Monster 190725-00 RGBW RF 2.4GHz Remote User Manual

June 5, 2024
Monster

LIVE IN COLOR

INSTALL LED STRIPS

Peel 3M™ adhesive mounting and press the flexible LED strip into place.

For 6.5-ft LED Strips:
Plug the LED strip into the 5V USB controller cable (3.8ft) and then the cable into any USB port (TV or PC) or USB power supply (not included).

CAUTION: 6.5-foot LED Strips should only be plugged into 5V USB ports.
6.5-foot LED Strips USE ONLY WITH CLASS 2 POWER UNIT
CAUTION: To reduce the risk of fire, do not install closer than 0.5 inches to cabinet wall or in a compartment smaller than 20 inches by 40 inches by 12 inches.
The LED Strip should be installed on smooth surface, e.g. metal, plastic, wood, or glass.

INSTALL LED LIGHT BULBS

USING YOUR REMOTE

Battery Warning Statement
Do not mix old and new batteries and Do not mix alkaline, standard (carbon- zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.
AAA BATTERIES REQUIRED (NOT INCLUDED)

COLOR RING
Choose the color of your lights.

BRIGHTNESS
Dim from 10% – 100%.

PRESET LIGHT PROGRAMS
Eight different auto programs for parties, lounging, and special occasions.

SPEED
Adjust program speeds faster for parties and slower for an elegant change of atmosphere.

PAIRING

By default, all Monster IlluminEssence LED strips and LEDlight bulbs will be paired out of the box with the included remote control.

TO PAIR
To pair LED strips or LED light bulbs to another remote, simply unplug and replug back in the LED strip or lamp to power and WITHIN FIVE SECONDS of plugging back into power, press and hold the “Speed+” until the lights blink three times.

TO UNPAIR

Repeat above but instead of “Speed+” press “Speed-”.

EXPAND

EXPAND LIGHTS AND ROOMS
You can pair up to four remotes with up to 30 Monster IlluminEssence LED strips or LED light bulbs.
You can have multiple remotes control the same set of lights.

You can also have different sets of lights paired to different remotes to control rooms independently.

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Lighted lamp is HOT!

WARNING ­ To reduce the risk of FIRE OR INJURY
CAUTION ­ Use indoors only.
CAUTION ­ Risk of Electric Shock
CAUTION  Hot surface. Keep away from curtains and other combustible materials.

Turn off power and allow to cool before replacing lamp.
Do not touch hot lens, guard, or enclosure Keep lamp away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
Do not operate the luminaire with a missing or damaged shield.
Do not use if there is any damage to the light or cord insulation. Inspect periodically.
THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.

SAVE THESE INSTRUCTIONS

122048-00   INCLUDES: 122047-00   INCLUDES:
1 x RF Remote Control 1 x RF Remote Control
1 x LED Lihgt Bulb 1 x LED Strip

Federal Communication Commission
Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

The Responsible (located within the United States) party information:
Company Name: Monster, Inc.
Address: 280 Old County Rd # 435
Brisbane, CA 94005-1301, USA
Telephone Number: 415-840-2000
Email: ProductCompliance@monstercable.com

The name and model number of the product:

Model Number Model Name
190712-00 6.56FT 5V RGB Strip & 5V RF Strip Controller
190714-00 7W RGB Bulb
190725-00 RGBW RF 2.4GHz Remote

GET INSPIRED

Subscribe to our Pinterest boards to learn all the cool things you can do with Monster IlluminEssence.

For Ideas and Inspiration:
www.pinterest.com/monsterilluminessence

GET HELP

For Instructional Videos:
www.youtube.com/monsterilluminessence

FOR TECHNICAL SUPPORT GO TO:
www.monsterstore.com/pages/contact-us
OR CALL: 1 877-800-8989
rm 880186-00

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals