IPUDA Dual Light Source Monitor Lamp Pro Instruction Manual

IPUDA Dual Light Source Monitor Lamp Pro

Please read this manual carefuly before using the product and keep it properly

Product description

Remote control instructions

1. Main switch key: Short press to turn on-off the front and rear lights, when the front or back lights are on, short press to tum of the lights; When the front and rear lights are tumed on at the same time, short press to tum off the lights; when the front and rear lights are turmed off at the same time, short press to tum on the lights.

2. +Bnghtness up Button: the light tums from dank to bngnt, short press to 5 leves of dimming. long presS to stepless dimming.

3. _Bnghtness Down Buitton: the lignt changes rom bnght to dark, shot press to levels of aimming, long press to stepless dimming.

4. Color Switch for Rear Light Button: Long press to tum on or off and then light, short press to switch color temperature warmm ight-white light-yellow light (cycle in tum).

5. Color Switch for Main Light Button: long press to tum on or off the tront light, short press to switch the color temperature warm
   light-white light-yellow light (cycle in turm).

6. This product has a memory function.

Operation Instructions

1. Take out the lamp holder part, with the main light-emitting area facing down.

2. Take out the bracket, align the power supply port of the lamp head part with the notch at the end of the bracket clip, and buckled it gently.

3. Hang the lamp in the middle of the top of the screen. (Special attention: the fulcrum at the front of the bracket must be close to the screen)

4. Take out the USB power supply line, insert the type-C interface into the power supply part or the lamp head, and plug the other end of the USB into the USB intertace on the rear panel of the chassis or the 5V adapter, and the lamp will automatically light up at this time.

5. Hold the bracket with one hand (to prevent it from falling), and turn the lamp body with the other hand to adjust the angle of the lamp head to complete the installation.

6. Take out the remote control, install the battery, and put it on the desktop to use it normally

Product parameter

• Product net weight: about 335g
• LED Quantity: 84pcs
• Product material: ABS+aluminum alloy
• Lamp body size: ¢20x410mm
• Working temperature: -1oC~+40C
• Input voltage: DC 5V
• Input current: 1000mA
• Color index: Main illumination Ra 2 95
• Power: 5W (main illumination 72×0.2W/LED module+ 12×0.2WILED module)
• Color temperature: warm light 4200K:350Kwhite light 6400K+500K/yellow light 3100K+300K
• Luminous flux: warm light 200LM/whitelight 185LM/yellow light 17OLM

Precautions

1. When the lights are flickering after turning on the lights, please try other USB ports on the computer or replace the adapter.

2. It is recommended to use the USB port on the rear panel of the computer case to power this product.

3. Please use a regular 5V/1A or higher adapter to power this product, Iif you use an adapter to power, please use a regular 5V/1A or higher adapter to power the product.

4. Please use the original power cord, do not use USB extension cords or splitters, otherwise, it may cause the lamp to work
   abnormally.

5. If you use more than 5V adapter to supply power to this product, it may cause damage to the product and bring safety hazards.

6. Do not use in unstable scenes to avoid damage to the lamp due to dumping.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCCNote :
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>