HDMI Splitter 1X4 By Single CAT User Manual
- June 7, 2024
- HDMI
Table of Contents
User Manual
HDMI Splitter 1X4 By Single CAT
Up TO 60m & Support 3D Full HD
Model No: AA6047
INTRODUCTION
Dear customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
Our series of HDMI Converters, switchers, extenders, matrixes and splitters are designed to make your A/V device use more convenient, more comfortable, more productive and more cost-efficient.
This extender can extend and connect one HD Source to four HD Displays or
Projectors by
four pieces of cat6/7 at the same time. The extending distance can reach 60m.
This extender meets the needs of multi-route and low-cost HD Signal long
distance transmission well.
Our devices offer solutions for noise, space and security concerns, data
center control, information distribution, conference room presentation, school
and corporate training
environments.
FEATURES
-
One HDMI input distribute and extend to found Display by four cat6/7 cable. The extend
distance can be up to 60m. -
Support 3D
-
Support video output : 24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
-
Audio format support : DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD
-
LED Status Light:the related led light will go bright.
-
The extend distance can be up to 60m.
-
Support signal retiming
-
No loss of quality
-
Installs in minutes
-
TX uses the DC5V/3A power adaptor.
-
Four RX: each one uses 5V/1A power adaptor
The accessories with the machines lists as picture:
- 5V/3A Power Adapter: 1 pcs
- 5V/1A Power Adapter: 4pcs
- one pc of Manual: 1 pcs
Output :output led status light
Input/EDID :HDMI input led status light
POWER: Power Led Status Light
EDID: The key for reading the EDID info
The steps to use the Switcher Key:
It can read the EDID info of the incompatible display and then adjust to
become compatible
with the display that does not work.
-
To connect the power adaptor with the power port of the HDMI 1X4 extender
-
To connect the HDMI output of the HDMI 1X4 extender with the HDMI input port of the display.
-
To keep the display at working status and choose the matched HDMI input port.
-
To press the Switcher key at the HDMI 1X4 extender and the EDID read action finished
while the "Input/EDID” LED light goes green. -
It reads the EDID info of the output connected four display one by one, the first time that
the light goes green means it is reading the EDID info of Output1 Display, the second time that the light goes green means it is reading the EDID info of the Output2 Display, the output 3 and output 4 follow this principle.(It suggests to use the Out1 for the DVI display when output channel have both DVI and HDMI display.) -
To take the HDMI cable out and power off with the HDMI 1X4 extender, it can use as
normal mode.
Note: It can use HDMI-DVI cable for DVI Monitor. The step is same as above.
Out1- Out4: RJ45 output interface
In: HDMI input interface
DC 5V: 5V DC-DC Power Interface
Figure 1.2 Front Panel Showing Picture
Figure 1.3 the rear and side board showing picture
HDMI OUT: Receiver to connect the HDTV or other display.
DC 5V: 5V DC-DC Power Adaptor Interface.
Operating and Connecting:
-
To use one piece of HDMI Cable to connect the HD Source with the HDMI input port of the extender, the HDMI Cable up to 15m.
-
To use one pieces of cat6/7 for each distributed HDMI Signal to connect the sender and
receive, the distance between the sender and receiver most up to 60m. -
To use one HDMI cable to connect the RX with the Display, The HDMI Cable length can be up to 20m.
-
To connect the attached powers at the receiver and sender.
SPECIFICATIONS:
Length of CAT-6 cable between Rx and TX…..…………….……….…….…….. up to 60m
HDMI Input…..………………..…24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
Support audio format input..DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD
HDMI Output…..…………………24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
Support audio format output……. ……………………LPCM7.1/DTS/Dolby-AC3/DSD
Max bandwidth…………………………….…….…………………………………225MHz
Max baud rate……………….…….…………………….………………………6.75Gbps
Input Video signal ………….………………………………………….… 0.5~1.5Volts p-p
Output DDC signal …………………………………………………… 5Volts p-p (TT1L)
Input HDMI cable distance..…… …………….….…≤15m AWG26 HDMI standard cable
Output HDMI cable distance………………….……≤20m AWG26 HDMI standard cable
Max working current(TX)………………………………………………………2000mA
Max working current(RX)…………………………………..……………………600mA
Power adapter format(TX).…Input:AC (50HZ, 60HZ) 100V-240V; Output: DC5V/3A
Power adapter format(RX)…Input:AC (50HZ, 60HZ) 100V-240V; Output: DC5V/1A
Operating Temperature range……..…..……………..…………………… (0 to +40℃)
Operating Humidity range…………….………..…….5 to 90%RH (No Condensation)
Dimension (TX) ……………………………………………..………..205x74x26(mm)
Dimension (RX) …………………………………..…………(82X44X22) (mm) X4pcs
Weight…..……………………………………..…..….……………………..……750g
.
Notes:
Please use the machine as the instruction listed to keep the long use lifetime
of the machine.
-
The machine should be placed at the spot far from the Damp, High-Temperature, Dusty,
Erosive, and oxidative environment. -
All parts will be free from the strong shake, hit, fall.
-
Touching the power adaptor with the wet hands is prohibited.
-
Please hold the power adaptor head and do not pull the power cord when cut off from the
socket. -
Please turn the power off when the machine is not used for long time.
-
Please do not open the cover and do not touch the inside parts.
-
Please use the original factory power adaptor.
Before power on, pls check the connection line carefully. And make sure that all interfaces are normally connected. The common trouble shooting way shows below:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>