axis TPMS403 DIY Tyre Pressure Monitoring Instruction Manual
- June 7, 2024
- AXIS
Table of Contents
axis TPMS403 DIY Tyre Pressure Monitoring Instruction Manual
MONITOR
– Reliable & Easy to Fit DIY Installation
– 12 Volt DC Cig Lead Power Socket
– Can Connect up to 4 Sensors
– Widescreen LCD Display: 35mm Diagonal (30W x 15H mm)
– Adjustable Display Angle: >90°
– Pressure Parameter Setup
– Low Pressure / Temperature Alarm
– Settings & Menu Buttons
– Sensor Learning
– Sensor Position
– Sensor Battery Alert
– PSI or Bar Select
– Operating Frequency: 433.92 MHZ
– Operating Temperature -40°c to 85°c
SENSORS
– External Mounting
– 23mm Sensor Caps
– Low Profile
– Water Resistant
– Screws onto Valve Stem for quick & easy installation
– Tyre Pressure Range: 0 to 50 PSI
– Pressure Accuracy 1.45 PSI
– Transmission Frequency: 433.92 MHZ
– Working Temperature -20c to 70c
– Operating Voltage: 3.0V (3.0 – 3.6V)
– Security: Hex Locking Nuts & Tamper Basket
– Replaceable CR1632 Button Battery
INCLUDED
– Installation Accessories
INSTRUCTION MANUAL
About the product
- The TPMS (tyre pressure monitoring system) is a wireless RF sensing device designed to measure and display the tyre pressure and temperature.
- The TPMS function can help you to avoid tyre accidents due to tyre failure, to reduce fuel consumption and to extend the tyre life.
- Once installed in your vehicle, the TPMS will warn you of any abnormal tyre condition immediately with an audible and visual alert.
- External valve-cap sensor battery can be changed. Maximum battery life is 2 years.
Packing list
Technical specification
Installation
Before installation, please plug-in cigarette plug display & turn on car
accessories. Then, install sensors as per their correct position. The display
will show tyre pressure and temperature.
If you install the sensors before the display power is on; the display will
show “00” or”-“, this is normal, please follow step 4 to test.
- Please plug-in cigarette plug display, start the car engine.
- External sensor installation position as below.
- External sensor installation
Important Notice – Please read:
The four sensors are programmed as a system during production. This system is
ready to use with the default settings- high pressure 43 psi, low pressure 29
psi, high temperature 68C. Users do not need to carry out any programming
procedures or setting adjustments. Specifications may change without notice.
4. The driving test
Display
- Left arrow button
- Select button
- Right arrow button
- Alarm symbol
- Tyre pressure
- Pressure unit
- Tyre indicator
- Temperature unit
- Power supply positive pole
- Power supply negative pole
Function and alarm settings
1. High pressure warning
When the tyre pressure exceeds default high value, (e.g. 43 Psi) the corresponding tyre symbol will flash on the display with an audible warning.
2. Low pressure warning
When tyre pressure bellows default low value, (e.g. 29 Psi) the corresponding tyre symbol will flash on the display with an audible warning.
3. Fast tyre leakage warning
When tyre pressure drops suddenly, the corresponding tyre symbol will flash on the display with an audible warning.
4. High temper1!ture warning
When tyre temperature exceeds the default high temperature setting, (e.g. 68C) the corresponding tyre symbol will flash on the display with an audible warning.
5. Low battery warning
When the sensor battery is low, the corresponding tyre symbol will show “Lo” on the display. Please change the battery.
6. No sensor signal
If the sensor is damaged, the a battery runs out or a signal is not received by the display for 40 minutes; the corresponding tyre symbol will show “Er” on the display.
Note: Press any button to cancel the audible warning
Battery replacement chart
TPMS System set up
Pairing Sensor
A replacement sensor will need to be paired to the monitor before use.
- Press and hold the select button for 3 seconds to enter the menu. will flash.
- Press the left button once to enter pairing mode.
- Press the right button repeatedly until the desired sensor position is selected.
- Insert a CR1632 battery into the sensor. The display will beep.
- Remove the battery to complete the pairing procedure.
- Press the select button twice to exit the menu.
- Insert the battery and screw the cover back on.
- The sensor is now ready to be used.
Important Notice
Troubleshooting
Q: Can the sensor easily be stolen or fall off while driving?
A: The sensor needs a special tools to remove it.
Q: Is the tyre pressure detection accurate?
A: This product uses German Infineon IC, with error of +1 psi/-1 psi accuracy.
Q: Do I need to have the tyre balanced after the sensors are installed?
A: The sensors weighs only 10 grams, so may not require balancing.
Q : After installation of sensors, why does the display not show Pressure?
A: When installing sensors please keep the monitor on, as the sersors will
send a signal to
the display so it can detected tyre pressure.
Q: Is it possible to adjust the pressure/ temperature alarm value?
A: Yes, you can adjust values. Please refer to the “TPMS System Setup”
section.
Q: Why does the tyres pressure change while driving?
A: When a tyre is cool after being stationary for a period of time, the tyre
pressure will be lower, this is normal. When the tyre temperature increases,
the pressure will also increase.
Q: Why does the sensor leak air?
A: Please check valve, usually the valve mouth edge has some damaged. Replace
with valve.
WARRANTY
Congratulations on your purchase of a quality Mobile Safety System! You’re
joining thousands of satisfied customers who enjoy & experience the benefits
of the products we distribute. In the unlikely event that some technical
difficulty arises with your purchase, be
assured that we are most anxious to see that the problem is quickly rectified
to your satisfaction. Please familiarise yourself with the following simple
conditions of our warranty.
This warranty covers faults through component failure or failure of the
product to operate in accordance with published specifications. Product
failure as a result of unreasonable environmental conditions, accident,
misuse, improper installation, unauthorised repair, vehicle
electrical or wiring faults or neglect etc, will not be covered by this
warranty. Removal and installation costs, if any, would be paid by the owner
as well as any freight or postage costs of transporting the product to
AudioXtra. AudioXtra shall not be liable or responsible for any loss of use of
this product or any form of consequential loss.
CONSUMER WARRANTY
This product is warranted by AudioXtra International Pty Ltd to be free from defects in materials and workmanship under NORMAL USE for a period of TWELVE MONTHS from the date of purchase.
WITHIN 30 DAYS OF PURCHASE DATE: Please return the unit for replacement
to our National Service Centre or the Retailer from where you made the
purchase. All accessories must be included. Proof of purchase date must
accompany the products.
AFTER30 DAYS OF PURCHASE DATE: Warranty repair and service is carried out
by our National Service Centre. Repair and service will be carried out at no
cost to the owner if proof of ownership and the date of purchase can be
verified to the satisfaction of the authorised centre concerned with this
repair. This proof should take the form of either:
- The warranty card accompanying this product, stamped and dated by the dealer.
- A Tax Invoice or Receipt showing full details of original vendor, purchaser, model number and serial number.
COMMERCIAL WARRANTY: A product used in or associated with a commercial
application will carry a limited SIX MONTH warranty. An abnormal commercial
application is one where usage, dust, vibration, heat/cold and other
environmental conditions exist at an extreme level.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
National Service Centre:
10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148Australia
Telephone: (02) 8841 9000 Fax: (02) 9636 1204 email:
services@audioxtra.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>