ltd. Other brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders. Specifications are subject
to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan
District, Shenzhen, China. 518052
Canada hotline: 1-888-998-8966
Hong Kong hotline: 00852-81931998
Website: http://www.tendacn.com
E-mail: support@tenda.com.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>