SHARP FXJ80UW Smart Air Purifier User Manual

SHARP FXJ80UW Smart Air Purifier

Product Information

Specifications:

• Model: FX-J80U
• Trademark: Plasmacluster and Device of a cluster of grapes by Sharp Corporation
• Energy Efficiency: ENERGY STAR certified
• Filters: True HEPA filter, Active Carbon Deodorizing filter
• Filter Efficiency: True HEPA removes 99.97% of dust particles as small as 0.3 microns
• Features: Wi-Fi adapter for connectivity

Product Usage Instructions

Thank you for choosing the SHARP Air Purifier FX-J80U. To ensure optimal performance, please follow these usage instructions:

1. Setup:

Place the air purifier in a central location with enough clearance around it for proper air circulation.

2. Filter Installation:

Insert the True HEPA filter, Active Carbon Deodorizing filter, and back panel (Pre-Filter) as per the instructions provided in the manual.

3. Power On:

Connect the air purifier to a power source and turn it on using the power button.

4. Mode Selection:

Select the desired operating mode (e.g., low, medium, high) based on your air purification needs.

5. Maintenance:

Regularly check the filters for dirt accumulation and replace them as needed to maintain efficiency.

Frequently Asked Questions

• Q: How often should I replace the filters?
  • A: Depending on usage conditions, it is recommended to replace the filters when odors persist or at least every 6-12 months for optimal performance.
• Q: Can I use this air purifier in larger rooms?
  • A: The effectiveness of the air purifier may vary in larger rooms. For best results, place multiple units in different areas or consider a model suitable for larger spaces.

ENGLISH

FX-J80U

AIR PURIFIER OPERATION MANUAL
PURIFICADOR DE AIRE MANUAL DE OPERACIÓN

ESPAÑOL

“Plasmacluster” and “Device of a cluster of grapes” are registered trademarks of Sharp Corporation in Japan, USA and elsewhere.

This product earned the ENERGY STAR label by meeting strict energy efficiency guidelines set by the U.S. EPA. Room air cleaners have demonstrated the potential for improving air quality and providing health benefits. EPA does not endorse manufacturer claims regarding the degree to which a specific product will produce healthier indoor air.
The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model’s CADR for Smoke and the electrical energy it consumes, or CADR/Watt.
Este producto obtuvo el sello de ENERGY STAR al cumplir las estrictas pautas de eficiencia energética establecidas por la EPA de EE. UU. Los purificadores del aire de la habitación han demostrado el potencial para mejorar la calidad del aire y proporcionar beneficios para la salud. La EPA no respalda las afirmaciones del fabricante con respecto al grado en que un producto específico producirá aire interior más saludable.
La eficiencia energética de este modelo con la certificación ENERGY STAR se mide en base a una relación entre el CADR del modelo para el humo de tabaco y la energía eléctrica que consume, o CADR/ vatio.

ENGLISH
Thank you for purchasing this SHARP Air Purifier. Please read this manual carefully before using the product. This manual should be kept in a safe place for future reference.
CONTENTS
FOR CUSTOMER ASSISTANCE……………………………….. EN-2 CONSUMER LIMITED WARRANTY ………………………….. EN-3 IMPORTANT SAFETY INSTRUCTIONS …………………….. EN-4 PART NAMES …………………………………………………………. EN-7 FILTER INSTALLATION …………………………………………… EN-9 OPERATION …………………………………………………………… EN-10 CARE AND MAINTENANCE …………………………………….. EN-13 TROUBLESHOOTING ……………………………………………… EN-16 SPECIFICATIONS……………………………………………………. EN-17 OTHER SETTINGS ………………………………………………….. EN-18 Intellectual property rights for this product……………… EN-22

ENGLISH

Please read before operating your new Air Purifier

The air purifier draws in room air through the air inlet, circulates it through a pre-filter, an Active carbon deodorizing filter and a true HEPA filter inside the main unit, and then discharges it through the air outlet. The
True HEPA filter can remove 99.97% of dust particles as small as 0.3 microns that pass
through the filter and also helps absorb odors. The Active carbon deodorizing filter gradually absorbs odors as they pass
through the filter.

True HEPA Filter Active Carbon Deodorizing Filter Back Panel (Pre-Filter)

Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments
significantly more severe than a normal household, these odors may become noticeable sooner than expected. If these odors persist, replace the filters. (Page 9,14)

NOTE
· The air purifier is designed to remove air-suspended dust and the odors. The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke. The air purifier may not completely remove an odor if the source of the odor is still present.

Declaration of Conformity SHARP AIR PURIFIER FX-J80U This device complies with Part 18 of FCC rules.
Responsible Party: SHARP ELECTRONICS CORPORATION 100 Paragon Drive, Montvale, NJ 07645, U.S.A.

This Wi-Fi adapter complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
· Contains FCC: RX3-B01

EN-1

FOR CUSTOMER ASSISTANCE

REGISTER YOUR PRODUCT

Registering your new product is easy and offers benefits that help you get the most out of your Sharp product including:

Convenience: If you ever need warranty support, your product information is already on file.

Communication: Stay up to date with important notifications and special offers from SHARP.

Support:

Quickly access support content including Owners Manuals, FAQ’s, How-to Videos, and much more.

3 EASY WAYS TO REGISTER TODAY!

SCAN
Use the camera or QR code scanning application on your smart phone

ONLINE
Visit our sites to learn more about your product at sharpusa.com and sbl.sharpusa.com

CALL US

US

800-BE-SHARP

800-237-4277

Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST

Scan this QR Code on your smart phone Visit http://www.sharpusa.com/register Contact a Sharp Advisor on the phone

PRODUCT SUPPORT
If you have questions about the setup or operation of your product, please refer to the corresponding section within this manual.
Additionally, visit www.sharpusa.com/support to access exclusive content about your product including:
FAQ’s and How-To Videos Find or Request Service Downloads including the Installation Guide, Spec Sheet, and Owner’s Manual
CONTACT US
If at any time you have questions or comments concerning your SHARP product, please contact the SHARP Customer Assistance Center. We are available to assist you through multiple contact methods for your convenience:

EMAIL
Available 24/7
US: sharpusa.com
See the Contact Us section on our sites

CHAT ONLINE
Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST
U.S. | www.sharpusa.com/support

CALL US

US

800-BE-SHARP

800-237-4277

Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST

Contact a Sharp Advisor on the phone

EN-2

CONSUMER LIMITED WARRANTY

ENGLISH

CONSUMER LIMITED WARRANTY FOR U.S. USERS SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.

Your Product Model Number & Description: Warranty Period for this Product: Additional Item(s) Excluded From Warranty Coverage: Where to Obtain Service:
What to Do to Obtain Service:

FX-J80U Air Purifier. Be sure to have this information available when you need service for your Product.
One (1) year parts and labor from date of purchase.
Appearance items of the Product, filters, accessories, or any printed materials. Product which has been used for rental and/or commercial purposes. From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, call Sharp Toll Free at 1-800-BE-SHARP. Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and packaged securely.

TO OBTAIN SERVICE, SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE- SHARP, OR VISIT OUR WEBSITE AT www.sharpusa.com SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR AIR PURIFIER EVER REQUIRE WARRANTY SERVICE.

SHARP ELECTRONICS CORPORATION
100 Paragon Drive, Montvale, NJ 07645, U.S.A.
EN-3

IMPORTANT SAFETY INSTRUCTIONS

Read and save these instructions before using this product.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
WARNING
1. Read all instructions before using the product.
2. Use the product only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
4. Never operate the product if the power cord or plug is damaged or the product is malfunctioning or damaged.
5. If the power cord or plug is damaged, it must be replaced by the manufacturer, its service agent or a Sharp authorized Service Center in order to avoid a hazard. Contact the nearest Service Center for any problems, adjustments, or repairs.
6. Do not repair or disassemble the product yourself.
7. Follow the instructions a to h below for the power cord or plug. It may cause short circuit, excessive heat, electric shock or fire. a. Use only AC 120 volt outlet. b. Do not use the product if the power code or plug is damaged or the connection to the wall outlet is loosened.

c. Always turn off the product before unplugging the power plug.
d. Always unplug the product before moving or maintaining it, opening the back panel, changing the filters and whenever the product is not in use.
e. Be sure to pull the power plug and not the power cord.
f. Do not touch the power plug with wet hands when inserting or unplugging from the wall outlet.
g. Periodically remove dust from the power plug.
h. Always observe the following not to damage the power cord. · Do not run cord under carpeting. Do not cover the power cord with throw rugs, runners, or similar coverings. · Do not put heavy things on the power cord or pinch it. · Do not run the power cord under furniture or other appliances. · Run the power cord away from traffic area and where it will not be tripped over.
8. The product has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician or service person. Do not attempt to defeat this safety feature.
9. Do not use this product near gas appliances, fire places, candle fire, incense or sparks from lit cigarettes.
10. Do not operate the product in a room with flammable gas, such as oily residue or chemical fumes.
11. Do not expose the product to rain, or use near water, in a bathroom, laundry area or other damp location.
12. Do not insert fingers or foreign objects into the air inlets or air outlets.
13. Do not look into the air outlets.

EN-4

IMPORTANT SAFETY INSTRUCTIONS 2

ENGLISH

NOTE – Radio or TV Interference
If the product should cause interference to radio or television reception, try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving
antenna. 2. Increase the separation between the
product and radio/TV receiver. 3. Connect the product into an outlet on
a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.
CAUTIONS CONCERNING INSTALLATION
1. Place the product on a level and stable surface with sufficient air circulation. When placed on heavy carpet, the product may vibrate slightly.
2. Avoid a location where the sensors are exposed to direct breeze or draft if the product has sensors. The product may not operate properly.
3. Avoid use in locations where furniture, fabrics, or other items may come in contact with and restrict the air inlets and/or outlets.
4. Avoid locations exposed to direct sunlight. It may cause to change shape or color of the product.
5. Avoid locations where the product is exposed to condensation or drastic changes in temperature. Use under appropriate conditions between 32 – 95 ºF (0 ­ 35 ºC).
6. Avoid use in locations where greasy or oily smoke is generated. (such as in a kitchen, etc.). The main unit surface may crack and the sensors may malfunction as a result.
7. The dust collecting ability of the product is effective even when the product is as close to 1.2 inches (3 cm) from the wall, but the surrounding walls or floor may get dirty. Please place the product at a distance from the wall.

The wall directly behind the air outlets and the floor or rug on which the product placed may become dirty over time. When using the product for an extended period of time at the same location, periodically clean the walls, the floor or the rug.
CAUTIONS CONCERNING FILTER
1. Follow the instructions in this manual for filter installation and maintenance. (Page 9,13,14)
2. Take out the filters from the plastic bag before placing the filter in the main unit.
3. Do not operate the product without the filters properly installed.
4. Do not wash and reuse the True HEPA filter and the Active carbon deodorizing filter. Washing will not improve filter performance and can also cause electric shock or operating malfunctions.
5. Do not operate the product in a rooms where aerosol insecticides are present. It may cause the odor of insecticide may be remained in the product and emitted from the air outlets.
CAUTIONS CONCERNING OPERATION
1. Do not block the air inlets or air outlets. 2. Always operate the product in an
upright position. 3. Always hold the handle of the product
when moving it. 4. Always lift up the product when moving
it on easily damaged flooring, an uneven surface, or carpet.

EN-5

IMPORTANT SAFETY INSTRUCTIONS 3
CAUTIONS CONCERNING MAINTENANCE
1. Follow the instructions in this manual for maintenance. (Page 13 – 15)
2. Clean the exterior with a soft cloth only. 3. Do not use volatile fluids and/or
detergents. The main unit surface may be damaged or cracked with strong corrosive cleansers, benzine, paint thinner, polishing powder or grease. In addition, the sensors may malfunction as a result if the product has sensors. 4. Do not scrub the back panel (pre-filter) hard during its maintenance. 5. When replacing filters or any accessories, use specified parts in this manual.
EN-6

ENGLISH

PART NAMES 1

(FRONT)

1

2

3 6

4

7

5

(BACK)

8

12

9

1 Operation Panel

2 Air Outlet (Front / Back)

3 Air Quality Monitor

4 Front Display

5 Main Unit

6

Handle (2 locations: Left and Right)

7 Front Louver

8 Back Panel (Pre-Filter)

9 Air Inlet

10 Active Carbon Deodorizing Filter

11 True HEPA Filter

Sensor Filter

12

Sensor (Internal) Odor / Sensitive dust /

Temperature / Humidity

13 Unit (Plasmacluster Ion Generating Unit)
14 Unit Holder

15 Unit* Cover

16 Unit* Cleaning Brush

17 Power Cord, Plug

*The Unit refers to Plasmacluster Ion Generating Unit.

16

13 14 15

17 11 10 EN-7

PART NAMES 2
OPERATION PANEL Press either button with ” ” to start.
10 9

8765432

1

FRONT DISPLAY
11

12 13 14 15 16 17 18 19 20 21

22

For details on items marked with ( ), refer to the Wi-Fi Connect Guide. * Press and hold 3 seconds or longer.

1 POWER ON/OFF Button

2 Wi-Fi Button ( )

3 AUTO Button, Indicator Light – white

4

PLASMACLUSTER EXPRESS CLEAN Button, Indicator Light – white

15 Dust Monitor 16 Odor Monitor
Continuously monitors dust or odor in the air and changes color depending on purity.

TURN OFF Orange

Red

Clean

Impure

5

Plasmacluster Ion SPOT Button, Indicator Light – white

Fan Speed Button, Indicator Lights – white
6 (Press 3 sec.*) Plasmacluster Ion ON/OFF Button

7

TIMER Button (Press 3 sec.*) FILTER RESET Button

8

DISPLAY Button (Press 3 sec.*) CHILD-LOCK Button

9 Child-Lock Indicator Light – white

10 Light Sensor

Air Quality Monitor

11

Indicates the air purity of the room in 5 levels with color changes.

Blue

Red

Clean

Impure

12 Wi-Fi Indicator ( )

13 SHARP CLOUD Indicator ( )

PM2.5 Monitor

Indicates the sensitive dust sensor detects microscopic

14

dust.

TURN OFF Orange

Red

Clean

Impure

17 Unit Replacement Indicator

18 Filter Maintenance Indicator

19 ON Timer Indicator

20 OFF Timer Indicator

21 Plasmacluster Ion Indicator

DISPLAY The displayed numbers are approximate values.
· PM2.5 Monitor
PM2.5 10g/m3 to 499g/m3 is displayed.

9g/m3 or less

500g/m3 or more

· Wattage Monitor

Indicates wattage by current operation.

· Humidity Monitor

22

Humidity 20% to 90% is displayed.

20% or less
· Temperature Monitor
Temperature 32oF to 122oF is displayed.

90% or more

31oF or less
· Timer Monitor
Indicates setting time or remaining time of ON/OFF timer.

123oF or more

EN-8

ENGLISH

FILTER INSTALLATION

· To maintain the quality of the filter, it is installed in the main unit and packaged in a plastic bag.
· Be sure to stop operation and unplug the product before filter installation or replacement.

1. Remove the back panel.

4. Install the back panel.
Click 3

Back panel
2. Take out the filters from the plastic bag.
Active Carbon True HEPA Filter Deodorizing Filter
3. Install the filters in the correct order as shown.

2

1

5. Record the date when you start or replace the filters on the back cover of this manual.

True HEPA Filter Filtro true HEPA
Starting date of use Fecha de comienzo de uso

Model Modelo

FZ-J80HFU

. .

. .

. .

. .

. .

. .

Active Carbon Deodorizing Filter

Model

Filtro desodorizante de carbón activo Modelo

FZ-J80DFU

Starting date of use Fecha de comienzo de uso

. . . . . .

. . . . . .

NOTE · Do not operate the product without the filters.

Active Carbon Deodorizing Filter

True HEPA Filter

EN-9

OPERATION 1

START/STOP
START

STOP

PLASMACLUSTER ION SPOT MODE

NOTE · Unless the power plug has been unplugged, the
operation will Auto Resume in the previous mode it was operating in. Example: if the power is lost during operation, the operation will resume to previous operation mode and settings if power is restored.
AUTO MODE
The fan speed is automatically controlled depending on the 3 detections. (Dust / Odor / Light)

· The product emits high density Plasmacluster ions only in the forward direction.
· The product produces stronger air for 8 hours. When the operation finishes, the product will return to its prior operation mode.
· The Plasmacluster Ion Mode cannot be turned “OFF”.
FAN SPEED BUTTON

NOTE · When light control is set to “Auto”, front display,
air quality monitor will automatically switch ON or dims based on room brightness. (Page 12)
PLASMACLUSTER EXPRESS CLEAN MODE
The air purifier releases Plasmacluster ions at max air flow for 10 minutes. After that, it operates for 50 minutes on high fan speed.

· When the operation finishes after 60 minutes, the product will return to the prior operation mode. It is able to change to other modes during this operation.
· The Plasmacluster ion cannot be turned “OFF”.

POLLEN SLEEP LOW MED MAX
SLEEP:
The product will operate quietly, and the fan speed will automatically switch depending on the amount of impurities in the air and room brightness. The front display and air quality monitor automatically switches dims or turns OFF based on room brightness. Room is bright: light is dimmed Room is dark: light is OFF
POLLEN:
The dust sensor is automatically increased and quickly detects impurities such as dust and pollen and cleans the air powerfully.

EN-10

ENGLISH

OPERATION 2

ON TIMER
Set the ON TIMER when you would like to schedule the air purifier to turn on after a certain number of hours.

(with the product OFF)

Front Display

· Every time you press the TIMER button, it will change the auto start time in the following sequence:

……

1hour 2hour 3hour

12hour Cancellation

NOTE
· If you have already set the timer using the App, you cannot set the timer using the product.

OFF TIMER
Set the OFF TIMER when you would like to schedule the air purifier to turn off after a certain number of hours.

(with the product ON)

Front Display

· Every time you press the TIMER button, it will change the auto shutdown time in the following sequence:

……

1hour 2hour 3hour

12hour Cancellation

NOTE
· If you have already set the timer using the App, you cannot set the timer using the product.

SELECTING DISPLAY
(with the product ON)

PM2.5 level
Wattage
Humidity
Temperature

CHILD LOCK

The operation panel will be locked.

ON

CANCELLATION

Press for 3 sec.

Press for 3 sec.

NOTE
· It is possible to turn Wi-Fi off while in Child Lock Mode.

PLASMACLUSTER ION ON/OFF

When the Plasmacluster function is ON, the Plasmacluster ion indicator light is on. (Page 8)

(with the product ON)
ON

OFF

EN-11

Press for 3 sec.

Press for 3 sec.

OPERATION 3

HOW TO CHANGE VARIOUS SETTINGS

You can change the functions listed in the table below.

1. Turn the product OFF.

3. Select “Function Number”.

GO BACK

GO FORWARD

or

2. Select

Set

See below table for functions.

Press for 3 sec.

· You can select F or A.

Product setting

Wi-Fi setting

• For details on selecting A, refer to Page 19 – 21.

4. Select “Setting Number”.

GO BACK

GO FORWARD

or

Set

See below table for settings.

Set

5. Finish the setting.

Turn off

Function ( )

Setting ( )
Turn off *

Dim

Light control You can select the brightness of the front display and air quality monitor.
Auto resume This model has Auto Resume function, where the operation resumes at the previous operation mode and settings if the power is restored.
Adjusting sensor sensitivity (F3-F5) For details, refer to Page 16. Light sensor

Auto (default) Light automatically switches based on room brightness.

Room brightness
Bright Dark

Front Display and Air Quality Monitor

ALL MODE (Except SLEEP)

SLEEP MODE

ON

Dim

Dim

Turn off

Cancellation

ON (default)

Low

Sensitive dust sensor

Standard (default)

Odor sensor

High

• When set to “Turn off”, the “Dim” light illuminates for 8 seconds after operation starts and then the light turns off.

EN-12

ENGLISH

CARE AND MAINTENANCE 1

· To maintain optimum performance of this air purifier, please clean the product including the filter periodically.
· Be sure to stop operation and unplug the product before any maintenance or replacing accessories.

MAIN UNIT / BACK PANEL

FILTER MAINTENANCE INDICATOR

When the filter maintenance indicator light turns on.

The filter maintenance indicator light will turn on when it is time to maintain the back panel (pre-filter) . This indicator light will turn on after approximately 720 hours operating. (30 days × 24 hours = 720 hours)
After maintenance, connect the power plug to the wall outlet and press POWER ON/OFF button, then TIMER button for 3 seconds.

RESET

Press for 3 sec.
MAINTENANCE
Wipe with a dry, soft cloth
Back panel (Pre-filter)
Remove the dust gently with a cleaning tool such as a vacuum cleaner.

Turn off

How to clean hard to remove dirt.
Back panel 1. Add a small amount of neutral detergent to
water and soak for about 10 minutes.
NOTE Do not apply excessive pressure when scrubbing the back panel. 2. Rinse off the neutral detergent with clean water. 3. Completely dry the filter in a wellventilated area.

Sensor filter 1. Remove the back panel.

Sensor filter

2. Remove the sensor filter.

3. If the sensor filter is very dirty, wash it

with water and dry it thoroughly.

EN-13

CARE AND MAINTENANCE

TRUE HEPA FILTER / ACTIVE CARBON DEODORIZING FILTER
REPLACEMENT AND MAINTENANCE CYCLE

Filter Name

Maintenance Cycle

Max Service Life Replacement Filter Model

True HEPA Filter
Active Carbon Deodorizing Filter

Whenever dust accumulates, when odor emanates from the air outlet, or once a month.

2 years*1, 2

FZ-J80HFU FZ-J80DFU

¹ According to Japan Electric Manufacture’s Association JEM 1467, the Max service life is based on the equivalent condition of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with that of new filter. It is recommended to replace the filter more frequently under more severe conditions.
² Designated App notifies when filters or Plasmacluster ion generating unit should be replaced according to usage.

MAINTENANCE

Remove the dust on the filters.

TRUE HEPA FILTER
Tag

Maintain only the tagged surface. Do not clean up the opposite surface. The filter is fragile, so be careful not to apply too much pressure.

NOTE Do not wash the filters. Do not expose to sunlight. (Otherwise these filters may lose efficacy.)
ACTIVE CARBON DEODORIZING FILTER
Both surfaces can be maintained. The filter is fragile, so be careful not to apply too much pressure.

Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. Replace the filter in those cases or if dust is unable to be removed after maintenance.

REPLACEMENT
See page 9 for directions on how to install the filter when replacing.
· Please consult your dealer for purchase of replacement filter.
· Use only filter designed for this product.
Record the date when you replace the filters on the back cover of this manual.
Scan the QR code for product information and accessories.

FZ-J80HFU: 1 unit

FZ-J80DFU: 1 unit

Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations.

EN-14

CARE AND MAINTENANCE 3

PLASMACLUSTER ION GENERATING UNIT (electrode section)

MAINTENANCE

1. Remove the unit cover, and pull out the unit holder.

2. Remove dusts from the electrode section.
Unit cleaning brush

3. Insert the unit holder in the main unit, and install the unit cover.

ENGLISH

Before cleaning

After cleaning

Electrode Around the base
NOTE · Do not clean with anything other than the unit cleaning brush. Doing so could lead to failures in the unit. · A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance. · Do not touch the electrode directly. Doing so could lead to pain/itching. · Do not transform the electrode section. Doing so can damage it. · Do not touch the connection terminals. Doing so can damage them.

UNIT REPLACEMENT INDICATOR
When the total operation time exceeds 17,500 hours, the unit replacement indicator will flash to indicate that the Plasmacluster ion generating unit needs replacement.
Operating time 17,500 hours
Replace the Plasmacluster ion generating unit
Flash slowly
19,000 hours Stop the emission of the Plasmacluster ions.
Flash quickly * The replacement time is not related to the selected operation mode.

REPLACEMENT

Consult your dealer when purchasing a replacement Plasmacluster ion generating unit. Model: IZ-C90MU

Remove the claw of unit holder ( 1 ),

and remove the Plasmacluster ion

generating unit ( 2 ).

Disposal of Plasmacluster Ion Generating Unit
Dispose of used Plasmacluster ion generating unit according to local laws and regulations.
EN-15

TROUBLESHOOTING

Before calling for service, please review the list below, since the problem may not be the product malfunction.

Odor and smoke persists.
· Check the filters. If they appear to be extremely dirty, clean or replace them.
Air discharged from the product has an odor.
· Check to see if the filters are extremely dirty. Clean or replace the filters.
The product does not operate when cigarette smoke is in the air.
· Make sure the product is installed in a location in which the sensors can detect cigarette smoke.
· Check to see if the sensitive dust sensor openings are blocked or clogged. If they are blocked or clogged, clean the sensor filter or the back panel.
Smell from a new filter.
· Immediately after removing the plastic bag, a slight odor may occur. This odor is not harmful for filter performance or human exposure.
The product makes a clicking or ticking sound.
· The product may make clicking or ticking sounds when it is generating ions.
The air quality monitor is blue even when the air is not clean.
· The air may have been dirty when the product was plugged in. Unplug the product, wait one minute, and then plug the product in again.
The air quality monitor is red even when the air is clean.
· Dirty or clogged the sensitive dust sensor openings interfere with sensor operation. Gently clean the sensor filter or the back panel.
The air quality monitor changes color frequently.
· The air quality monitor automatically changes color when the sensitive dust sensor and odor sensor detect impurities. If you are concerned about the change, you can change sensor sensitivity. (Page 12)

The filter maintenance indicator light is on.
· Whenever after performing maintenance of the filters, connect the power cord to an outlet and press POWER ON/OFF button, then press the FILTER RESET button. (Page 13)
The front display is turned off.
· When light control is set to “Turn off”, the light is always off. If you do not want the light to be off, set light control to “Auto” or “Dim” setting. (Page 12)
The product’s display does not match weather report or another hygrometer or thermometer in the room.
· Outdoor and indoor as well as the home environment (the volume of traffic nearby, number of stories in home, etc.) may cause a reading different than those data.
· There is a difference in the level within the same room.
When should sensor sensitivity be changed?
Please change sensor sensitivity as follows according to each case.
Light sensor · Change to “Low” when the front display still
lights up brightly even if it turns dark in the room. · Change to “High” when the front display lights up dark even if it is bright in the room. Sensitive dust sensor · Change to “Low” when PM2.5, Dust or Air Quality Monitor displays in red frequently. · Change to “High” when PM2.5 or Dust Monitor doesn’t light up or Air Quality Monitor stays in blue even if it is dusty in the room. Odor sensor · Change to “Low” when Odor Monitor displays in red frequently. · Change to “High” when Odor Monitor doesn’t light up even if there is some odor in the room.

EN-16

ENGLISH

ERROR DISPLAY

Flash quickly

· The communication between SHARP server and the air purifier is not available. Please check the Wi-Fi Connect Guide for details.
· The concentration of Plasmacluster ion is descending. Maintain the electrode section of the Plasmacluster ion generating unit. (Page 15)

· Is the Plasmacluster ion generating unit inserted properly? Pull out the Plasmacluster ion generating unit and insert it to the end again, and then operate again.
· Unplug the product, wait one minute, and then plug the product in again.

SPECIFICATIONS

Model Power supply
Fan Speed Operation

Fan Speed Adjustment Rated Power (W) Fan Speed (CFM) Noise Level (dBA)*1

Standby Power (W)

Recommended Room Size*2

CADR (Dust / Smoke / Pollen)

Filter type

Dust collection Deodorization

Cord Length

Dimensions

Weight

FX-J80U

120 V / 60 Hz

MAX

MED

SLEEP

70

27

3.2

321

170

35

49

45

15

0.9 (When Wi-Fi adapter is ON.) 0.7 (When Wi-Fi adapter is OFF.)
502 sq. ft. (47 m2)

334 / 324 / 361

True HEPA Filter

Active Carbon Deodorizing Filter

6.6 ft. (2.0m)

16.4 in. (W) × 11.5 in. (D) × 28.7 in. (H) (416 mm (W) × 291 mm (D) × 728 mm (H))
23.8 lbs. (10.8 kg)

1 Noise level is measured based on the JEM 1467 standard of the Japan Electrical Manufacturers’ Association.
2 Size of a room which is appropriate for operating the product at maximum fan speed.

Standby Power This product consumes a minimal amount of power while in standby mode. For energy saving, unplug the power cord when the product is not in use.

EN-17

OTHER SETTINGS 1

Please refer to the Wi-Fi Connect Guide for how to connect and pair your smart device to your product.
SAFETY / PRECAUTIONS
WARNING
In case of remote operation from outside, you may not be able to check air purifier current condition or the area around it and the situation concerning anyone possibly staying there, so please adequately confirm safety before use.
· Make sure the electric plug is fully inserted into a power socket, and there is no dust on the plug or in the socket hole. (It may cause heat, combustion, fire, etc., due to poor contact or contact failure)
· Make sure beforehand that although there are some wind changes, no negative impact will occur to the environment inside the room. (such as whether there is anything flying easily in the wind) Because the wind may cause something to fall down, resulting in fires, wounds, defacement of household belongings.
CAUTION FOR USE
· Agreement with “Terms of Service” is needed to use App.
· App will be periodically revised because of version upgrade.
· Screens and illustrations in this book are for explanation, there are some differences to the real product.
· In the case of bad connection, the App may not be able to control the air purifier. The current operation of the air purifier may not be accurately reflected on the App.
· Locking smartphone display is recommended to avoid wrong operation.
· Although the App is free, communications expenses for download of dedicated App and operation with smartphone or tablet are customer’s obligation.
CAUTION FOR Wi-Fi
Caution for usage about electrical wave

At the following places, it is likely electrical wave cannot reach or is disconnected: Inside of the building made with concrete, reinforcing steel or metal / near the obstruction / near the wireless communications device applying the same frequency. · Wi-Fi of this product corresponds to channel 1 – 13. It’s not available to communicate with the routers set up to other channels.
Caution for personal information (related to Security)
· Using Wi-Fi device has the possibility of interception as long as using electrical wave regardless of secret code setting.
· Wi-Fi has the advantage of free LAN connection in the service area because of the communication between this product and the router applying electrical wave. On the other side, intercept of communication or unfair intrusion are likely to occur because electrical wave reaches everywhere in the certain area through the obstructions (e.g. walls).
· Do not connect to the device or network without App to authority.
· The Wi-Fi function of this product should be initialized in case of disposal or handover to a third person.
· The Wi-Fi function of the unit should be initialized in case of handover from a third person to avoid illegal access of outsider.
How to set Wi-Fi ON / OFF after completing the initial settings
When turning off Wi-Fi

Go off
Press for 3 sec.
When turning on Wi-Fi again Refer to Page 4 – 7 of the air purifier Wi-Fi Connect Guide and set up the connection with the router again.

· In case of the usage at the following place, the operation cannot be guaranteed : Near Bluetooth® wireless communications device using the same
frequency (2.4GHz) as this product or specified low power wireless device. Also in the place like
magnetic field of the device such as microwave oven, or the place with static electricity or the place radio disturbance is occurred, it may not be available temporarily due to weak electrical wave. · Wireless connection and performance cannot be guaranteed for all routers or housing environment.

· If the product is already registered to your smartphone, you do not need to register again.
NOTE
· Wi-Fi ON / OFF can also be set from ” : Wi-Fi adapter ON/OFF”. (Page 19) In this case, Wi-Fi connection with the router will be automatically restored.
· Reconnection to the Wireless Router may take a few minutes to complete, after turning Wi-Fi on again.

EN-18

OTHER SETTINGS 2

ENGLISH

HOW TO CHANGE VARIOUS SETTINGS 1

You can change the functions in the table below. Follow Steps 1 – 4 to select the Function.

Step 1. Turn the product OFF.

Wi-Fi adapter ON/OFF
1. Select by following Steps 1 – 4.

Step 2.

2. Select “Setting Number”.

Press for 3 sec.

Step 3. Select .

Set

Step 4. Select “Function Number”.

GO BACK

GO FORWARD

or

No

Function

Page

Wi-Fi adapter ON/OFF

19

Wi-Fi connection with a router 19

Link settings with a smartphone 20

Initialization of Wi-Fi function 20

Update

20

Confirmation of MAC address 20

Display Wi-Fi network status

21

AP(Access Point) mode

21

Step 5. Please refer to page 19 – 21 for the detail of each functions.

Set

Step 6. Finish the setting.

OFF: Stoppage of Wi-Fi function

ON: Start the Wi-Fi function

3. Complete

· When

is selected, the square rotates

on the display until the setting is completed.

When setting is completed,

is displayed.

Wi-Fi connection with a router

1. Select by following Steps 1 – 4.

2. After is displayed, press the Wi-Fi Protected Setup (WPS) button of the router.

Blink

Blink

Once connected, receiver level will be displayed.

weak

strong

Light up

A connection error is occuring if

is displayed.

Please confirm the router and try again.

3. Complete

Turn off

EN-19

OTHER SETTINGS 3

HOW TO CHANGE VARIOUS SETTINGS 2

Link settings with a smartphone

1. Select by following Steps 1 – 4 on page 19.
2. After is displayed, start the App and register the air purifier.

Setting up

Complete

Blink

A connection error is occuring if

is displayed.

Please confirm the router and try again.

3. Complete

Initialization of Wi-Fi function

Update
1. Start the App then tap ” ” at the “Home” screen and select “Update”.

2. Select by following Steps 1 – 4 on page 19.
3. will be displayed.
4. Follow instructions on the App screen.

will be blinking during update.

A connection error is occuring if

is displayed.

Please confirm the router and try again.

5. Air purifier will automatically

go off after completion of the

update.

Go off

It may take a few minutes to complete the update.

1. Select by following Steps 1 – 4 on page 19.

2. After is displayed press “AUTO” button.

Initializing Complete

Blink

Confirmation of MAC address
1. Select by following Steps 1 – 4 on page 19.
2. Press Plasmacluster Express Clean button to display MAC address.

A connection error is occuring if

is displayed.

Please confirm the router and try again.

3. Complete

For example : In case MAC address is “12 : 34 : 56 : AB : CD : EF”

· Please delete the device registration from the App when initializing the air purifier which is already connected to the Wi-Fi.

3. Complete

EN-20

ENGLISH

OTHER SETTINGS 4

HOW TO CHANGE VARIOUS SETTINGS 3

Display Wi-Fi network status
1. Select by following Steps 1 – 4 on page 19.
2. After displaying for a few seconds, network status of Wi-Fi adapter will be displayed.
Connection is stable
Wi-Fi adapter is off Please turn on Wi-Fi adapter.
Router is not registered Please perform the Wi-Fi connection with the router.
Link settings with the App is not performed Please perform the link setting with the smartphone.
Wi-Fi adapter network error Please turn off Wi-Fi adapter and turn on again after a while.
Network error between the air purifier and the router
Please confirm the network status of the router.
Network service error Please turn off the air purifier and confirm the internet status, then try again.

AP (Access Point) mode

1. Select by following Steps 1 – 4 on page 19.
2. Perform Wi-Fi connection of the air purifier and the router based on the App screen.
Refer to the App or the Wi-Fi Connect Guide for further operations.

and

blinks while setting the

connection between the product and the router.

Once connected, receiver level will be displayed.

weak

strong

Light up

A connection error is occuring if

is displayed.

Please confirm the router and try again.

3. Complete

SPECIFICATIONS

Wireless LAN: IEEE802.11b/g/n Frequency range: 2.4GHz frequency band
EN-21

Intellectual property rights for this product 1

Software structure
Software installed in this product is structured with multiple independent software components, each of them has our or third-party’s copyright.
Software of our development and free software
Among the software components of this product, for software we developed or created and incidental documents has our copyright. And they are protected by copyright law, international regulation and other related laws. Also this product uses software components distributed as free software with third- party’s copyright.
Obligation of license indication
Some software components installed in this product are required to indicate the license by those copyright holders. License indications of such software components are as below:
Expat Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Wslay The MIT License Copyright (c) 2011, 2012 Tatsuhiro Tsujikawa
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2014 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: – Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Iw-IP Copyright (c) 2001, 2002 Swedish Institute of Computer Science. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This file is part of the lwIP TCP/IP stack.
Author: Adam Dunkels adam@sics.se
JSMN Copyright (c) 2010 Serge A. Zaitsev
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
mbedTLS Copyright (C) 2006-2015, ARM Limited, All Rights Reserved
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
wpa supplicant Copyright (c) 2003-2017, Jouni Malinen j@w1.fi and contributors All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
newLib (1) Red Hat Incorporated

EN-22

Intellectual property rights for this product

ENGLISH

Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved.
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc.
(2) University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California. All rights reserved.

in Japan, toll free. The direct dial number is 512-462-4118.
Advanced Micro Devices, Inc. 29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263
(7) Sun Microsystems
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(8) Hewlett Packard
(c) Copyright 1986 HEWLETT-PACKARD COMPANY
To anyone who acknowledges that this file is provided “AS IS” without any express or implied warranty:
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.
(9) Hans-Peter Nilsson
Copyright (C) 2001 Hans-Peter Nilsson
Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

(3) David M. Gay (AT&T 1991, Lucent 1998)

(11) Christopher G. Demetriou

The author of this software is David M. Gay.
Copyright (c) 1991 by AT&T.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. ——————————————————————The author of this software is David M. Gay.
Copyright (C) 1998-2001 by Lucent Technologies All Rights Reserved
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that the copyright notice and this permission notice and warranty disclaimer appear in supporting documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.

Copyright (c) 2001 Christopher G. Demetriou All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(12) SuperH, Inc.

LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
(4) Advanced Micro Devices
Copyright 1989, 1990 Advanced Micro Devices, Inc.
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE.

Copyright 2002 SuperH, Inc. All rights reserved
This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH.
SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE. IN NO EVENT SHALL SUPERH BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE.
So that all may benefit from your experience, please report any problems or suggestions about this software to the SuperH Support Center via e-mail at softwaresupport@superh.com .
SuperH, Inc. 405 River Oaks Parkway San Jose CA 95134 USA
(13) Royal Institute of Technology

So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-2929-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, or 0031-11-1129

Copyright (c) 1999 Kungliga Tekniska Högskolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved.

EN-23

Intellectual property rights for this product 3

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(17) S. L. Moshier

3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(14) Alexey Zelkin

Author: S. L. Moshier.
Copyright (c) 1984,2000 S.L. Moshier
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.
(18) Citrus Project
Copyright (c)1999 Citrus Project, All rights reserved.

Copyright (c) 2000, 2001 Alexey Zelkin phantom@FreeBSD.org All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(15) Andrey A. Chernov

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(19) Todd C. Miller
Copyright (c) 1998 Todd C. Miller Todd.Miller@courtesan.com All rights reserved.

Copyright (C) 1997 by Andrey A. Chernov, Moscow, Russia. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(16) FreeBSD
Copyright (c) 1997-2002 FreeBSD Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(26) Mike Barcroft
Copyright (c) 2001 Mike Barcroft mike@FreeBSD.org All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

EN-24

Intellectual property rights for this product 4

ENGLISH

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(35) – ARM Ltd (arm and thumb variant targets only)
Copyright (c) 2009 ARM Ltd All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the company may not be used to endorse or promote products derived from this software without specific prior written permission.

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(3) DJ Delorie
Copyright (C) 1993 DJ Delorie All rights reserved.
Redistribution, modification, and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms.
This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
(4) (formerly GPL for fr30)

THIS SOFTWARE IS PROVIDED BY ARM LTD “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(41) Ed Schouten – Free BSD
Copyright (c) 2008 Ed Schouten ed@FreeBSD.org All rights reserved.

The GPL is no longer applicable to the fr30 platform. The piece of code (syscalls.c) referencing the GPL has been officially relicensed.
(5) Advanced Micro Devices
Copyright 1989, 1990 Advanced Micro Devices, Inc.
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.
Advanced Micro Devices, Inc. 29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263
(8) Sun Microsystems
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
(9) Hewlett Packard

libgloss (1) Red Hat Incorporated
Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved.
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc. . (2) University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California. All rights reserved.

(c) Copyright 1986 HEWLETT-PACKARD COMPANY
To anyone who acknowledges that this file is provided “AS IS” without any express or implied warranty:
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.
(10) Hans-Peter Nilsson
Copyright (C) 2001 Hans-Peter Nilsson
Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
(14) – National Semiconductor Corporation
Copyright (c) 2004 National Semiconductor Corporation
The authors hereby grant permission to use, copy, modify, distribute, and license this software and its documentation for any purpose, provided that existing copyright notices are retained in all copies and that this notice is included verbatim in any distributions. No written agreement, license, or royalty fee is required for any of the authorized uses. Modifications to this software may be copyrighted by their authors and need not follow the licensing terms described here, provided that the new terms are clearly indicated on the first page of each file where they apply.

References

• Simply Better Living – SHARP | Simply Better Living
• Sharp Electronics | SharpUSA
• Apache License, Version 2.0
• Licenses – Open Source Initiative
• Sharp Electronics | SharpUSA
• Sharp Electronics - Sign in
• Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>