ZEVNI A04859C3 Jugal 12 Inch Wide Black Seeded Glass Ceiling Light Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
A04859C3 Jugal 12 Inch Wide Black Seeded Glass Ceiling Light
Instruction Manual
A04859C3 Jugal 12 Inch Wide Black Seeded Glass Ceiling Light
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING:
(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Socket (3)
(G) Knob nut (2)
(H) Tube (1)
(I) Glass shade (1)
(J) Plastic washer (1)
(K) Iron washer (1)
(L) Hex nut (2)
(M) Flat cover (1)
(N) Flat nut (1)
OUTLET BOX
ACCESSORIES & QTY ENCLOSED:
(A) Plastic wire connector (3)
(B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
● Unscrew knob nuts (G) from mounting plate (C).
● Set them aside for later installation. -
● Pass the fixture wires through tube (H) and canopy (E).
● Screw tube (H) onto canopy (E) as shown in the illustration. -
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
● Carefully pass the supply wires through mounting plate (C).
● Secure mounting plate (C) to the outlet box with mounting screws (B).
NOTE: the side of mounting plate (C) marked “GND” must face out. -
Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart Connect wires according to the below chart
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
Black | White |
*Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other
than green) with silver conductor
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) • Twist wires together with plastic wire connectors until tightly joined.
• Wrap each connector with approved electrical tape.
• Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.-
● Raise canopy (E) over the outlet box.
● Align canopy (E) with the pre-assembled mounting screws.
● Secure canopy (E) with the previously removed knob nuts (G) till snug.
Note: canopy (E) should be snug against the ceiling and knob nuts (G).
If not, adjust the threaded length on mounting plate assembly (C):
• Unscrew the pre-assembled hex nuts.
• Screw the pre-assembled screws in or out of mounting plate (C).
• When the secure length is achieved, tighten the hex nuts and back to step 7. -
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
- Carefully let tube (H) pass through glass shade (I), plastic washer (J) and iron washer (K).
- Tighten hex nut (L) onto tube (H) to secure glass shade(I).
- Carefully let tube (H) pass through flat cover (M).
- Tighten flat nut (N) onto tube (H) to secure flat cover (M).
Note: glass shade (I) should be snug against canopy (E) and flat cover (M).
If not, adjust the threaded length in tube (H):
• Remove glass shade (I), plastic washer (J), iron washer (K) and hex nut (L).
• Screw the threaded pipe in or out of tube (H), then tighten another hex nut (L) as shown in the illustration.
• When the secure length is achieved, return to step 2).
- Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you needto order replacement parts. All parts for this fixture canbe ordered from the place of purchase. Be sure to useexact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glasswith a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouringpads or powders, steel wool or abrasive paper.
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com
Documents / Resources
|
ZEVNI A04859C3 Jugal 12 Inch Wide Black Seeded Glass Ceiling
Light
[pdf] Instruction Manual
A04859C3 Jugal 12 Inch Wide Black Seeded Glass Ceiling Light, A04859C3, Jugal
12 Inch Wide Black Seeded Glass Ceiling Light, Jugal Ceiling Light, 12 Inch
Wide Black Seeded Glass Ceiling Light, Ceiling Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>