4-Axis Aerocraft Aerial Photography Drone Instruction Manual

4-Axis Aerocraft Aerial Photography Drone

4-AXIS ABROCRAFT INSTRUCTION MANUAL

1. This 4-axis aero craft is suitable for indoor/outdoor flying, but make sure the outdoor wind force is not more than grade 4.
2. It adopts 2.4G frequency band; with long controlled distance; allow some helicopters to fly in the same area without any interference. Besides, players can control it to move forward/backward, tum left/right, left/right sideways fly.
3. Please read this manual carefully before using and keep it properly for future reference.

The illustration of the remote control function

1. When the drone flying, press the One Key Start the drone will land, and you can control it land to one place.
2. emergency stop: When the aircraft collides during the flight and cannot be controlled, the emergency stop button can be pressed the One Key Landing button the drone will land slowly, at this point you can use the right joystick to control it to fly to a certain point and the propeller will stop spinning.
3. “Headless” Mode: When pressing the button of “headless mode”, you will hear the sounds “DI” “DI”, then start the headless mode.(At this model, the flying direction is still controlled by the controller .) No matter where the positive direction is, it is according to the operation of the controller. It is very simple and convenient. When you press the key of Headless model, after you hear the sound” DI”, out of the headless model.
4. “Auto return home” mode: in the controllable grange, no matter where you are, after you press this button, you will hear “DI”, then the drone will return to
   the back of the matching signal position. when you pull the stick of the controller or press the button again, out of this model

Unfold the aircraft

When you receive the aircraft. the state of being acquiescent is the folding state, at this time unfold the aircraft arms respectively rotate to outside about 120 degrees(as shown in Figure 2),when you hear a sound of click, the rotation has been in place.
Pull the propeller up for removal and press it down for installation figure 3

Installation of mobile phone clips (W1F1 only)

Remove the small accessories on the back of the remote control (figure 1)
Put the mobile phone clip on the back of the remote.(figure 2)
put the mobile phone into the clip of the remote control (figure 3)

Battery installation

1. Loosen screw and remove the battery compartment door.
2.  install 3 1.5V AAA batteries (not in included) in the battery compartment as shown, make sure to follow the correct positive”+ “and negative”-“polar pities with the corresponding marking inside the battery compartment.
3. R-e install the battery compartment door and tighten the hold down screw
   

Aircraft battery change

Will craft of lithium battery from the battery holder by graphic method and disconnect the power plug, insert the plug of the charger USB computer USB jack, after connect the charger plug and lithium battery plug, When charging, LED lights, at the end of the USB charging LED lights inside, charging time is about 45 minutes.

Accessories package

This product contains fittings bag:

1. blade guard
2. fan blade A2., B2
3. the USB connection
4. with 1pc manual screwdriver

HOW TO CONTROL

WARNING Push the throttle level slowly; please press the trimming buttons when the aero craft hovers or leans to different directions in the

ATTENTION; Push the throttle level slowly; please press the trimming buttons when the aero craft hovers or leans to different directions in the

3D FLIP FLYING Players can control it to perform some breathtaking operations when mastering the basics. First, fly it to the height of 3m.Second,click the flip key and push the right rudder to the end(in one direction),and push it: the aero craft turns over.

PROBLEMS AND SOLUTIONS

PRECAUTIONS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. For the drone, it should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>