FITFIU GYM-100-Maquina Multiestacion Musculacion Instruction Manual

FITFIU GYM-100-Maquina Multiestacion Musculacion

INTRODUCTION

Thank you for selecting the FITFIU product.
The Multy-station home gym is constructed from heavy-duty, powder-coated tubular steel that is sure to stand the test of time and features large, non- slip rubber feet that will prevent unwanted movement. FITFIU maintains its reputation for quality with high-density cushioning and its choice of soft, sweat-proof materials. The leg, foot, and arm hold thick padding that offers support so you feel in complete comfort while you work out. The included cable attachments have rubber handles so you can maintain a firm grip no matter how heavy you chose to lift. We hope you will enjoy it and that this FITFIU product will fully meet your expectations.

IMPORTANT SAFETY INFORMATION

Before using this product, read all important safety information as well as the instructions manual. Please keep this manual in a safe place for future reference, and if you decide to sell this product, remember to give it to the new owner.

• Read and follow the instructions before setting up the unit, and using it. Safe use of the device can only be reached when it is properly assembled and used. it is your responsibility to ensure that all users of this device are informed regarding the warnings and precautionary measures.
• Use this product for its intended use only as described in this user manual. Do not use attachments not supplied or recommended by the manufacturer.
• Do not attempt any maintenance or adjustments other than those described in this user manual. Should any problems arise, discontinue use and consult an authorized service center or personnel.
• Do not use the unit outdoors.
• Keep children and pets away from the equipment while in use.
• Elderly or disabled users should only use the equipment in the presence of an adult who can provide assistance if required.
• Do not operate where aerosol (spray) products are in use or where adequate oxygen is not available.
• Keep dry – do not operate in wet or moist conditions.
• Keep the unit on a solid, level surface with a minimum safety area clearance of two meters around it. Be sure the area around the equipment remains clear of any obstructions during use.
• The equipment is for domestic household use only.
• One person only should use the equipment at a time.
• Wear comfortable and suitable clothing when using the equipment. Do not use the equipment barefoot or in socks. Always wear appropriate, enclosed athletic footwear. Never wear loose or baggy clothing as it can become caught on the equipment and create a hazard.
• Do not leave children unsupervised near or on the equipment.
• Children should not be allowed to play or operate the equipment at any time.
• This equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the equipment by a person responsible for their safety.
• Keep hands clear of all moving parts.
• Before using the equipment, check that all visible fasteners are sufficiently tightened and secure and that the cables are in the runners and in good condition.
• Handle or move the equipment with due care to avoid personal injury or damage to the equipment.
• Before using the equipment, stretch and warm up properly.
• Never operate the equipment if it is not functioning properly.
• This machine is only for indoors or for family. Users’ body maximum weight is 120kg. A person whose body weight exceeds this limit should not use this machine.
• Please always regularly that the safety chain guard that protects the moving parts of the machine is secured and in good order. Please make sure to keep 0.5m of free space around the equipment.
• This machine is only for domestic use.

ATTENTION:
Before beginning, this or any exercise program, consult your physician first. This is especially important for individuals over the age of 35 or persons with pre-existing health problems. Read all instructions before using we assume no responsibility for personal injury or property damage sustained by or through the use of this product.

NOTE:
FITFIU is not responsible or liable for any injury to the person or damage to property arising from the wrong use of the equipment.

ASSEMBLY

GENERAL SET-UP INFORMATION

• The assembly should be done by two adults if possible. Carefully read the manual and look at the explanatory drawing on the previous page before starting to set the item up.
• Remove all packaging material and spread all parts onto an even surface to get an overview and facilitate the assembly. Protect the set-up area ground by using any kind of cover.
• Check all parts listed in the parts list are included. Do not dispose of the packaging material until the assembly is completed.
• Note: When using tools a danger of injury exists. Use caution and keep the work environment as risk-free as possible. Dispose of foils or plastic bags that pose a choking hazard to children.

DESCRIPTION OF THE PRODUCT

DETAILED DESCRIPTION OF THE PRODUCT

2
3| Guide bar| 2| 43| Pulley bushings| 6
4| | | 44| Pulley| 12
5| | | 45| L” Bushing| 2
6| Upright| 1| 46| Plug 5025| 2
7| Pec mounting| 1| 47| Plug 3838| 3
8| Resistance bar| 1| 48| Plug 3838| 1
9| Handle| 2| 49| Plug 5050| 8
10| Pec arm right| 1| 50| Round plug Ø25| 4
11| Pec arm left| 1| 51| 5050 Foot end cap| 4
12| Foot bar| 1| 52| Foam roller| 4
13| Leg extension arm| 1| 53| Ø80245 Foam| 2
14| Rear base| 1| 54| Pin with ring| 1
15| Seat frame| 1| 55| Spiral chain| 2
16| Abdominal bar| 1| 56| Ø19 Steel bearing| 2
17| Low row bar| 1| 57| Ø16 Steel bearing| 4
18| Locking bar| 1| 58| Snap link| 5
19| Cross Pulley Bar| 1| 59| Nylon nut M16| 2
20| Pulley Plate| 2| 60| Nylon nut M10| 29
21| Pulley Rack| 2| 61| Nylon locking nut M8| 1
22| Front base| 1| 62| Ø16 Washer| 2
23| Nut cover| 2| 63| Hexagon socket M1025| 2
24| Flat plate| 2| 64| Washer Ø10| 62
25| Foam roller tube| 2| 65| Washer Ø8| 6
26| Upper shaft| 1| 66| Hexagonal bolt M1025| 6
27| Backrest pad| 1| 67| Hexagonal bolt M1075| 10
28| Seat pad| 1| 68| Hexagonal bolt M1070| 6
29| Arm cable| 1| 69| Hexagonal bolt M1065| 2
30| Chest cable| 1| 70| Hex bolt M1045| 9
31| Leg cable| 1| 71| Hex bolt M820| 2
32| Upper weight plate| 1| 72| Hexagonal bolt M845| 1
33| Weight plate| 9| 73| Hexagonal bolt M865| 4
34| Weight washer| 1| | |
35| Weight bushing| 1| | |
36| Weight pin| 1| | |
37| Weight selector bar| 1| | |
38| L-pin| 1| | |
39| Weight damper Ø6216| 2| | |
40| Plastic nut| 1| | |

NOTE:
The washer should be placed on both ends of all bolts (against the bolt head and against the nut) unless otherwise specified in these instructions. Hand- tighten all bolts on initial assembly and finally tighten with the spanner once the entire structure is erected.

Some parts may come pre-assembled from the factory.

INSTALLATION

STEP 1

1. Place the foot caps(#51) on the ends of the parts(#14,#22). Insert the plug 50*50(#49) into the part(#12).
2. Attach part(#3) to part(#14) using the hexagonal screw M1025(#63). Tighten the screw with a spanner. Attach part(#14,#24) to part(#2) using (2)hex bolts M1075(#67). Tighten the bolt with a spanner here.
3. Attach part (#12, #22) to part (#2) using (2) M10*75(#67) hex bolts.
4. Attach part (#6) to part (#2) using (2) M10*75(#67) hex bolts.

STEP 2

1. Slide the Ø62*16 weight buffer (#39) and the weight stack through the guide rods (#3) in succession.
   NOTE: Carefully slide the Weight Plates (#33) one by one onto the guide rods, do not lift more than you can safely control.

2. Place the weight bushing(#35) on the weight selector bar(#37) and fix it in the first hole of the weight selector bar(#37) using the weight pin(#36). Insert the Bar(#37) into the hole of the Weight Plates(#33). Slide the upper weight plate(#32) into the weight stack. Place the weight washer(#34) into the hole in the upper weight plate(#32). Insert the “L” pin(#38) through the bar(#37) to obtain the proper weight.

3. Attach part (#15,#23) to part (#6) using (2) M10*75(#67) hex bolts.

STEP 3

1. Insert the 50*50(#49) plugs into part(#1).
2. Attach part(#1) to part(#5) using (2) M10*75(#67) hex bolts.
3. Insert each of the guide rods (#4) into the holes in a part (#1), and then attach part (#1) to the guide rods (#4) using (2) M10*25 hex bolts (#66).
4. Insert the plug 3838(#47) into the part (#8). Place the cap(#48) on part(#8). Attach part(#8) to part(#5) using (2)Hex bolts M1070(#68).
5. Attach part(#18) to part(#8) using (1)Hex bolt M8*45(#72). Screw the plastic nut (#40) to part (#18).
6. Attach part(#21) to part(#5) using (2) M10*65(#69) hex bolts.

STEP 4

1. Insert the 5050(#49) plugs into part(#13). Attach part (#13) to part (#15) using (1) M1070(#68) hex screw. Insert the pin (#54) through the first hole of part (#15) and through part (#13) to lock part (#13). Next hole to release part (#13). Note: Tighten the bolt (#67) and loosen the nut enough for part (#13) to rotate freely.

STEP 5

1. Attach part (#28) to part (#15) using (2) M8*65 hex bolts (#73).
2. Insert the Ø25(#50) round plugs into part(#25). Insert part(#25) through part(#15,#13), and then slide the foam rollers(#52) over them.

STEP 6

1. Attach part (#27) to part (#5) using (2) M8*65 hex bolts (#73).

STEP 7

1. Insert the 5025(#46) plugs and 5050(#49) plugs into part (#7). Use a mallet to insert the shaft (#26) through part (#7) and through part (#1) until it is flush with both ends. Attach the shaft (#26) to part (#7) using (2) M8*20 hex screws (#71). You can rotate the part(#18), and then screw the plastic nut(#40) to lock the part(#7).
2. Put the “L” stops(#45) on the part(#7).
3. Insert the 38*38 plug (#47) into part (#10). Place the cap with hole (#42) into part (#10).
4. Attach part (#10) to part (#7) using (1) Nylon lock nut M16(#59) and (1) Washer Ø16(#62). When tightening the nut, make sure that part(#10) can rotate. Place the nut cap(#23) on the nut.
5. Slide the Ø80*245(#53) foam onto the part(#10). Hint: water or soap makes it easier.
6. Place the Comfort Grip(#41) on the part(#9,#10).
7. Attach part(#9) to part(#10) using (1)hex screw M10*25(#66).
8. Assemble the other Pec arm (#11) using the same method.

STEP 8
Once the machine is assembled, check if the cable is tensioned (At the correct tension, there should be a 3-5mm gap between the top plate and the weight stack).
If the cable is slightly loose, tighten it by tightening the bolt on top of the weight stack. If the cable is too loose, adjust the length of the spiral chain (#55), using the snap link (#58).

USING THE PRODUCT

Physical exercise, even at moderate intensity, will help to improve your health. Your blood pressure, cholesterol values, blood sugar, motivation, and even your mood may be greatly improved by doing some sports. You may tone your body within limits. Combining exercise with healthy nutrition may have a great impact on your body fat levels, your shape, and your overall well-being. Weight training improves your muscular fitness and your mobility and thus helps to reduce the risk of injuries.

ATTENTION: Make sure all bolts and nylon nuts are tightened enough before using the machine.

MAINTENANCE

• After the training, you should wipe the device and handles with a dry cloth. Thus, you avoid the components contaminated by dried sweat.
• The use of your Multi-Function Home Gym leads to natural wear and tear. This requires regular care and maintenance. Under normal conditions and use your Multi-Function Home Gym is maintenance-free. Nevertheless, the user is responsible for ensuring that all parts are regularly checked for tightness and performance-relevant wear.
• For cleaning do not use any aggressive cleaning agents but remove any dirt or dust with a soft or slightly damp cloth.
• Note: The performance of your Multi-Function Home Gym can be significantly reduced by the influence of environmental conditions.
• Any modification to the original parts, materials, or construction of the Multi-Function Home Gym can reduce performance significantly. The same applies in the case of severe contamination or misuse.
• This product is supplied with packaging to protect against damage during transport. The packaging materials are made from raw materials that are recyclable. Please dispose of these materials as required. if you wish to dispose of this product, please dispose of it according to current regulations. For more information regarding correct disposal, please contact the municipal office.

RECYCLING AND DISPOSING

When you decide to get rid of the machine, make sure to follow the local regulation. Protect the environment. Get rid of the machine taking care of the environment. Do not simply throw it away in the trash. Please separate plastic and steel to recycle. Package materials are recyclables. Please, throw them away in the appropriate trash can.

GUARANTEE

This product has a 2 years guarantee. This guarantee covers damages and bad function, only if the product has not been misused and all the instructions have been correctly followed. In order to claim your guarantee, you must present your receipt of purchase. The product has to be complete and has all its parts. The guarantee does not cover wear and tear, lack of maintenance, negligence, incorrect assembly, and inappropriate usage (blows, using the wrong power supply, storage, using conditions, etc). It is also excluded when nonoriginal or not-adequate assembly accessories or parts have been used on the product.

DECLARATION OF CONFORMITY (CE)

We, PRAT INTERNATIONAL BRANDS S.L., owner of the FITFIU Fitness brand, with registered office at c/Blanquers, 7-8 43800 – Valls, SPAIN, declare that the GYM-100 weight training machine, from serial number 2021 onwards, complies with the requirements of the applicable directives of the European Parliament and of the Council:

• Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonization of the laws of Member States relating to electromagnetic compatibility.

The delivered product corresponds to the specimen that has been submitted to the EC-type examination.

Harmonised standard :

• EN957-1:2005
• EN957-2:2003

Manual revisado en julio de 2021 www.fitfiu- fitness.com.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>