PANDUIT LCCF8 Copper Compression Connectors Instruction Manual
- June 1, 2024
- PANDUIT
Table of Contents
PANDUIT LCCF8 Copper Compression Connectors
COPPER COMPRESSION CONNECTOR INSTALLATION
-
Use a connector marked for the wire size and wire material to be used. NEVER use a copper connector on aluminum wire.
-
Strip wire insulation to the approximate length shown on tool chart. DO NOT nick or ring the conductor strands.
-
Clean the wire.
-
Insert stripped wire into the connector until the wire stops.
-
Using the installation tooling shown on other side, insert the connector in die and crimp between color bands or knurl markings, use these markings as a guide to evenly space crimps on barrel of connector. Begin crimping near the tongue end of the lug and continue crimping toward the wire end.
REQUIRED NUMBER OF COMPRESSIONS SHOWN ON TOOL CHART IN ( ). -
After crimping, inspect for sharp edges, flash or burrs and remove if present.
HEAT SHRINK INSULATION INSTRUCTION
- Refer to Panduit catalog or www.panduit.com for heat shrink material information, tubing size, voltage rating, and shrink temperature.
- Cut tubing to length allowing insulation coverage as desired. Allow a minimum of 1-1/2″ inch overlap on wire insulation.
- Shrink with a standard propane torch or heat gun. MOVING FROM CRIMPED PORTION OF CONNECTOR TOWARD INSULATED WIRE. Adhesive flow at the ends indicates total shrinkage complete.
Heat shrink insulation and blank tongues not tested by TELECORDIA
INSTALLATION INSTRUCTIONS
Panduit Part Number
| ****
Std. Wire Size AWG
| ****
Cable Classes
| ****
Wire Strip Length (In.)
| A
See Tool List Below
---|---|---|---|---
Die Part Number/Color Code and Die Index Number/ (Number of Crimps)
L=Lug S= Splice| For LCAF,
SCSF Parts
| For LCCF
Parts
LCCF8 LCAF8| ****
8 AWG
| ****
Locomotive (DLO)
| ****
13/16
| CD-920-8
Red P21 (1)
SCSF8| 11/16
LCAF6| ****
6 AWG
| ****
K,M,
Locomotive (DLO)
| 7/8| ****
CD-920-6
Blue P24 (1)
| ****
CD-920-6
Blue P24 (2)
LCCF6| 1-5/16
SCSF6| 13/16
LCAF4| ****
4 AWG
| ****
K,M,
Locomotive (DLO)
| 7/8| ****
CD-920-4
Gray P29 (1)
| ****
CD-920-4
Gray P29 (2)
LCCF4| 1-5/16
SCSF4| 13/16
LCAF2| ****
2 AWG
| ****
K,M,
Locomotive (DLO)
| 15/16| ****
CD-920-2
Brown P33 (1)
| ****
CD-920-2
Brown P33 (2)
LCCF2| 1-7/16
SCSF2| 7/8
LCAF1| ****
1 AWG
| ****
K,M,
Locomotive (DLO)
| 1| ****
CD-920-1/0
Pink P42 (1)
| ****
CD-920-1/0
Pink P42 (2)
LCCF1| 1-1/2
SCSF1| 7/8
LCAF1/0| ****
1/0 AWG
| ****
K,M,
Locomotive (DLO)
| 1-7/16| ****
CD-920-2/0
Black P45 (2)
LCCF1/0| 1-9/16
SCSF1/0| 1-3/16
LCAF2/0| ****
2/0 AWG
| ****
K,M,
Locomotive (DLO)
| 1-7/16| ****
CD-920-3/0
Orange P50 (2)
LCCF2/0| 1-9/16
SCSF2/0| 1-3/16
LCAF3/0| ****
3/0 AWG
| ****
K,M,
Locomotive (DLO)
| 1-7/16| ****
CD-920-4/0
Purple P54 (2)
LCCF3/0| 1-5/8
SCSF3/0| 1-3/16
LCAF4/0| ****
4/0 AWG
| ****
K,M,
Locomotive (DLO)
| 1-7/16| ****
CD-920-250
Yellow P62 (2)
LCCF4/0| 1-11/16
SCSF4/0| 1-3/16
CD-920 dies can be used with CT-940CH and CT-2940 series tools with die adapter
- CT-920, CT-920/CV, CT-920CH, CT-920CH/CV, CT-920CH/CCP, CT-930, CT-930CH, CT-940CH①,
- CT-2920, CT-2920/CCP, CT-2920/CCPINT, CT-2920/CCPUK, CT-2920/CCPAUS, CT-2920/CCPTO,
- CT-2930, CT-2930/L, CT2930/LE, CT-2931, CT-2931/ST, CT-2931/STINT, CT-2931/STUK, CT-2931/STAUS,
- CT-2931/TO, CT-2931/STCV, CT-2931/STCVINT, CT-2931/STCVUK, CT-2931/STCVAUS, CT-2931/CVTO,
- CT-2940➀, CT-2940/L➀, CT-2940/LE➀, CT-2940/ST➀, CT-2940/STINT➀, CT-2940/STUK➀, CT-2940/STAUS➀, CT-2940/TO➀
Panduit Part Number
| ****
Std. Wire Size AWG
| ****
Cable Classes
| ****
Wire Strip Length (In.)
| A
See Tool List Below
---|---|---|---|---
Die Part Number/Color Code and Die Index
Number/ (Number of Crimps)
L=Lug S= Splice| ****
For LCAF, SCSF Parts
| ****
For LCCF Parts
LCAF250
| ****
250 kcmil
262.6 kcmil
| ****
K,M,
Locomotive (DLO)
| ****
1-3/4
| ****
CD-920-300
White P66 (2)
| ****
CD-920-300
White P66 (3)
LCCF250| 2-5/16
SCSF250| 1-3/16
LCAF300
| ****
300 kcmil
313.1 kcmil
| ****
K,M,
Locomotive (DLO)
| ****
1-3/4
| ****
CD-920-350
Red P71 (2)
| ****
CD-920-350
Red P71 (3)
LCCF300| 2-3/8
SCSF300| 1-1/4
LCAF350
| ****
350 kcmil
373.7 kcmil
| ****
K,M,
Locomotive (DLO)
| ****
1-15/16
| ****
CD-920-400
Blue P76 (2)
| ****
CD-920-400
Blue P76 (3)
LCCF350| 2-9/16
SCSF350| 1-1/2
LCAF400
| ****
400 kcmil
444.4 kcmil
| ****
K,M,
Locomotive (DLO)
| ****
2-1/4
| ****
CD-920-500
Brown P87 (2)
| ****
CD-920-500
Brown P87 (3)
LCCF400| 2-3/4
SCSF400| 1-11/16
LCAF500
| ****
500 kcmil
535.3 kcmil
| ****
K,M,
Locomotive (DLO)
| ****
2-5/16
| ****
CD-920-500A
Pink P99 (2)
| ****
CD-920-500A
Pink P99 (3)
LCCF500| 2-15/16
SCSF500| 1-5/8
LCAF600➂| ****
646.4 kcmil
| ****
Locomotive (DLO)
| 2-3/8| ****
CD-920-750
Black P106 (2)
| ****
CD-920-750
Black P106 (3)
LCCF600➂| 3
SCSF600➂| 1-5/8
LCAF750➂| ****
777.7 kcmil
| ****
Locomotive (DLO)
| ****
2-7/16
| ****
CD-940-800➂
Orange P107 (2)
| ****
CD-940-800➂
Orange P107 (4)
LCCF750➂| 3-1/16
SCSF750➂| 1-5/8
CD-920 dies can be used with CT-940CH and CT-2940 tools with die adapter.
CD-940 dies to be used exclusively with CT-940CH and CT-2940 series tools.
Can only be crimped with CT-940CH and CT-2940 tools.
- CT-920, CT-920/CV, CT-920CH, CT-920CH/CV, CT-920CH/CCP, CT-930, CT-930CH, CT-940CH➀,
- CT-2920, CT-2920/CCP, CT-2920/CCPINT, CT-2920/CCPUK, CT-2920/CCPAUS, CT-2920/CCPTO,
- CT-2930, CT-2930/L, CT2930/LE, CT-2931, CT-2931/ST, CT-2931/STINT, CT-2931/STUK, CT-2931/STAUS,
- CT-2931/TO, CT-2931/STCV, CT-2931/STCVINT, CT-2931/STCVUK, CT-2931/STCVAUS, CT-2931/CVTO,
- CT-2940➀, CT-2940/L➀, CT-2940/LE➀, CT-2940/ST➀, CT-2940/STINT➀, CT-2940/STUK➀, CT-2940/STAUS➀, CT-2940/TO➀
For Instructions in Local Languages and Technical Support:
techsupport@panduit.com
E-mail:
cs@panduit.com
Phone:
800-777-3300
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>