SUPERATV XP 900 Polaris Ranger Crew Roof Instruction Manual
- October 27, 2023
- SUPERATV
Table of Contents
SUPERATV XP 900 Polaris Ranger Crew Roof
Parts Description
- This item is not returnable if the protective film has been removed.
- Test fit to the cage to confirm fitment before removing film.
Item Description
A| Front Plate
B| Rear Plate
C| Middle Plate
D| Rear
E| Front
F| Right Panel
G| Center Panel
H| Left Panel
Item Description
J| Clamp x 2
K| Bracket x 6
L| Middle Mount Bracket x 2
M| Center Panel Bracket
Need help with your installation?
E-mail: [email protected]
Phone: 1-855-743-3427
Web: www.superatv.com
Timmimg:
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Roof Cleaning
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Thoroughly rinse Roof to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Roof with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Roof dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof
.
Installation Instructions
Seal and Gasket installation: set aside when completed.
- – Install provided Flat Seal to Front Plate (A), Rear Plate (B), and Middle Plate (C).
- Install (1) piece of provided Gasket to each Middle Mount Bracket (L) as shown.
Panel prep: set aside when completed.
- Place Left Panel (H) onto Frame and align with stock hole.
- Mark and drill new hole. Hole should be large enough for Ø6mm bolt.
- Repeat for all Panels.
- NOTE: Center Panel location on Frame will not have a stock hole to locate.
Panel installation: set aside when completed.
- Install provided Gasket around edges of all cutouts.
- Install Left (H) and (Right (F) Panels with hardware shown.
- Se following page for Center Panel (G) installation.
- Plug holes in Frame with provided Shanks. Not all models will use supplied quantities.
- Install Center Panel (G) to Frame with hardware shown.
- Secure Center Panel (G) to Center Panel Bracket (M) with hardware shown. Center Panel Bracket (M) goes against Frame inside vehicle.
When installing components, do not tighten any hardware completely unless noted.
- Install Clamps (J) to Center Bar of machine with hardware shown.
- Install Rear Plate (B) to machine with hardware shown.
- Install Front (E) and Rear (D) to Middle Plate (C).
- Install one continuous piece of Seal down sides of Front (E) and Rear (D) as shown.
Soak Seal in hot water before cutting or installing to increase flexibility
.
- Secure Roof and Front Plate (A) to machine.
- Secure Roof and Front Plate (A).
- Secure Roof to Middle Mount Brackets (L) and Rear Plate (B).
- Install Brackets (K) to Roof with hardware shown.
Tighten all hardware completely
Documents / Resources
|
SUPERATV XP 900 Polaris Ranger Crew
Roof
[pdf] Instruction Manual
XP 900 Polaris Ranger Crew Roof, XP 900, Polaris Ranger Crew Roof
---|---