PANDUIT PSL-MLD Multiple Lockout Device with PSL-MLDC Durable Cable Installation Guide

PANDUIT PSL-MLD Multiple Lockout Device with PSL-MLDC Durable Cable

Installation Guide

PSL-MLDC Durable Cable for Multiple  Lockout Device

Prevents inadvertent, accidental or unintentional energization of gate valves and the electrical circuit for disconnect switches. Immobilizes large and cumbersome devices. May be used as a
hasp (6 lock maximum) – No Installation Tools Required

Installation Instructions for PSL-MLD used as gate valve lockout device

Step 1:

Verify valve is de-energized. Thread end of cable through gate valve handle and then through loophole of cable.

Step 2:

With loophole tight against the gate valve and lockout open, continue threading end of cable through thepre-notched opening of lockout device

Step 3:

Cinch up plastic lockout body onto cable, forming a secure bond.

Step 4:

Insert up to six padlocks and tags into holes of the hasp. Verify that the lockout device secures the gate valve in a safe or off position.

Installation Instructions for PSL-MLD used as a disconnect switch lockout

device

Step 1:

Verify disconnect is de-energized. Thread cable through holes on each disconnect handle. Insert end of cable through loophole and tightly hold firm near lockout point.

Step 2:

Thread end of cable through prenotched opening of lockout device.

Step 3:

Cinch up plastic lockout body onto cable, forming a secure bond.

Step 4:

Insert up to six padlocks and tags into holes of the hasp. Verify that the lockout device secures the disconnect switches in a safe or off position.

Instructions and photos demonstrate installation with the loop hole of the cable. User shall determine if threading the cable in both the top hole and pre-notched opening better secures the energy isolating
device in a safe or off position.

•  The PSL-MLD accommodates Panduit PSL-6, PSL-7, PSL-8 padlock series (0.3” shackle diameter maximum)
• The PSL-MLDC six foot coated galvanized steel cable may be purchased seperately. For extended cable lengths order 200 foot cable, cable crimps, and crimp tool (PSL-MLDC200, PSL-MLD-CRIMP, and PSL-MLD-TOOL) .GMPSL-INMLD

Ask for these additional lockout products at your local Panduit

Distributor

Circuit breaker lockout de vice (PSL-CB, PSL-CBIL, PSL-CBL, PSL-CBNT, PSL- CBILNT) Wall Switch Lockout Devices (PSL-WS, PSL-WS1A) Plug Lockout Devices (PSL-P, PSL-CL110, PSL-CL480)
Lockout Kits( PSL-PK-EA, PSL-KT-CONA, PSL-KT-MROA, PSLPK- EAKS) Lockout Training Video Program Gate Valve Lockout Devices (PSL-V in Multiple Colors and Sizes) Ball Valve Lockout Devices (PSL-BV1, PLS-BV2, PSL-BV3, and PSL-BFV) Padlocks (PSL-6, PSL-7, PSL-8 in Multiple Colors and Shackle lenghts.) Safety Signs and Tags

Installation Procedure Warning!

Always perform an Electrical De-Energization Test and a Blocking verification Test before using this product.

ELECTRICAL DE-ENERGIZATION TEST:

All associated circuitry and/or energy isolating devices should be electrically verified as de-energized prior to and following the installation of the lockout device.

BLOCKING VERIFICATION TEST:

If this lockout device cannot be affixed in a manner that will hold the appropriate energy isolating devices in a safe or off position, the devices SHALL NOT be used. APPROPRIATE USE of these lockout devices is the sole responsibility of the user in relation to compliance with OSHA’s Lockout/Tagout regulations Before using this product, user shall determine the suitability of the product for his intended use. User assumes all risk and liability whatsoever in connection with the installation of this product.

PANDUITDISCLAIMS ALL LIABILITY FOR ANY INJURY, LOSS OR DAMAGE, WHETHER DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE INSTALLATION AND USE OF THE PRODUCT.

• Our products are warranted to be free from defects in material and workmanship at the time of sale but our obligation under this warranty is limited to the replacement of any product proved to be defective within six months (for product) or 90 days (for tools) from the date of delivery. Tool warranty is void if Panduit tools are modified, altered or misused in any way. Use of Panduit tooling with any product other than the specified Panduit products for which the tool was designed, constitutes misuse. Before using, user shall determine the suitability of the product for his intended use and user assumes all risk and liability whatsoever in
  connection therewith. This warranty is made in lieu of and excludes all other warranties, expressed or implied. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE SPECIFICALLY EXCLUDED. Neither seller nor manufacturer shall be liable for any other injury, loss, or damage whether direct or consequential arising out of the use of or the inability to use the product.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>