cecotec 500 X Vacuum Cleaner Instruction Manual

cecotec 500 X Vacuum Cleaner

PARTS AND COMPONENTS

1. Suction base release button
2. Vacuuming tube release button
3. Dust tank release button
4. High-efficiency filter
5. Power push button
6. Power button
7. Power supply
8. Battery
9. Power adapter
10. Vacuuming Flex tube
11. Suction base
12. Narrow brush for furniture and corners
13. Wide brush for furniture and corners
14. Wall bracket
15. Wall plugs
16. Screws
17. Dust tank
18. Jalisco brush
19. Silicone and bristles brush
20. Adhesive for wall bracket
21. Water tank

BEFORE USE

Take the product out of the box.
Check for any visible damage, if any is observed, contact as soon as possible the Technical Support Service of Cecotec for advice or reparation.

PRODUCT ASSEMBLY

Vacuuming tube and suction base assembly.
To install the suction base into the vacuuming tube, align both of them making sure the tab on the suction base matches the guides on the tube, and introduce one into the other until they are firmly fixed. To disassemble them, press the suction base release button and pull from the vacuuming tube while you hold the suction base.

Note : When assembling these 2 parts, make sure the handle and the brush are facing the same direction.
Use the Flex tube to reach and clean the most difficult areas and dirt. To bend the tube, press the Flex button.
Fig. 2

Battery and handheld vacuum cleaner assembly
Introduce the battery in the slot located in the handheld vacuum cleaner. Once it is introduced, move it slightly to ensure it is properly assembled in place.
Fig. 3

Following the illustration below, keep the vacuuming tube vertically, align the tab on the vacuuming tube with the guides in the handheld vacuum cleaner and introduce the tube.

Dust tank assembly
To assemble the dust tank, first separate the handheld vacuum cleaner from the vacuuming tube.
Then, press the vacuuming tube release button with one hand and, holding from the handle with the other one, turn the dust tank anticlockwise to the lock position indicated on the dust tank edge.
To disassemble the dust tank, turn it clockwise until it reaches the unlock position.
Fig. 4

Suction base, vacuuming tube and handheld vacuum cleaner installation
To complete the full installation of the device, hold the vacuuming tube with the suction base assembled upright and introduce the tube in the handheld vacuum cleaner as shown on the illustration.
Fig. 5

OPERATION

Handheld vacuum cleaner
Once the handheld vacuum cleaner has been disassembled from the vacuuming:
Press the On/off button to turn the device on.
Press the power push button to select the desired power level.
It will automatically operate in Eco mode. The power level can be adjusted at any moment by pressing this button.
Press once to switch to Daily mode.
Press again to operate it at Turbo mode.
Press the On/off button to turn the device off.
Fig. 6

Upright vacuum cleaner
Assemble the vacuuming tube (see section 3 “Product assembly”)
Press the On/off button to turn the device on.
Press the power push button to select the desired power level.
It will automatically operate in Eco mode. The power level can be adjusted at any moment by pressing this button.
Press once to switch to Daily mode.
Press again to operate it at Turbo mode.
Press the On/off button to turn the device off.

Accessories
This device includes different accessories that allow cleaning different types of surfaces, objects and dirt. Some of them are suitable for the upright vacuum cleaner, and others are preferably used with the handheld one.

Jalisco brush
Assemble this brush to the upright vacuum cleaner. This brush is designed especially for cleaning hard floors, but can be used to clean efficiently soft floors too. The brush counts on a protection system that avoids tangles and prevents the device from being damaged. As the brush stops rotating and the device stops operating automatically when it vacuums big objects or excessive dirt.
Fig. 7

Silicone and bristles brush
Interchangeable brush made of silicone and bristles, ideal for cleaning carpets and pet hair.
This accessory is used with the upright vacuum cleaner.

2-in-1 wide brush for furniture and corners
This accessory is used with the handheld vacuum cleaner and allows cleaning furniture without damaging it and reaching less accessible dirt in corners.
Fig. 8

Wall bracket
This product includes a wall bracket that allows hanging the vacuum cleaner from the wall. The same bracket has different accessory holders that allow storing accessories while not in use.
It can be assembled with screws (included with the product), or with an adhesive (included with the product).
When using the adhesive, make sure to use it on a clear flat surface.
Also make sure that the suction base rests on the floor when hang to avoid the wall bracket from falling.
Fig. 9

Charging
The device can be charged in 2 different ways. It can be charged directly through the handheld vacuum cleaner or the battery can be removed and charged separately.
It is important to charge it when the battery is low. While charging, the battery indicator will turn on red, and it will turn green when battery is fully charged again.
Disconnect it from the power adapter when the battery indicator is lit up in green.
Fig. 10

CLEANING AND MAINTENANCE

Do not use abrasive scouring pads, powders or cleaners to clean the product.
Use a soft, dampened and clean cloth to clean the product’s outer housing.
Do not let water enter into the vacuum cleaner.
Keep the appliance in a cool, dry place and out of reach from children.
Do not immerse the device in water and do not clean any of its parts in the dishwasher.

Dust tank
To empty the dust tank, first disassemble the handheld vacuum cleaner from the rest of the unit. Use the tab on the dust tank to open its cover and empty it. If necessary, shake it gently to remove all the dust.
Fig. 11

To clean it, press the dust tank release button and turn the dust tank anticlockwise to the unlock position. Remove it. Use water to rinse it. If necessary, clean it with soap to remove all the dust.
Recommendation: It is suggested to clean the dust tank after each use.
Fig. 12

Filters
It is suggested to clean the filters regularly to ensure maximum efficiency. They can be cleaned with warm water. Dry them thoroughly before installing them back in the device. To take filters out:
Open the dust tank following the instructions on the before section.
Turn the metallic filter anticlockwise and remove it.
Fig. 13

Unscrew the plastic cyclone and remove it too.
Pull from the tab located on the top of the handheld vacuum cleaner and remove the high efficiency filter.
Wash all of them with warm water.
Allow them to dry completely before installing and using them again.
Fig. 14

Jalisco brush
Recommendation: It is important to clean the brush regularly to avoid hair and other foreign objects from tangling and to prevent blockages.
Press the brush release button on the bottom part of the suction base and remove the brush.
Wash it with warm water. Do not use detergents or soap.
Make sure it is completely dry before installing it back in the device.
Fig. 15

WET ACCESSORY

Before use
Take the product out of the box.
Remove all packaging materials. Keep the original box.
Make sure all the components are included and in good conditions, otherwise, contact immediately the official Technical Support Service of Cecotec.
When you do not use the vacuum cleaner for a long time, please remove the water tank and empty the remaining water. Do not expose it to direct sunlight or to damp environments.

Mop installation/removal, Removing/installing the water tank
Fig. 16
In order to install/remove the cleaning cloth you must first disassemble the water tank from the rest of the appliance.
In order to remove the water tank, use your foot to hold it against the ground and pull upwards until it unclicks from position.
Once the cloth has been installed and the water tank has been filled, to reinstall the water tank, simply push it back together until it clicks into position.
Note: Do not use cleaning agents. Use clean and room temperature water only. Do not use the vacuum cleaner to vacuum water.

Installing the mop cloth
Place the mop cloth on the ground with the Velcro facing upwards.
Align the mop cloth with the Velcro strips on the water tank and attach it.
Fig. 17

Water emission
Fig. 18
When using this product for the first time, make sure the water tank lid is not fully open. When not in use, pay attention to the water emission push button and to the tank lid, as water leak may occur when the water tank is full.
To activate water emission, the water emission push button must be pressed, and to stop water emission, the push button must be released as shown on the following figure:
Note : If the vacuum cleaner is not going to be used for a long period of time, make sure to remove the water tank and to empty the remaining water. Do not expose it to direct sunlight or to damp environments. Removing the mop cloth
To remove the mop cloth, just hold it with your hand and pull form it to detach it from the water tank.

Cleaning and maintenance /Cleaning the tank
To clean the water tank, fill the tank with clean water, shake it and then empty it.
The mop is washable; therefore, it is suggested to wash it after every use.
Replace the cloth after 20-30 uses, depending on the use.
When the mop cloth is used for a long time, it is possible that the water output is affected. This can be avoided by cleaning both cloth and water tank regularly.

TROUBLESHOOTING

Problem

| Possible reason|

Solution

---|---|---
The motor does not operate.| No battery.
The vacuuming tube, brush, battery, suction base or handheld vacuum cleaner are not assembled in place.| Charge the vacuum cleaner.
Check that the components and the handheld vacuum cleaner are assembled correctly.
Suction power level is very low.| The dust tank is full. Filters are dirty or blocked. Air inlet of the vacuuming tube or suction base are blocked.| Empty the dust tank. Clean or replace the filter. Clean the dirt attached to the brush.
The operating time after charging has decreased.| It has not been enough charged.
Battery is damaged or too old.| Charge the battery completely.
Replace the battery.

Note : For any further doubt, please contact the official Technical Support Service of Cecotec.

TECHNICAL SPECIFICATIONS

DISPOSAL OF OLD ELECTRICAL APPLIANCES

The European directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE), specifies that old household electrical appliances must not be disposed of with the normal unsorted municipal waste. Old appliances must be collected separately, in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation to dispose of the appliance correctly.
Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

TECHNICAL SUPPORT AND WARRANTY

This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.
The warranty will not cover the following situations:
The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
The product has been disassembled, modified, or repaired by persons, not authorised by the official Technical Support Service of Cecotec.
Faults deriving from the normal wear and tear of its parts, due to use.
The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.

With one click to the online shop

myRobotcenter.eu

|

myRobotcenter.co.uk

---|---

www.cecotec.es

Grupo Cecotec Innovaciones S. L. C/de la Pinadeta s/n, 46930 Quart de Poblet, Valencia, Spain

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>