Airmax Color Changing RGBW LED Light Sets Owner’s Manual

Airmax Color Changing RGBW LED Light Sets Owner’s Manual

THANK YOU FOR CHOOSING The Airmax Color-Changing RGBW LED Light Set

Airmax® Color-Changing RGBW LED Light Set

Important Safety Instructions

• Under NO circumstances should anyone enter the water with the electrical equipment plugged in and/or in operation
• WARNING – Risk of electric shock – This light set is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle. This light set has not been investigated for use in swimming pool areas.
• ALWAYS use a GFCI protected receptacle or breaker.
• NEVER lift or drag the light set by the power cord.
• During freezing temperatures, remove and store inside.
• If installing from a boat or raft ALWAYS wear a Life Guard approved personal flotation device.
• ALWAYS use a qualified electrician when installing a power source next to your pond.

Setup & Installation

Installing the Airmax LED Light Set

1. To attach the light, clip the light into the inner mounting positions on the float and use the vertical tension screw to secure the light into place. Continue until all lights are attached.
2. After attaching the Airmax LED Light Set to the float, connect the quick disconnect end to the power cord.
3. Attach the light set power cord strain relief on to one of the loops underneath the float mount ring.
4. Adjust the lights to point in the desired direction.
5. Connect the light set’s power cord into the control panel or other GFCI outlet.

RGBW Remote Control Instructions

The Airmax Color-Changing RGBW LED Light Set is run by a wireless remote with a range of up to 200ft. The wireless remote allows you to change the color, dim/brighten the lights, control flash speed and run up to 9 preset programs.
Your wireless remote has already been paired for your light set on Zone 1.
Requires: 2 AAA Batteries(Included).

Basic Control Functions

• Press and Hold Master ON or ZONE ON for several seconds to turn all lights to white mode.
• Touch the color ring to adjustment lights to any color.
• While in white or solid color mode, use the speed buttons to change the tone from cool to warm white or vibrant to pastel colors.
• Change the brightness by using the brightness slide ring.
• Adjust flash speed for any preset program using the speed buttons.

Preset Programs/Modes

Press the “M” Mode button to scroll through the pre-programmed light settings:

Program 1 – RGBW Fade In/Fade Out
Fades in and fades out the color red, green, blue and white one after another.

Program 2 – Color Flash
Red, green, blue, white, yellow and purple flashes.

Program 3 – Disco
Multiple colors strobe and flash.

Program 4 – Red Color Ramp Up and Flash
Red color brightens from 0%‐100% and shuts down, then flashes three times.

Program 5 – Green Color Ramp Up and Flash
Green color brightens from 0%‐100% and shuts down, then flashes three times.

Program 6 – Blue Color Ramp Up and Flash
Blue color brightens from 0%‐100% and shuts down, then flashes three times.

Program 7 – Color Change and Flash
Several colors fade into each other and then flash randomly.

Program 8 – Fade In/Fade Out
Several colors fade into each other.

Program 9 – Strobe White
White color flashes.

NOTE:
Your wireless remote has aleady been paired for your light set on Zone 1.

In the event that your light set becomes unpaired or to link additional lights to the remote, follow the steps below.

Linking new lights to the remote control:

1. Choose which zone you want to assign the lights (1 to 4)
2. Switch off the main power supply of the lights in the selected zone with the main switch or pull the plug from the socket.
3. Now switch on the lights again and within 3 seconds shortly press one of the ‘Zone ON’ buttons, one time, on the remote control.
4. When the link operation is successful, the lights will slowly blink on and off 3 times.

Maintenance & Winter Storage

1. Maintenance
2. Disconnect ALL power from the fountain and lights before attempting any maintenance.
3. Periodically clean light set lens with a non-abrasive brush and cleaner. We recommend Airmax Fountain & Aeration Cleaner (#530298)
4. Winter Removal & Storage
5. Remove the fountain and lights from the pond before ice begins to form.
6. This is the perfect time to clean or power wash any debris on the unit before storing.
7. It is recommended to disconnect lights from fountain and store in an area above freezing temperatures.
8. Spring Installation Inspection
9. Before re-installing the fountain and lights in the spring, check the condition of the power cord and quick disconnect. Replace any o-rings that may be worn.

Troubleshooting

IF ALL LIGHTS OFF

ISSUE| CORRECTION
GFCI Tripped| Reset GFCI
Power Cord Cut| Repair or replace power cord
Water in fixtures| Contact Airmax or local dealer for repair/replacement
Voltage not high enough for starting| Make sure voltage at receptacle is 120V+-5%
Timer not running| Verify timer is keeping time, replace timer if not
Timer trippers are not set correctly| Set on / off trippers correctly
Photocell defective| Replace photocell
IF ONE OR MORE (NOT ALL) LIGHTS OFF
ISSUE| CORRECTION
Water in fixtures| Contact Airmax or local dealer for repair/replacement
LED bulb driver failed
LED Bulb failed
IF LIGHTS DIM
ISSUE| CORRECTION
Voltage not high enough for starting| Make sure voltage at receptacle is 120V+-5%
Lens might be dirty| Clean with a non-abrasive brush or cleaner
IF ONE OR MORE (NOT ALL) LIGHTS DIM
ISSUE| CORRECTION
Water in fixtures| Contact Airmax or local dealer for repair/replacement
Photocell defective| Replace photocell
LED bulb driver failed| Contact Airmax or local dealer for repair/replacement
IF ONE OR MORE (NOT ALL) LIGHTS DIM
ISSUE| CORRECTION
Water in fixtures| Contact Airmax or local dealer for repair/replacement
Photocell defective| Replace photocell
LED bulb driver failed| Contact Airmax or local dealer for repair/replacement
IF LIGHTS FLICKER
ISSUE| CORRECTION
Water in fixtures| Contact Airmax or local dealer for repair/replacement
Voltage not high enough for starting| Make sure voltage at receptacle is 120V+-5%
LED bulb driver failed| Contact Airmax or local dealer for repair/replacement
IF LIGHTS TURN ON AND OFF INTERMITTENTLY
ISSUE| CORRECTION
Water in fixtures| Contact Airmax or local dealer for repair/replacement
Photocell defective| Replace photocell
LED bulb driver failed| Contact Airmax or local dealer for repair/replacement

Replacement Parts

LED Light Replacement Parts

1. #651307 – Mounting Clamp

2. #651325 – Tension Screw, ¼ – 20 x 1 ¼”

3. #651722 – Bolt, ¼ – 20 x 1 ¼”

4. #651723 – Washer, ¼”

5. #651308 – Band Clamp

6. Power Cord Options
   #652646 – 100 feet, 16/3
   #652647 – 150 feet, 16/3
   #652648 – 200 feet, 16/3
   #652649 – 250 feet, 16/3
   #652667 – 300 feet, 16/3
   #652668 – 350 feet, 16/3
   #652669 – 400 feet, 16/3

7. #651060 – Strain Relief (16 gauge)

8. #651357 – Power Cord End Cap, Female

9. #651163 – Female End Cap, O-Ring

Airmax, Inc. Airmax LED Light Sets Limited Warranty

Airmax, Inc. warrants to the original purchaser (the end user) of any Airmax LED Light Sets manufactured by Airmax, Inc. that any component which proves to be defective in materials or workmanship, as determined by the factory within 3 years from the original purchased date, will be repaired or replaced at no charge with a new or remanufactured part, and returned freight prepaid. The end user shall assume all the responsibility and expense for removal, packaging, and freight to ship to Airmax, Inc. to determine the warranty claim and for all reinstallation expenses.

The warranty is void in cases where damage results from: improper installation, improper electrical connection, improper voltage, alteration, lightning, careless handling, misuse, abuse, disassembly of unit or failure to follow maintenance or operating instructions. Modification or repair by an unauthorized repair facility will void the warranty.

In no case will Airmax, Inc. or its dealers accept responsibility for any costs incurred by the user during installation, removal, inspection, evaluation, repair, parts replacement, or for return freight. Nor will any liability be accepted for loss of use, loss of profits, loss of goodwill, for consequential damage, or for personal injuries to the purchaser or any person.

In the event of problems believed to be covered under warranty, it will be necessary to notify the dealer who will try to help resolve the problem and who may contact the factory for additional assistance. If it is concluded that there may be a defect which may be covered under warranty, it will be necessary to get a Return Material Authorization (RMA) from the dealer before shipment. Freight collect shipments will not be accepted by the factory on warranties or repairs.

The product or part(s) must be returned freight prepaid, to the factory, as directed, and in its original packaging or in a container which will prevent damage. Parts returned under warranty and damaged during shipping will not be covered under warranty for the shipping damage. If the factory evaluation of the returned goods concludes that the failure is due to defects in materials or workmanship, the part or parts in question will be replaced under warranty with new parts, remanufactured parts, or will be repaired; at the factory’s option. The warranty period for all parts supplied under warranty will terminate at the end of the original product’s warranty. All warranty shipments from the factory will be shipped freight prepaid.

Warranty registration is HIGHLY recommended.

No implied warranties of any kind are made by Airmax, Inc. for its products, and no other warranties, whether expressed or implied, including implied warranties of merchantability and fitness for a particular purpose, shall apply. Should an Airmax, Inc. product prove to be defective in materials or workmanship, the retail purchaser’s sole remedy shall be repair or replacement of the product as expressly provided above.

The manufacturer’s warranty will begin from the dealer’s original purchase date if the product is not registered. To register a product, you are required to fill out the warranty registration form at airmaxeco.com/warranty. Warranty registration must be submitted directly to Airmax within 30 days of the end-users purchase date.

Support

Airmax Inc.
Safe, Simple Solutions™

P.O. Box 38
Romeo, MI 48065

(866) 4-AIRMAX
Visit: airmaxeco.com

References

• Airmax

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>