INTIMSCAN360 Intimidator Scan
User Manual
Table of Contents
TABLE OF CONTENTS
1. Before You Begin …………………………………………………………….. 1
What Is Included ………………………………………………………………………………. 1 Unpacking
Instructions………………………………………………………………………. 1
Claims ……………………………………………………………………………………………………… 1
Text Conventions ……………………………………………………………………………… 1 Symbols
………………………………………………………………………………………….. 1 Disclaimer
……………………………………………………………………………………….. 1 Intellectual Property
………………………………………………………………………….. 1 Safety
Notes…………………………………………………………………………………….. 2
2. Introduction …………………………………………………………………….. 3
Product Overview……………………………………………………………………………… 3 Product Dimensions
………………………………………………………………………….. 3
3. Setup ………………………………………………………………………………. 4
AC Power ………………………………………………………………………………………… 4
Fuse Replacement …………………………………………………………………………………….. 4 Power
Linking……………………………………………………………………………………………. 4
Mounting …………………………………………………………………………………………. 5
Orientation………………………………………………………………………………………………… 5 Rigging
…………………………………………………………………………………………………….. 5
4. Operation ………………………………………………………………………… 6
Control Panel Operation…………………………………………………………………….. 6 Menu Map
……………………………………………………………………………………….. 6 Configuration (DMX)
…………………………………………………………………………. 7
Starting Address………………………………………………………………………………………… 7 DMX
Personalities……………………………………………………………………………………… 7
Gobos……………………………………………………………………………………………… 7 DMX Channel Assignments and Values
………………………………………………. 8
DMX Values ……………………………………………………………………………………………… 8
Configuration (Standalone) ………………………………………………………………… 10
Automatic Programs…………………………………………………………………………………… 10 Sound-Active Mode
……………………………………………………………………………………. 10 Sound
Sensitivity……………………………………………………………………………………….. 10 Manual
Mode…………………………………………………………………………………………….. 10
Configuration (Settings) …………………………………………………………………….. 11
Pan Reverse……………………………………………………………………………………………… 11 Tilt Reverse
………………………………………………………………………………………………. 11 Screen
Reverse…………………………………………………………………………………………. 11 Signal
Loss……………………………………………………………………………………………….. 11
Indicator……………………………………………………………………………………………………. 11 Flash if
DMX……………………………………………………………………………………………… 11 Factory Reset
……………………………………………………………………………………………. 12 System Information
……………………………………………………………………………………. 12
IRC-6 Infrared Remote Control …………………………………………………………… 12
IRC-6 Operation ………………………………………………………………………………………… 12
Master/Slave Mode …………………………………………………………………………… 13
5. Maintenance…………………………………………………………………….. 14
Product Maintenance ………………………………………………………………………… 14
6. Technical Specifications ………………………………………………….. 15
Returns……………………………………………………………………………….. 16 Contact Us
………………………………………………………………………….. 17
Intimidator Scan 360 User Manual Rev. 2
Before You Begin
1. Before You Begin
What Is Included
· Intimidator Scan 360 · Power cord
· Quick Reference Guide
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure
all the parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear
damaged from shipping, or show signs of mishandling, notify the carrier
immediately, not Chauvet. Failure to report damage to the carrier immediately
may invalidate your claim. In addition, keep the box and contents for
inspection. For other issues, such as missing components or parts, damage not
related to shipping, or concealed damage, file a claim with Chauvet within 7
days of delivery.
Text Conventions
Convention 1512 50/60
Settings
ON
Meaning A range of values A set of values of which only one can be chosen A
menu option not to be modified A key to be pressed on the product’s control
panel A value to be entered or selected
Symbols
Symbol
Meaning
Electrical warning. Not following these instructions may cause electrical
damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following
these instructions may make the product not work, cause damage to the product,
or cause harm to the operator.
Important installation or configuration information. The product may not
function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in
all respects. However, Chauvet assumes no responsibility and specifically
disclaims any and all liability to any party for any loss, damage or
disruption caused by any errors or omissions in this document, whether such
errors or omissions result from negligence, accident or any other cause.
Chauvet reserves the right to revise the content of this document without any
obligation to notify any person or company of such revision, however, Chauvet
has no obligation to make, and does not commit to make, any such revisions.
Download the latest version from www.chauvetdj.com.
Intellectual Property
The works of authorship contained in this manual, including, but not limited
to, all design, text and images are owned by Chauvet. © Copyright 2021 Chauvet
& Sons, LLC. All rights reserved. Electronically published by Chauvet in the
United States of America. CHAUVET, the Chauvet logo, and Intimidator Scan 360
are registered trademarks or trademarks of Chauvet & Sons LLC (d/b/a Chauvet
and Chauvet Lighting) in the United States and other countries. Other company
and product names and logos referred to herein may be trademarks of their
respective companies.
Intimidator Scan 360 User Manual Rev. 2
Page 1 of 17
Before You Begin
Safety Notes
· This product is not intended for permanent installation. · Always connect
the product to a grounded circuit to avoid the risk of electrocution. · Always
disconnect the product from the power source before cleaning or replacing the
fuse. · Avoid direct eye exposure to the light source while the product is on.
· Make sure the power cord is not crimped or damaged. · Never disconnect the
product from power by pulling or tugging on the cord. · If mounting the
product overhead, always secure to a fastening device using a safety cable. ·
Make sure there are no flammable materials close to the product when
operating. · Do not touch the product’s housing when operating because it may
be very hot.
· The voltage of the outlet to which you are connecting this product must be
within the range stated on the decal or rear panel of the product.
· The product is for indoor use only! (IP20) To prevent risk of fire or shock,
do not expose the product to rain or moisture.
· Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
· Be sure that no ventilation slots on the product’s housing are blocked. ·
Never connect the product to a dimmer or rheostat. · Make sure to replace the
fuse with another of the same type and rating. · Never carry the product from
the power cord or any moving part. · The maximum ambient temperature is 104 °F
(40 °C). Do not operate this product at higher
temperatures. · In the event of a serious operating problem, stop using the
product immediately. · Do not open this product. It contains no user-
serviceable parts. · To eliminate unnecessary wear and improve its lifespan,
during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If the product is sold to someone else,
be sure that they also receive this document.
Page 2 of 17
Intimidator Scan 360 User Manual Rev. 2
Introduction
2. Introduction
Product Overview
Mounting bracket
Mirror
Lens
Display
Safety cable pass-through
Bracket adjustment knob
Menu buttons
Product Dimensions
DMX in/out
Power in/out
6 in 155 mm
Intimidator Scan 360 User Manual Rev. 2
A
16.3 in 415 mm
10 in 255 mm
Page 3 of 17
Setup
3. Setup
AC Power
The Intimidator Scan 360 has an auto-ranging power supply and it can work with
an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s
power requirements (circuit breaker, power outlet, and wiring), use the
current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating
indicates the product’s average current draw under normal conditions.
· Always connect the product to a protected circuit (a circuit breaker or
fuse). Make sure the product has an appropriate electrical ground to avoid the
risk of electrocution or fire.
· To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit,
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1. Disconnect the product from power. 2. Wedge the tip of a flat-head
screwdriver into the slot of the fuse holder. 3. Pry the fuse holder out of
the housing. 4. Remove the blown fuse from the holder and replace with a fuse
of the exact same type and rating. 5. Insert the fuse holder back in place and
reconnect power.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap
Disconnect the product from the power outlet before replacing the fuse.
Power Linking
The product provides power linking via the outlets located in the back of the
product. See the diagram below for further explanation. Power Linking Diagram
Additional products
3rd Product
2nd Product
1st Product
Power Source
You can power link up to 4 Intimidator Scan 360 products on 120 VAC or up to 7
products on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the local Chauvet distributor as power linking connectors and
requirements may differ in your country or region.
Page 4 of 17
Intimidator Scan 360 User Manual Rev. 2
Setup
Mounting
Before mounting the product, read and follow the safety recommendations
indicated in the Safety Notes.
Orientation
The Intimidator Scan 360 may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
· Before deciding on a location, always make sure there is easy access to the
product for maintenance and programming.
· Make sure adequate ventilation is provided around the product. · Make sure
that the structure or surface onto which you are mounting the product can
support the
product’s weight. (see the Technical Specifications) · When mounting the
product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss. · When rigging the
product onto a truss, use a mounting clamp of appropriate weight capacity. ·
When power linking multiple products, mount the products close enough for
power linking cables to
reach. · The rubber feet also serve as floor supports and allow for surface
mounting. When mounting the
product on the floor, make sure that the product and cables are away from
people and vehicles. Mounting Diagram
Mounting clamp
(such as CLP-10 from Chauvet)
Mounting bracket
Safety cable
(such as CH-05 from Chauvet)
Safety cable pass-through
When using only one mounting clamp with this fixture, you must use a clamp
with a captive bolt to prevent accidental loosening.
Intimidator Scan 360 User Manual Rev. 2
Page 5 of 17
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath
the display. Please refer to the Product Overview to see the button locations
on the control panel.
Button Function
