PADO H20 Purewave Hydro Percussion Massager User Manual

PADO H20 Purewave Hydro Percussion Massager

CONTROL BUTTONS:

•  Percussion
•  Vibration
•  Speed increase (+)
•  Speed decrease (-)

LED COLOR:

• BATTERY INDICATOR
  LED color – White for 4 sections

• MODE INDICATOR
  LED color – White for Percussion mode
  LED color – White for Vibration mode

• SPEED INDICATOR
  LED color – White for all 7 sections

• CHARGING CRADLE
  LED color – White

CONTROLLING THE UNIT

Power is off

How to turn On unit?

| 1 second press of either the Percussion or Vibration mode button| Unit powers on and goes to lowest speed setting on either Vibration or Percussion mode.| Animation – At power ON, speed indicator bar should animate by illuminating the 1st section followed by the 2nd, 3rd, 4th, 5th, 6th & 7th. After all sections remain lit for 1 second, only the 1st section

should remain lit.

Power is on

How to turn Off unit?

| 1 second press of selected mode button| Unit powers off|
Power is on

How to switch modes?

| 1 second press of unselected mode button| Motor Turns OFF

Unit changes to the selected mode at Speed 1

| Animation – At power ON, speed indicator bar should animate by illuminating segment 1 followed by the 2nd, 3rd, 4th, 5th, 6th & 7th.

After all segments remain lit for 1

second, only the 1st segment should remain lit.

Power is on to unit

How to INCREASE speed?

| Momentary press of speed increase button| Speed increases to next higher speed. If speed is maximum, then no action taken|
Power is on to unit

How to DECREASE speed?

| Momentary press of speed decrease button| Speed decreases to next lower speed. If speed is minimum, then no action taken.|
 |  |  |

BATTERY STATUS

Battery status indicator lights up LED segments representing battery charge% (25 / 50 / 75 / 100)

Battery status LEDs remain on for 5 seconds after power on then turns off.

Unit is already ON|  |  | Battery status LEDs remain on for 5 seconds after any button is pressed, then turns off
Battery low (<10%)|  |  | Animation – If battery is <10%, 1st LED section of the battery status indicator will blink to let user know unit is low on battery & needs to be charged.
Unit is ON and battery is at 6V| Motor will turn off. After 5 seconds, unit will completely shut down.|  | Animation – 1st LED segment of the battery status indicator will blink for about 5 seconds to let user know battery is too low and needs to be charged.
Unit is OFF and battery is at 6V| Press and hold either Mode button

to turn on unit.

| Motor does not turn on.| Animation –1st LED segment of the battery status indicator will blink for about 5 seconds to let user

know battery is too low and needs to be charged.

 |  |  |

Massager CHARGING Status

battery is 25% or less, Segment 1 shall be solid and Segment 2 shall flash when battery voltage is greater than 25% but less than 50%. Segment 1 & 2 shall be solid and Segment 3 flashing while the battery voltage is less than 75% and greater than 50%. Segment 1, 2 and 3 shall be solid and Segment 4 will flash when the battery voltage is greater than 75% but less than 100%. All Segment shall be solid when the battery is

8.4V

Fully Charged| Check LED indicator on charger|  | ****

Animation – Segment 1-4 solid

Power is OFF Massager is charging| Press Vibration or Percussion Mode| No action|
 |  |  |

Dock CHARGING Status

Docking the massager

| Dock unit on charger while

massager is OFF

| -Charger begins to charge unit.| Animation – LED on charger should flash
Massager Docked and fully charged| Massager is docked and OFF| If unit is fully charged, LED indicator on charger should

remain solid

| Animation – LED should remain solid

FAULTS STATUS ON UNIT

and turn OFF
Overheated & unit is OFF| Motor Does NOT turn on when pressing Percussion or Vibration Mode| LEDs animate to let user know a fault has occurred.| Animation – ALL LEDs flash at 1Hz rep rate for 5 seconds and turn OFF
No-Fault| Massager operates normally|  |
 |  |  |

FCC regulatory conformance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference.

2.  This device must accept any interference received, including interference that may cause undesired operation.
   NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

3. Reorient or relocate the receiving antenna.

4.  Increase the separation between the equipment and receiver.

5. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

6. Consult the dealer or an experienced radio/TV technician for help
   NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B) and CAN RSS-216 / CNR-216. Current State Action Next State Notes Overheated while unit is ON Motor Turns OFF LEDS animate to let user know a fault has occurred. Animation – ALL LEDs flash at 1Hz rep rate for 5 seconds and turn  Overheated & unit is Motor Does NOT turn on when pressing Percussion or Vibration Mode LEDS animate to let user know a fault has occurred. Animation – ALL LEDs flash at 1Hz rep rate for 5 seconds and turn OFF No Fault Massager operates normally This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme à la norme CAN ICES-003 (B)/NMB-003 (B) et CAN RSS-216 / CNR-216. Cet appareil contient des émetteurs / récepteurs exempt (s) de licence qui sont conformes aux RSS exemptes de licence d’Innovation, Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes:
3. Cet appareil ne doit pas provoquer d’interférences.
4.  Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l’appareil.

RF Exposure

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d’ exposition aux rayonnements de la IC établies pour unenvironnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 20cm de distance d’un radiateur ou de votre corps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>