SUPERATV CF Moto UForce 500 Flip Up Windshield Instruction Manual

SUPERATV CF Moto UForce 500 Flip Up Windshield

• Do not discard packaging until the product has been successfully installed.
• SuperATV does not recommend keeping a Windshield installed while transporting on an open-air trailer.
• This item is not returnable if the protective film has been removed.
• Test fit to the cage to confirm fitment before removing the film.

What’s In The Box

Windshield Cleaning

• Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
• Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
• Never use abrasive cleaners, abrasive pads, or gritty cloths.
• Do not use a windshield wiper blade or install a motorized windshield wiper
• Never use razor blades, scrapers, squeegees, brushes, etc.

1. Thoroughly rinse the Windshield to float off dirt and mud.
2. Using a soft cloth, or microfiber cloth, clean the Windshield with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand-washing soap can also be used.
3. To prevent water spots, use a chamois to blot the Windshield dry.

Liability Statement

SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on the machine, contact SuperATV® to verify that they will work together.

Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of the machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect users from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.

By purchasing and installing SuperATV® products, user agrees that should damage occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of the seller to the user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.

SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warranted if the item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation of law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.

The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings, and/or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.

Use hand tools only when assembling

Assembling

• Install Catch and Catch Support to Lower.

• Install Mount – L to Lower with hardware shown.

• Repeat for the opposite end of Lower.

• Install Seal to Lower in the location shown.
  To ease installation, soak the Seal in hot water before cutting or installing to increase flexibility

• Install Handle and Support to Upper as shown.

• Hardware included with Handle.

• Install Clamp to Bracket with hardware shown.

• Repeat for the opposite Bracket.

• Secure Clamps, on Lower, to Cage.

• Install Gasket across Lower in area shown.

• Place the Upper onto the machine.

• Use Straps and Clamps to loosely secure to Cage.

• Align Flip Windshield to machine and tighten hardware.

• Open the Upper and install Struts to Brackets with the hardware is shown; tighten the hardware.

References

• SuperATV.com
• superatv.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>