SUPERATV Can-Am Defender MAX Full Rear Door Installation Guide
- June 7, 2024
- SUPERATV
Table of Contents
SUPERATV Can-Am Defender MAX Full Rear Door/Full Door Installation
Instructions
Full Rear Doors: for Can-Am Defender
Kit Contents
Removal
Keep all components removed from machine.
- Repeat for opposite side.
Driver Door Installation
Do not tighten hardware completely unless noted.
- Install Foam to Driver Hinge Mount (E) as shown.
- Install Driver Hinge Mount (E) to Frame with stock hardware. Tighten hardware.
- Install Driver Hinge Assembly (G) to Driver Hinge Mount (E) with hardware shown.
- Install Clamps (C) to Driver Hinge Mount (E) with hardware shown. Tighten hardware.
- Install Acorn Nuts onto previously installed hardware.
- Install Striker (B) with hardware shown.
- Install Driver Door (A) onto Driver Hinge Assembly (G).
- Close Door, engage Latch / Striker Pin, and align Door to machine.
- Tighten all hardware completely.
- Open Driver Door (A) and install Gas Strut (H) to Driver Door (A) and Driver Hinge Mount (E).
- Secure with hardware shown. Tighten hardware.
- Repeat steps for opposite Door.
Door Cleaning
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse Doors to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Doors with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Doors dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Full Doors: for Can-Am Defender
Kit Contents
KEYS ARE LOCATED UNDER ORANGE TAPE. DO NOT DISCARD.
Door Cleaning
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse Doors to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Doors with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Doors dry
Removal
Keep all components removed from machine.
Driver Door Installation
Do not tighten hardware completely unless noted.
- Install Driver Hinge Mount (E) to Frame with stock hardware. Tighten hardware.
- Install Driver Hinge Assembly (G) to Driver Hinge Mount (E) with hardware shown.
- Install Clamps (K) to Driver Hinge Mount (E) with hardware shown. Tighten hardware.
- Install Acorn Nuts onto previously installed hardware.
- Install provided “U” Joint to Pillar.
- Secure Pillar Bracket (C) to “U” Nut with hardware shown. Tighten hardware.
- Install Clamp (K) to Pillar Bracket (C) and Frame. Tighten hardware.
- Install Striker (B) to Pillar Bracket (C) with hardware shown.
- Install Driver Door (A) onto Driver Hinge Assembly (G).
- Close Door, engage Latch / Striker Pin, and align Door to machine.
- Tighten all hardware completely.
- Open Driver Door (A) and install Gas Strut (H) to Driver Door (A) and Driver Hinge Mount (E).
- Secure with hardware shown. Tighten hardware.
- Remove installed Mounts on Mirrors. Use 8mm wrench. Discard Mount and hardware.
- Install Mirror to Driver Door (A) with hardware shown. Tighten hardware.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>