Tenda CT Series Outdoor Wi-Fi Camera 2K Installation Guide
- June 1, 2024
- Tenda
Table of Contents
Tenda CT Series Outdoor Wi-Fi Camera 2K
Appearance
The camera appearance varies with models. Please refer to the camera you purchased.
①| Ethernet port| 10/100 Mbps auto-negotiation Ethernet port, used
for connecting such devices as the router and switch.
---|---|---
②| Power jack| Used to connect to the included power adapter.
③| Speaker| /
④ ⑤| Fill light| /
⑥
|
LED indicator
| Solid red : Initializing and starting.
Blinking red slowly : Disconnected from the network.
Blinking red quickly : Connecting to the network.
Solid blue : Connected to the network.
Blinking blue slowly : Upgrading.
Blinking blue quickly : Waiting to connect to the network.
⑦| Microphone| /
⑧| Micro SD card slot
( Behind the cover )
| Insert the Micro SD card to store the monitoring videos.
⑨
| Reset button
( Behind the cover )
| Hold down the reset button for about 5 seconds and release it after the LED
indicator blinks blue quickly or you hear a prompt tone. The camera is reset
to factory settings successfully.
⑩| Orientation knob
( if any )
| Adjust the monitoring angle for the best view through your camera.
Add the camera to TDSEE App
Tips: Before adding your camera, ensure that the router is connected to the internet successfully and the filter function is disabled.
-
Power on the camera.
The LED indicator lights solid red after the camera is powered on. When the LED indicator blinks blue quickly, the camera is waiting to connect to a 2.4 GHz Wi-Fi network. -
Download the TDSEE App onto your mobile device by scanning the QR code or searching for TDSEE in the Google Play or App Store.
-
Run the TDSEE App and follow the instructions to complete user registration. Enter the homepage, and tap Add a device or in the upper-right corner of the homepage.
-
Scan the QR code on the top of the camera, and follow the instructions in the App.
After the settings are completed, you can see that the added camera is online on the homepage of the TDSEE App, and the camera has been managed by the TDSEE App.
Install the camera
Tips
- Make sure the ceiling is strong enough to withstand three times the weight of the camera.
- You may need a hammer drill, a drill bit (Diameter: 6 mm), a screwdriver, and a ladder for the installation.
Ceiling/wall mounting
- Place the template at the desired location.
- Drill screw holes and insert anchors into them. (Drill bit diameter: 6 mm; Hole depth: 28-32 mm)
- Fix the bracket (if any) to the desired location.
- Fix the camera using the screws.
Pole mounting
You can use this method if the bracket is provided.
- Pass the strap (self-prepared) through the holes in the bracket, and secure the bracket to the pole.
- Fix the camera using the screws.
Adjust the monitoring angle
Loosen the orientation knob (if any), adjust the orientation of the camera as
required, then tighten the knob.
Install the waterproof kit
Tips : The included waterproof kit is not suitable for the Ethernet cable with protection cover on the crystal head. See the example on the right.
You can install the waterproof kit and wrap the end with waterproof tape for the Ethernet port as required. When you connect the Ethernet cable to the Ethernet port of the camera, the waterproof kit installation steps are as follows.
Power on the camera
Power on the camera after the camera is mounted. When the camera completes
startup, it will automatically connect to the configured Wi-Fi network. When
the LED indicator of the camera is solid blue, you can use the camera
normally.
Log in to the web UI of the camera
After the camera works properly, you can manage the camera through TDSEE App
or web UI (Some models of cameras support). (Please scan the QR code of Get
support and services in this guide to obtain the related user guide.)
To log in to the web UI:
-
Connect the computer to the router that is connected to the camera.
-
Set the IP address of the computer to an unused one belonging to the same network segment as the IP address of the camera but different from the IP address of the camera.
By default, the login IP address of the camera is 192.168.1.203, and the DHCP function is enabled. If there is a DHCP server in the network, the IP address of the camera may be changed. Please refer to the actual IP address assigned to the camera by the DHCP server. -
Start a browser and enter the IP address of the camera in the address bar to access the login page. Enter the Login Username (default: admin) and Login Password (default: admin123456), then click Login.
Tips : For network security, after you log in to the web UI, please modify your password in time.
After successful login, you can start to configure the camera as required.
FAQ
Q1: What should I do if I failed to add the camera?
A1 : Try the following solutions:
- Ensure that the router is connected to the internet successfully.
- The camera only supports 2.4 GHz Wi-Fi network. When adding the camera, you need to connect the smartphone to a 2.4 GHz Wi-Fi network.
- Do not hide the Wi-Fi network of the router when adding the camera (After the camera is added successfully, you can hide the Wi-Fi network).
- Confirm whether the LED indicator of the camera blinks blue quickly. If not, please reset the camera and configure it again.
- Reset method: Hold down the Reset button for about 5 seconds and release it when the LED indicator blinks blue quickly or you hear a prompt tone. The camera is reset successfully.
Q2: What should I do when the video preview is not smooth?
A2 : Try the following solutions:
- Check if the Wi-Fi network of the router is smooth.
- Take the router closer to the camera and adjust the antenna angle of the camera to be vertical.
- When previewing the video with cellular mobile data, make sure that the internet connection of the smartphone is smooth.
- Auto (if supported), Fluent and HD are supported for video preview. You can switch the video clarity according to the internet status.
Q3: How to store the video?
A3 : Try the following solutions:
- Method 1 : Install the micro SD card to the camera. The recording mode of the Micro SD card supports Alarm Recording and All Day Recording. By default, the recording mode is Alarm Recording, you can modify the recording mode according to the actual conditions.
- Method 2 : Subscribe to the Cloud Storage Service on TDSEE App. Procedure: Run the TDSEE App, choose the camera on the homepage, then tap Cloud in the lower left corner. You can enjoy free cloud storage service (7-days continuous detection recording) for 3 months upon the first activation.
- Method 3: Connect the camera to the NVR. The camera supports the ONVIF protocol and can be added to the NVR either wired or wireless method for recording storage. The default user name and password of the camera are admin and admin123456 respectively, you can change the default password on the web UI (some models of cameras support). The specific configuration method of the NVR is subject to the manufacturer’s instructions.
Q4: How to get full-color monitoring video through the camera no matter in the daytime or at night?
A4 : Set Night Vision Mode of the camera to Full-color Mode.
- Method : Run the TDSEE App, choose the camera on the homepage, then tap Settings ( in the upper right corner) > Night Vision Mode, and choose Full-color Mode.
Q5. How to view the videos stored in the Micro SD card of the camera on the
computer?
A5 : If you remove the Micro SD card installed in the camera and view the
videos from your computer, it is recommended to use VLC media player or
Potplayer to play the videos.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>