motorola RM780 IMPRES Windporting Remote Speaker Microphone User Guide
- June 7, 2024
- Motorola
Table of Contents
- RSM Features
- Recommended Practice
- Attaching the RSM to the Radio
- Detaching the RSM from the Radio
- Cable Management
- Optional Accessories
- Replacement Parts
- Coil Cord Replacement Procedure
- Replacing the Dust Cover
- Attaching Swivel Clip
- Detaching Swivel Clip
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Motorola RM780 IMPRES Windporting Remote Speaker Microphone User Guide
Foreword
RF Energy Exposure and Product Safety Guide for Portable Two-way Radios
Attention!
Before using this accessory, read this guide which contains important
operating instructions for safe usage and RF energy awareness and control for
compliance with applicable standards and regulations. The Remote Speaker
Microphone (RSM), when attached to the radio, is restricted to occupational
use only to satisfy FCC/ICNIRP RF energy exposure requirements. Before using
this product, read the RF energy awareness information and operating
instructions in the Product Safety and RF Exposure booklet enclosed with your
radio to ensure compliance with RF energy exposure limits.
Acoustic Safety
Exposure to loud noises from any source for extended periods of time may
temporarily or permanently affect your hearing. The louder the volume of the
radio, the less time is required before your hearing can be affected.
Hearing damage from loud noise is sometimes undetectable at first and can have
a cumulative effect.
To protect your hearing:
- Use the lowest volume necessary to do your job.
- Turn up the volume only if you are in noisy surroundings.
- Turn down the volume before attaching headset or earpiece.
- Limit the amount of time you use headsets or earpieces at high volume.
- When using the radio without a headset or earpiece, do not place the speaker of the radio directly against your ear.
- If you experience hearing discomfort, ringing in your ears, or muffled speech, you should stop listening to your radio through your headset or earpiece, and have your hearing checked by your doctor. To change the volume level, refer to Radio Product Safety Leaflet or CPS for Surveillance extra loud (xL) Kit Configurations.
RSM Features
Recommended Practice
- Cover the audio jack with dust cover when it is not plugged with earpiece.
- Do not fill water into the audio jack.
- If water enters the audio jack, remove water by shaking the RSM.
Transmitting and Receiving
Recommended RSM Wearing Position
Attaching the RSM to the Radio
Attach the RSM connector to the side connector of the radio. Then secure the connection screw in a clockwise direction until tightened. Note: To ensure proper operation, turn off the radio before connecting the RSM to the radio. Connecting the RSM to the radio disables the speaker of the radio, but does not disable the microphone and PTT of the radio.
Detaching the RSM from the Radio
- Unscrew and detach the RSM connector from the radio side connector.
- Keep the dust cover inserted in the audio jack of the RSM when a secondary accessory is not being used.
Cable Management
To ensure optimum range and user experience, it is recommended to avoid crossing accessory cable with the radio antenna.
Optional Accessories
Replacement Parts
Service and Warranty
Motorola Solutions offers warranty for your accessory. Refer to your Motorola
Solutions dealer or point-of-purchase for detailed information.
NOTE: Warranty is void after customer replacement of any parts other than replacement parts listed.
Coil Cord Replacement Procedure
- Remove the screws to disassemble the RSM.
- Remove the cable.
- Reassemble the RSM.
![motorola RM780 IMPRES Windporting Remote Speaker Microphone User Guide
- Coil Cord Replacement Procedure](https://manuals.plus/wp- content/uploads/2021/09/motorola-RM780-IMPRES-Windporting-Remote-Speaker- Microphone-User-Guide-Coil-Cord-Replacement-Procedure.jpg)
Replacing the Dust Cover
-
Lift both sides of the dust cover.
-
Pull out the dust cover to dismantle it.
-
Bend the dust cover.
-
Insert to the dust cover slot.
Attaching Swivel Clip
- Match and align the arrowhead icons and side wings.
- Push down the top of the clip.
- Simultaneously, push slide clip upward.
Detaching Swivel Clip
- Push top of the clip to raise the clip to the highest position.
- Lift up the bottom release latch.
- Slide the clip to remove the clip.
Refer to manual MN006622A01for other languages: https://learning.motorolasolutions.com
https://learning.motorolasolutions.com/
Notes
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>