SUPERATV XP 1000 Forward Offset Front High Clearance A-Arms Instruction Manual
- October 27, 2023
- SUPERATV
Table of Contents
IN-AA-P-GENXP-1.5 4/27/2021
2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427
INSTALLATION INSTRUCTIONS
Forward Offset Front High Clearance A-Arms: for Polaris General ® XP 1000
XP 1000 Forward Offset Front High Clearance A-Arms
| Item | Description | Item | Description |
|---|---|---|---|
| A | Upper Right | C | Upper Left |
| B | Lower Right | D | Lower Left |
A Press or Ball Joint tool is required to remove and install Ball Joints.
Liability Statement SuperATV’s ® products are designed to best fit the user’s
ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory
or aftermarket parts will void any warranty provided by SuperATV ® and is not
recommended. SuperATV’s ® products could interfere with other aftermarket
accessories. If user has aftermarket products on the machine, contact SuperATV
® to verify that they will work together. Although SuperATV ® has thousands of
satisfied customers, user should be aware that installing lift kits, long
travel, or suspension kits, tires, etc. will change the ride of the machine
and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death.
No warranty or representation is made as to this product’s ability to protect
users from severe injury or death. SuperATV ® urges operators and occupants to
wear a helmet and appropriate riding gear at all times. By purchasing and
installing SuperATV ® products, user agrees that should damage occur, SuperATV
® will not be held responsible for loss of time, use, labor fees, replacement
parts, or freight charges. SuperATV ® , nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential
damages that result from any product purchased from SuperATV ® . The total
liability of seller to user for all damages, losses, and causes of action, if
any, shall not exceed the total purchase price paid for the product that gave
rise to the claim. SuperATV ® will warranty only parts provided by SuperATV ®
. Any damage or problems with OEM housings, bearings, seals, or other
manufacturers’ products will not be covered by SuperATV ® . SuperATV ® parts
and products are not warranted if item was not installed properly, misused, or
modified. Installing, adding, modifying, or fabricating any factory or
aftermarket product to your ATV/UTV may violate certain local, state, and
federal laws.
Be advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product.
You must abide by all local, state, and federal laws, including but not
limited to vehicle safety, traffic laws, and ordinances.
It is your responsibility to know the laws and how they apply to you. The
Buyer is responsible to fully understanding the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV ® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV violation thereof. ® harmless from any
violation thereof.
A-Arms Prep:
PIVOT BLOCK SETTINGS
– Place new A-Arms onto a flat surface and verify the dimension shown.
– Negative 1° camber setting is achieved when Pivot Blocks are set to this
dimension.
– See last page for additional camber information.
install Steering Stops
The rack and Pinion showed off the machine for clarity only
– Install Steering Stop onto Shaft.
– Repeat for opposite side.
(driver-side installation shown)
– Install Lower Left (D) to Frame with stock hardware; keep Nuts loose until
all final adjustments have been completed.
– Install Upper Left (C) to Frame with stock hardware; SuperATV recommends
using Loc-Tite on Nuts.
–
Install Sway Bar Links to Upper A-Arms with stock hardware.
– Install Shocks to Upper A-Arms with stock hardware.
– Install Knuckles to Arms with stock hardware; keep Lower Nuts loose until
all final adjustments have been completed.
– Install Hub and Tie Rod Ends.
– Reinstall Tires and check Camber settings; see last page.
– Tighten Nuts completely. SuperATV recommends using Loc-Tite on Nuts.
– Secure Brake Lines to Upper A-Arms with components shown.
INSTALLATION INSTRUCTIONS
Swaged Straight Heavy Duty Tie Rod Kit
Read instructions and
view illustrations before beginning.
– Remove Jam Nuts from Ball and Sockets.
– Install Ball and Sockets to Rack and Pinion. Use Loctite.
– Install Boots to Rack and Pinion and secure with Zip Ties.
Use a lubricant to ease installation.
– Reinstall Jam Nuts to Ball and Sockets
– Install Tie Rod Shafts to Ball and Sockets.
– Install Tie Rod Ends to Tie Rod Shafts
– Use the hardware shown when securing Tie Rod Ends to Spindles. Install to
the same location as stock.
Liability Statement
SuperATV’s ® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV ® and is not recommended.
SuperATV’s ® products could interfere with other aftermarket accessories. If
user has aftermarket products on the machine, contact SuperATV ® to verify
that they will work together. Although SuperATV ® has thousands of satisfied
customers, user should be aware that installing lift kits, long travel, or
suspension kits, tires, etc. will change the ride of machine and may increase
maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV ® urges operators and occupants to wear a helmet and appropriate
riding gear at all times. By purchasing and installing SuperATV ® products,
user agrees that should damage occur, SuperATV ® will not be held responsible
for loss of time, use, labor fees, replacement parts, or freight charges.
SuperATV ® , nor any 3rd party, will not be held responsible for any direct,
indirect, incidental, special, or consequential damages that result from any
product purchased from SuperATV ® . The total liability of seller to user for
all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV ® will warranty only parts provided by SuperATV ® . Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV ® . SuperATV ® parts and products are not
warranted if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws.
Be advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law.
The Buyer is solely and exclusively legally and personally responsible for any
violation of the law by the installation or use of the product. You must abide
by all local, state, and federal laws, including but not limited to vehicle
safety, traffic laws, and ordinances.
It is your responsibility to know the laws and how they apply to you. The
Buyer is responsible to fully understanding the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV ® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV ® harmless from any violation thereof.
CAMBER
– Tires must have equal air pressure before making adjustments.
– Adjustments to be made after all suspension components have been completely
assembled.
– Tires must not be in contact with the ground when making adjustments.
– Perform adjustments in small increments.
Adjusting Camber:
– Remove A-Arms from Frame and turn Pivot Blocks to adjust camber. Reinstall
Arms.
– Lower the machine and settle suspension components by rolling the machine
back and forth several feet at a time.
– Check settings and make small adjustments as needed.
– Each time an adjustment is made, the machine must be rolled back and forth
to settle suspension components.
– Once desired setting is achieved, tighten the hardware completely. Loc-tite
on Nuts is recommended.
LOWER: Too much positive camber: adjust Pivot Blocks OUT. Too much
negative camber: adjust Pivot Blocks IN. note: 2 full turns is 1°
UPPER A-ARMS: Too much positive camber: adjust Pivot Blocks IN. Too much
negative camber: adjust Pivot Blocks OUT.note: 2 full turns is 1°
IN-Arm-Settings A NEGATIVE CAMBER SETTING OF 1° to 2° IS RECOMMENDED.
Need help with your installation?
sales@superatv.com
www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
1-855-743-3427
9:00am – 2:00pm EST Saturday © 2021SuperATV.com ®
. All Rights Reserved.
Documents / Resources
|
SUPERATV XP 1000 Forward Offset Front High Clearance
A-Arms
[pdf] Instruction Manual
XP 1000 Forward Offset Front High Clearance A-Arms, XP 1000, Forward Offset
Front High Clearance A-Arms, Front High Clearance A-Arms, High Clearance
A-Arms, Clearance A-Arms, A-Arms
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>