POLAR Display Cooler Instruction Manual

POLAR Display Cooler Instruction Manual

Safety Tips

• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components or service panels on this product.
• Consult Local and National Standards to comply with the following:
  • Health and Safety at Work Legislation
  •  BS EN Codes of Practice
  • Fire Precautions
  •  IEE Wiring Regulations
  •  Building Regulations
•  DO NOT immerse in water, or use steam/jet washers to clean the unit.
•  DO NOT cover the appliance when it is operating.
•  Always carry, store and handle the appliance in a vertical position.
•  Never tilt the appliance more than 45° from the vertical.
•  Not suitable for outdoor use.
•  Keep all packaging away from children. Dispose of the packaging in   accordance with the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a POLAR agent or a recommended qualified technician in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Polar recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing
• Polar recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Warning: Risk of Fire / flammable materials

• The refrigerant gas contained in this appliance is isobutene (R600a), which is low-polluting but flammable.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance

Warning : Keep all ventilation openings clear of obstruction. Unit should not be boxed in without adequate ventilation.

• Warning: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are the type recommended by the manufacture.

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your POLAR product.

Pack Contents

The following is included:

• Display Chiller
• Instruction manual
  POLAR prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your POLAR dealer immediately.

Installation

Note : If the unit has not been stored or moved in an upright position, let it stand upright for approximately 12 hours before operation. If in doubt allow to stand.

1. Remove the appliance from the packaging and the protective film from all surfaces.

2. Avoid positioning the cooler in direct sunlight or damp areas.

3. To optimize performance and longevity, ensure a minimum clearance of 2.5cm is maintained between the unit and walls and other objects, with a minimum 5cm clearance on the top. NEVER LOCATE
   NEXT TO A HEAT SOURCE.

4. If necessary, adjust the screw legs of the cooler to make it level.

WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

Reversing the Door

Depending on the location of the appliance, it may be necessary to change the direction the door of the cooler opens by changing the side of the door handle.

To reverse the door handle:

1. Ensure the appliance is disconnected from the power supply.
2. Tilt the appliance back slightly and prop it securely. The appliance must not be tipped back by more than 45 degrees.
3. Unscrew the door hinge screws on the base of the door and remove the Hinge.
4. Open the door slightly and remove the door in a downwards direction.
5.  Remove the plastic screw cover from the top of the cooler by levering it off with a small screwdriver.
6. Unscrew and remove the hinge from the top of the appliance.
7.  Screw the reversed door frame Hinge to the opposite side of the appliance and reattach the screw cover.
8. Fit the door into place by locating the upper Hinge first then closing the door.
9. Reattach the Bottom hinge onto the opposite side of the door. 10. The appliance can now be lowered into position. .
10. The appliance can now be lowered into position.

Operation

Controller
The controller is located inside the cabinet. These models have an integrated light that can be switched on using the switch on the controller.
The thermostat is graded from 0 (warm) to 7 (cold).

• The display Cooler is recommended to be set at temperature 4°C.
• This appliance is intended to operate in climates where the maximum temperature and humidity are 25°C and 60% respectively.
• Please refer to the following table to select the suitable temperature setting.

The chart below indicates the ideal storage temperatures for different types of food and beverage:

Note : Setting the temperature too high can cause the wine to spoil, and setting the temperature too low can waste electricity.

Cleaning, Care & Maintenance

• Always switch off and disconnect the power supply before cleaning.
• Warm, soapy water is recommended for cleaning. Cleaning agents may leave harmful residues.
• A POLAR agent or qualified technician should carry out repairs if required.
• Periodically clean the bottom of the cooler compartment to remove any build-up of condensation.

Troubleshooting

If your POLAR appliance develops a fault, please check the following table before making a call to the Helpline or your POLAR dealer.

plugged in correctly and switched on
Plug or lead is damaged| Call POLAR agent or qualified Technician
Fuse in the plug has blown| Replace the fuse
Power supply| Check power supply
Appliance is noisy or works intermittently| Appliance is not level| Adjust the feet to level the appliance
Cooler cabinet is not cold enough| Temperature set incorrectly| Check temperature and reset if necessary
External environment may require colder temperature| Check temperature and reset if necessary
The door is opened too often| Only open when necessary
Door seal is worn| Call POLAR agent or qualified technician
The light does not work| Bulb has blown| Replace bulb
Light switch set to Off| Set light switch to On
Doors will not close properly| Cooler is not level| Adjust the feet
Door has been reversed and not properly fitted| See “Reversing the Door”
Shelves are out of position| Check all shelves are properly inserted
Door seal is dirty| Wipe clean with a damp cloth

Technical Specifications

Model| Voltage| Power| Current| Refrigerant| Temp. Range| Dimensions H x W x D mm| Weight (kg)
---|---|---|---|---|---|---|---
CF750| 220-240V

50Hz

| 85W| 0.55A| R600a| 1-12°C| 825 x 430 x 480| 26

Electrical Wiring

POLAR appliances are supplied with a 3 pin BS1363 plug and lead.

The plug is to be connected to a suitable mains socket.

POLAR appliances are wired as follows

• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed .

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Disposal

EU regulations require refrigeration product to be disposed of by specialist companies who remove or recycle all gasses, metal and plastic components.

Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of the equipment locally.

Alternatively call the POLAR helpline for details of national disposal companies within the EU.

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

POLAR parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

POLAR products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR  Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to change specifications without notice.

References

• Polar Refrigeration - Commercial Refrigeration

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>