QNAP QHora-301W Next Generation WiFi 6 Dual Port 10GbE SD-WAN Router Installation Guide
- June 6, 2024
- QNAP
Table of Contents
QHora-301W
Quick
Installation Guide
www.qnap.com
| 
---|---
LED Behavior
LED
| Status|
Description
---|---|---
1. Power| Green| The device is ready.
2. Status| Red| A system error occurred while powering on the device.
Flashes green|
- The firmware is updating.
- The device is restarting.
- The device is being initialized.
- The device is locating another device.
Green| The device is ready.
3.1 Gigabit Ethernet Port| Green| Port link established
Amber| WAN port link established
4. 10 Gigabit Ethernet Port| Green| Port link established
Amber| WAN port link established
5. Wi-Fi| Green| Wi-Fi link established
Flashes green| Press the WPS button for 3 seconds
|
---|---
Audio Alert
Duration| Frequency|
Description
---|---|---
Long and short beeps| 1 long and 2 short beeps| The router is
resetting configurations and rebooting (reset button).
2 long beeps and 1 short beep| The router has completed the firmware update.
Long beep| 1| The router is starting up.
Short beep| 10 (every 1 minute)| The CPU is overheating.
- Verify if the router is adequately ventilated and is placed in an open space. (Do not stack the router.)
- The alert stops once the temperature is below the threshold limit.
Download Center
www.qnap.com/download
Visit Download Center for our full guides and utilities.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and complies with the Class B digital device limits, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference cannot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by taking one of the following actions:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. RF
Modules installed
in this product must not be co-located or operating in conjunction with any
other antenna or transmitters, except when installed in accordance with FCC
multi-transmitter product guidelines.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
uncontrolled environments. This equipment must be installed and operated with
a minimum distance of 27cm between the radiator/antennas and the general
public
This device complies with CE compliance Class B.
CE Marking
The equipment described in this document faithfully complies with: European
Union Radio Equipment Directive (RED) 2014/53/EU. The Declaration of
Conformity is provided to customers with other technical documents upon
request and is accessible from https://www.qnap.com/en/contact-
us/ to authorized users. Radiation
exposure statement This equipment complies with radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 27 cm between the radiator and your body.
For operation within the 5.15 ~ 5.35GHz frequency range, it is restricted to
the indoor environment.
Hereby, QNAP Systems, Inc. declares that the radio equipment type QHora-301W
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.qnap.com
Data transmission is handled by software. Via software, it can define the
rule. When the equipment has no data to transmit, only the control frame will
be sent (like 802.11
management frame, such as beacon and probe Response). When failing to operate,
it will stop the service automatically
ISED Compliance Statement
Note: Industry Canada has been renamed Innovation, Science, and Economic
Development Canada (ISED) following the issue of RSP-100 Issue 11 and DC-01
Issue 06. Equipment certifications previously issued by Industry Canada remain
valid and do not require updating. Meaning you may see the names used
interchangeably in the documentation. The following statement is applicable to
ASiR-pRRH which has Innovation, Science and Economic Development (ISED)
approval: This device complies with ICES-003 of Industry Canada’s license-
exempt RSS. Operation is subject to the following two conditions
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
This product complies with IC radiation exposure limits set forth for an
uncontrolled environment. To comply with RSS 102 RF exposure compliance
requirements, a separation distance of at least 27 cm must be maintained
between the antenna of this device and all persons.
The device for the band 5150-5350 MHz is only for indoor usage to reduce the
potential for harmful interference to co-channel mobile satellite systems.
According to the requirement of the WEEE legislation, the following user
information is provided to customers for all branded QNAP Electronics products
subject to the WEEE directive.
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service, or the shop where you purchased the product.
RED 2014/53/EU Article 10 Compliance
RED 2014/53/EU requires that for products that could potentially have an issue
with a non-harmonized frequency in a specific EU country, the product
documentation must list the restrictions, and the packaging must carry a label
reflecting that country’s code.
AT
| BE| BG| HR| CY| CZ| DK
---|---|---|---|---|---|---
EE
| Fl| FR| DE| EL| HU|
IE
IT| LV| LT| LU| MT| NL|
PL
PT| RO| SK| SI| ES| SE|
UK
EU RoHS statement
This equipment complies with the European Union RoHS Directive 2011/65/EU on
the restriction of the use of certain hazardous substances in electrical and
electronic equipment.
The directive applies to the use of lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers
(PBDE) in electrical
and electronic equipment.
www.qnap.com
helpdesk.qnap.com
docs.qnap.com
Printed in China
P/N: 51000-024870-RS
References
- docs.qnap.com
- Customer Service - QNAP
- Contact Us | QNAP
- QNAP (US) | Experts in NAS, Networking, and Smart Surveillance
- Download Center | QNAP (US)