EXTECH HW30 Heat Watch User Manual
- June 6, 2024
- EXTECH
Table of Contents
EXTECH HW30 Heat Watch User Manual
Description
- Start/Stop
- Mode
- Recall
- Lap/Split
- LCD Display
Cautions
- This device is not a toy and must not reach children’s hands. It contains hazardous objects as well as small parts that the children could swallow. In case a child swallows any of them, please contact a physician immediately
- Do not leave the battery and packing material lying around unattended; they can be dangerous for children if they use them as toys
- In case the device is going to be unused for an extended period of time, remove the battery to prevent them from draining
- Expired or damaged batteries can cause cauterization on contact with the skin. Always, therefore, use suitable hand gloves in such cases
- See that the battery is not short-circuited. Do not throw the battery into a fire.
Battery Replacement
You, as the end user, are legally bound (Battery ordinance) to return all used batteries and accumulators; disposal in the household garbage is prohibited!
You can hand over your used batteries / accumulators, gratuitously, at the
collection points for our branches in your community or wherever batteries /
accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal
of the device at the end of its lifecycle.
Remove the screws from the back of the watch to open unit and battery compartment. The battery is a Round Button cell Type CR2032. Removing and replacing the battery will cause loss of all previous settings. Make sure the gasket seal is properly placed before replacing back cover and tightening screws.
Specifications
| Accuracy (Watch) | ±5 seconds/24 hours |
|---|---|
| Accuracy (RH) | ±5% (33 to 75% RH), ±7% (1 to 32% and 76 to 99%) |
| Accuracy (Temp) | ±3°F (1.5°C) |
| Temperature | 14 to 122°F (-10 to 50°C) |
| Resolution | 0.1/ 1o C or F |
| Update Rate | 5 seconds in Heat Index Mode, 2 minutes in other modes |
| Heat Index | 70 to 122°F (22 to 50°C) |
| Humidity | 1 to 99% RH |
| Memory | 30 Laps/ 30 Splits |
| LAP Counter | 99 Laps |
| Battery | CR2032 |
| Dimensions | 3.1×2.6×0.8 (79x66x23mm) |
| Weight | 3 oz. (85g) with battery |
OPERATION
Mode Selection
The HW30 Heat Watch has six different operating modes.
Press the MODE button to switch from one mode to another.
The HW30 will remain in the Heat Index mode for two minutes and then default
back to the clock mode.
Time Date Mode
The time date display shows current time, day of week, date and month. Also
displayed are the alarm and heat index alarm indicators when they are
activated.
Time and date set
Press and hold the RECALL button for 3 seconds to set time and date.
Press START to zero seconds.
Press LAP to select minutes, Press START to change minutes.
Press LAP to select hours, Press START to change hours.
Press LAP to select minutes, Press START to change minutes.
Press LAP to select year, Press START to change year.
Press LAP to select month, Press START to change month.
Press LAP to select date, Press START to change date.
Press LAP to select 12H/24H, Press START to change.
Press RECALL to exit time set mode.
The HW30 will return to display mode after 30 seconds of inactivity.
SETTING UNITS OF MEASURE
From heat index mode screen, Press LAP to change unit of measure (°F or °C).
HEAT INDEX MODE
In heat index mode the HW 30 displays relative humidity and ambient temperature (in °F or °C). Using these two readings, the HW30 also calculates and displays the Heat Index.
HEAT INDEX ALARM SET
The HW30 Heat Watch has a user settable heat index alarm. The Heat Watch will emit a 20 second audible warning when the heat index reaches the level previously set by the user.
To set the alarm
From heat index mode screen, Press and hold RECALL for 3 seconds
Press START to scroll up or LAP to scroll down
Press RECALL to save and exit setup mode, Or Press START if the alarm level
has already been set.
The alarm can be stopped by pressing any of the four buttons.
STOPWATCH LAP MODE
Before using be sure to reset stopwatch to 0.00.00.00.
The HW30 Heat Watch lap mode has advanced features that will make the timing
of events or training sessions easier and more enjoyable.
-
Lap Indicator The lap indicator flashes to indicate the lap in progress up to 99 laps.
When LAP is pushed, the lap indicator and lap time displays (top line of display) freeze for ten seconds before resuming and displaying next lap. Bottom display always shows cumulative time -
Fastest Lap/Slowest Lap/Average Lap Recall Once timing session is complete, press RECALL button to review fastest lap, slowest lap and average lap times. (based on 99 laps)
Then press START to review individual lap times. (30 laps) Lap times are shown on top line of the display.
Split times are shown on the bottom line of the display. -
Memory
The HW30 Heat Watch memory can store up to 30 lap (and split) times.
STOPWATCH SPLIT MODE
Before using be sure to reset stopwatch to .00.00.00.
The HW30 Heat Watch split mode has advanced features that will make the timing
of events or training sessions easier and more enjoyable.
-
Split time indicator When SPLIT is pushed the split indicator and split time displays (top line of display) freeze to indicate the current split time. Bottom display continues to always show cumulative time.
-
Fastest Lap/Slowest Lap/Average Lap Recall Once timing session is complete, press RECALL button to review fastest lap, slowest lap and average lap times. (based on 99 laps) Then press START to review split times. (30 splits)
Split times are shown on the bottom line of the display. Lap times are shown on top line of the display. -
Memory
The HW30 Heat Watch memory can store up to 30 split (and lap) times.
Timer MODE
The HW30 Heat Watch timer mode is a user programmable countdown timer. The
maximum count down time is 9 hours 59 minutes and 59 seconds. The minimum
settable time is 1 second. Press START to begin the countdown Press STOP to
stop the countdown The timer will count down for the selected duration.
The watch will emit an audible warning during the final 5 seconds of the
countdown.
The countdown will repeat itself until stopped by the user. The
countdown sequence will repeat itself and increment the timer count by one
each time it resumes.
The alarm can be stopped by pressing any of the buttons
ALARM MODE
The alarm will ring for 30 seconds.
Copyright © 2013-2020 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part
in any form ISO-9001 Certified
www.extech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>