Malide MLD-B02 Voice Broadcaster User Manual

Malide MLD-B02 Voice Broadcaster User Manual

Product Introduction

Malide BLE Tire Pressure Monitoring System (hereinafter referred to as Malide TPMS) can monitor the pressure and temperature of car’s tire,and the value can be correctly displayed through App. If the abnormalities occurs on the tire’s pressure and temperature, the App will send the alarm to you through the voice and warning icon.

Precautions

1. Users should match the sensor and APP before driving, please do not match during the driving to avoid the unnecessary property losses and personal injuries, otherwise, you will undertake the all the responsibilities and risks.
2. This product performs the wireless signal transmission. If the environment of wireless communication is special, the installation method is incorrect or there are other special reasons, the wireless signal may be interfered and the signal will be reduced or lost.
3. If the temperature and pressure of tire display abnormally, please drive your car to the repair shop where it is closer to you for inspection and repair to avoid the accident.
4. When indicate that the battery is too low, please replace the battery or the sensor in time to avoid the abnormal operation of tire pressure detection system due to low battery.
5. If the sensor is not used properly due to the use of a gas-filled puncture sealant or other external human factors, or the accident occurs, the company will not bear any responsibility.

List of Accessories

Instruction for Installation on the Car

When the product leaves the factory, the sensors and ID codes of four tires have been configured (each sensor has an independent ID code), just need to install the sensor to the corresponding positions of tires, and use it. You need to match the App with sensors first when you want to watch the data (See the “Matching Procedures for Sensors” for the matching method).

Procedures of Installation

Voice Broadcaster Introduction

Function Description:

1. USB Plug: Plug the USB plug into the USB port and support 5V DV for the voice broadcaster
2. Button: Used when matching the App, see the “Matching Procedures for Sensors “for the matching method
3. Horn: Broadcast the voice of tire condition
4. Indicator light: When the tire is abnormal, it will flash red light; When the tires are normal, the blue light will be on

Voice Description

1. The voice broadcaster will broadcast “Have a nice trip “just after powering up
2. The voice broadcaster will broadcast “Have a nice trip “when press the button in a short time
3. When the tire is abnormal, it will broadcast the corresponding warning voice. Such as: “Left front tire pressure is too low”” Left rear tire pressure is too high”” Right rear tire temperature is too high” “Right front tire leakage”” Left front tire battery is too low”

Matching Procedures for Sensors

1. Click the symbol in the upper right corner of the main interface of Figure A to enter the system setting interface, as shown in Figure B.
2. Click “Binding new device” to enter the interface shown in Figure C.
3. Manual matching: Click the tire selection box to be matched, input the ID engraved on the sensor and click to complete the matching.
4. Automatic matching: Click the tire selection box to be matched, enter the 120 second search countdown, click “Confirm” after the ID appears, and then the matching is completed. (Note: When using automatic matching, you need to ensure that the sensor is awaken, otherwise the App will not be able to search for ID code)
5. QR matching: Click the tire selection box to enter the scanning code state, scan the QR code on the sensor shell. As soon as the scanning is completed the matching will be completed.

Binding of Voice Broadcaster

1. After binding the ID codes of all the tires, click the upper right corner of the main interface to set the symbol to enter the interface A.
2. After entering the interface of Figure B, click on “Supporting Device Binding”.
3. After entering the interface of Figure C, click on “Searching for Device “to find the voice player.
4. Shortly press the button to turn on the voice receiver, then press and hold the voice player button on the top of player for 5 seconds until the red and blue lights flash alternately. Then the voice broadcaster enters the matching mode.
5. When the “MLD_R03 key in Figure D appears, click this button to bind.
6. When the “Binding Successful” voice is heard and the prompt box in Figure E appears, the voice broadcaster is bound, and finally click “I Know” to exit the prompt box.

Introduction for more APP functions

1. In the setting interface of system, click the vehicle setting to enter the setting interface of vehicle as shown in Figure A, you can set the picture, name and type of vehicle as well as license numbers.
2. In the setting interface of system, click “System Parameter Setting” to enter the setting interface of system parameter as shown in Figure B, you can either define the temperature and pressure range of the front and tires according to the actual situation, or can replace the display unit or restore the default settings.
3.  In the setting interface of system, click “Setting of Tire Adjustment” to enter the setting interface of tire adjustment as shown in Figure C, you can change the display frame according to the actual sensor position.(You can click on the instruction symbol in the upper right corner to learn the transposition operation)
4.  Click “Help” in the setting interface of system to enter the help interface as shown in Figure D. Here you can view the installation instruction of equipment and the use instruction of App.

Specifications

Common Problems And Solutions

1.  After the sensor is just matched or the App is opened, there is no data display on the main interface. The sensor will only send data in the following situation: Within 20 minutes after the battery is installed; The driving speed exceeds 20 yards; The parking time is within 10 minutes; The tire pressure changes instantaneously more than 30 The tire rotates for more than 20 seconds. When the other time is in the sleeping state, the data will not be sent in sleeping state, so the receiver will not receive the signal.
2. No voice broadcast from the App. Check if the voice alert is on in the setting interface of system; check if the phone is muted or the volume is low.
3. No sound in the voice broadcaster Confirm that the voice broadcaster has completed the binding; the voice broadcaster will not broadcast if there is no abnormality.

Warranty

Thank you very much for supporting our company. This product will have one year warranty from the date of purchase. During the warranty period, if the product fails to function properly due to quality problems under normal use, the company will be responsible for the repair or replacement of product. Products that are repaired or replaced must meet the following conditions:

• The cause of product quality problems is defective products from the factory;
• The product is in accordance with normal usage methods;
• The product has not been improperly dismantled;
• If the product need to be repaired or replaced, they need to be sent to the merchant and explained the reasons of damage and purchase date.

FCC Statement
-This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-· Reorient or relocate the receiving antenna.
-· Increase the separation between the equipment and receiver.
-· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-· Consult the dealer or an experienced radio/TV technician for help.
-Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be use d in portable exposure condition without restriction.

https://itunes.apple.com/cn/app/malide- tpms/id1460105737?l=en&mt=8

Manufacturer Shenzhen Malide Technology Co. Ltd.
Address: Building A, No. 26, Xin’e Industrial Zone, Egongling Community, Pinghu Street, Longgang District, Shenzhen, China
(Company Website) http://malide.com.cn/ (Email) Malide@malide- sz.com

References

• 深圳市马力德科技有限公司-深圳市马力德科技有限公司

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>