StarTech PEX1P2 1 Port PCI Express Dual Profile Parallel Adapter Card User Guide
- June 6, 2024
- StarTech
Table of Contents
Quick-Start Guide
Port PCI Express® Dual Profile Parallel Adapter Card – SPP/EPP/ECP
Product Diagram (PEX1P2)
Front Angle View
| Port | Function |
|---|---|
| 1 | Parallel Port |
| 2 | Bracket |
installations
3| PCIe x1 Connector| • Connect the Parallel Adapter Card to the PCI
Express Slot in the Computer
Requirements
For the latest requirements, please visit: www.startech.com/PEX1P2.
- Computer with an available PCI Express slot (x1)
Tools
- Small Phillips Head Screwdriver
Hardware Installation
Warning: Parallel Adapter Cards can be damaged by static electricity. Make sure that the Installer is properly grounded before they open the Computer Case or touch the Parallel Adapter Card. The Installer should wear an Anti-Static Strap when installing any computer component. If an Anti-Static Strap is not available, discharge any built-up static electricity by touching a large Grounded Metal Surface for several seconds. Only handle the Parallel Adapter Card by its edges and do not touch the gold connectors.
installing the Low Profile Bracket
By default, the Full Profile Bracket is attached to the Parallel Adapter Card. Depending on the system configuration it may be necessary to remove the Full Profile Bracket and replace it with the Low Profile Bracket (included).
- Using a Small Phillips Head Screwdriver, remove the two Bracket Screws securing the Full Profile Bracket to the Parallel Adapter Card.
- Align the Screw Holes on the Parallel Adapter Card with the Screw Holes on the Low Profile Bracket. Making sure the Parallel Adapter Card is sitting on top of the Screw Holes on the Low Profile Bracket.
- Insert the Bracket Screws through the Parallel Adapter Card and into the Screw Holes on the Low Profile Bracket.
- Using the Small Phillips Head Screwdriver, tighten the Bracket Screws, being careful not to over-tighten.
Installing the Parallel Adapter Card
-
Turn off the Computer and any Peripheral Devices that are connected (e.g. printers, external hard drives, etc.).
-
Unplug the Power Cable from the rear of the Computer and disconnect any Peripheral Devices that are connected.
-
Remove the Cover from the Computer Case.
Note: Consult the documentation that came with the Computer for details about how to do this safely. -
Locate an open PCI Express Slot (xl) and remove the corresponding Metal Cover Plate from the rear of the Computer Case. In most instances, the Metal Cover Plate is attached to the rear of the Computer Case with a single Save this Screw for the next step.
-
Gently insert the Parallel Adapter Card into the open PCI Express slot and fasten the bracket to the rear of the Computer Case using the Screw from step 4.
-
Place the Cover back onto the Computer Case.
-
Reconnect the Power Cable to the rear of the
-
Reconnect all of the Peripheral Devices that were disconnected in step
-
Connect an SPP/EPP/ECP Peripheral Device to the Parallel Port on the Parallel Adapter Card.
Software Installation
Driver Installation
You can download the latest drivers from the StarTech.com website:
www.startech.com/PEX1P2.
Navigate to the Drivers/Downloads tab to locate the Drivers. Follow
the instructions included with the Driver Files.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way
to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service by
StarTech.com, or an endorsement of the product(s) to which this manual applies
by the third-party company in question. StarTech.com hereby acknowledges that
all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained
in this manual and related documents are the property of their respective
holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United
States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP
(or their officers, directors, employees, or agents) for any damages (whether
direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceeds the actual price paid for
the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Safety Measures
• If the product has an exposed circuit board, do not touch the product under
power.
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada| StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
The U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom| FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
---|---|---|---