kogan KAMN27QUCMA 27 inch QHD IPS USB-C Freesync 75Hz Monitor User Guide
- June 6, 2024
- Kogan
Table of Contents
Kogan KAMN27QUCMA 27 inch QHD IPS USB-C Freesync 75Hz Monitor User Guide
SAFETY & WARNINGS
- Read all instructions before using the appliance and retain for reference.
- Unplug the monitor before cleaning it.
- Use a clean, slightly-dampened cloth to wipe the main monitor body.
- To clean the screen: turn it off, unplug it and wait for it to cool completely, then wipe it with a dry microfiber cloth.
- Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
- This monitor is designed with ventilation holes on the back of the casing. Do not cover or block them.
- Do not insert any object or spray any liquid into the vents.
- Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking adequate ventilation.
- Do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may injure nearby people.
- Unplug the monitor if it is not going to be used for an extended period.
- Do not place heavy objects on the monitor, its power cord or any connected cable.
- Do not open the back panel of the monitor, as it contains a high-voltage current even when not plugged in.
COMPONENTS
OVERVIEW
- Menu/Enter
- Volume/Down
- Brightness/Up
- Input select/Exit –
- Power On/Off
- LED indicator
- HDMI
- Display Port
- USB-C
- USB1
- USB2
- EARPHONE
- Power input (DC 24V)
STAND ASSEMBLY
Installing the Stand Base
- Clear a table and place a piece of soft cloth on it to prevent the LED monitor from being scratched.
- Lay the LED monitor flat on the table with the LED screen facing down.
- Insert stand into the monitor, then secure the base by tighten the screw.
- Stand the LED monitor up.
VESA MOUNT
Follow the steps below to install onto a monitor arm or wall mount (not included)
- Place the mounting plate onto the back of the LED monitor, lining up the holes of the plate with the holes in the back of the monitor.
- Insert the 4 screws into the holes and tighten.
- Assemble the mount as per the instructions provided with the mount.
- Connect the power and display cables to the monitor.
Note:
100 x 100mm VESA high hole (n=4), M4, pitch=0.7mm, screw mounting kit not included.
OPERATION
Before using the LED monitor
- Connect external equipment as per Setup below.
- Insert the power plug: the power LED indicator will glow orange, with no display input.
Setup
- Connect an HDMI, DisplayPort or USB Type-C cable from your monitor to the computer.
- Connect the adapter to a properly grounded AC outlet, then to the monitor.
- Power the computer on and then power the monitor on.
- Adjust the display settings on your computer if necessary.
Recommended resolution and refresh rate are 2560 x 1440 @60Hz.
USB-C Setup
This monitor supports the following simultaneous connections via USB Type-C:
- Display via DisplayPort™ 1.2 alternate mode
- Data via USB 3.1
- Power delivery (5.0V /3.0A, 9.0V /3.0A, 12.0V /3.0A, 15.0V /3.0A, 20.0V /2.25A, 20.0V /3.25A).
NOTE: Type-C is not supported on versions of Windows prior to Windows 10.
- Connect the USB Type-C cable from your monitor to the computer.
- Connect the adapter to a properly grounded AC outlet, then to the monitor.
- Power the computer on and then power the monitor on.
- Adjust the display settings on your computer if necessary.
Recommended resolution and refresh rate are 2560 x 1440 @60Hz.
Power On/Off
- Press the power button on the front of the monitor: the power LED indicator light will be blue when the LED monitor is on.
Using the OSD menu
- Use OSD menus to adjust settings by using the menu button on the front of the LED monitor.
Picture
Parameter
Brightness
Contrast
Sharpness
Aspect Ratio
Ultra Vivid
DCR (Dynamic Contrast Ratio
Range/Options
0-100
0-100
0-4
Between Full /16:9 / 4:3 / 5:4 / 1:1
Off/ Low/ Middle/ High
On / Off
Color
Parameter
Color Effect
Saturation
Gamma
Temperature
User mode color adjustments
Range/Options
Standard / FPS / RAC / RTS / Movie
0-100
Off I 1.8 / 2.0 / 2.2 / 2.4
6500 / 5400 I User/ 9300
R: 0-255
G: 0-255
B: 0-255
Advanced
Parameter
Volume
Mute
Overdrive
Adaptive Sync
Blue Light Reduction
Range/Options
0-100
On/ Off
On/ Off
On/ Off
Off I Low/ Middle / High
OSD
Parameter
Language
Menu Timeout
OSD HIV Position
Transparency
Reset
Range/Options
English / French / Deutsch / Italian / Spanish /
Russian / Dutch / Portuguese
10-60 seconds
0-100 (H = horizontal, V = vertical)
0-100 (0 = solid, 100 = transparent)
Restore factory defaults
SPECIFICATIONS
Panel — 27″
Power management — Normal, <30W (Typical), <110W (Maximum)
Standby mode: <0.5W
Off Mode: <0.5W
Displayable resolution — 2560×1440
Pixel dimension — 0.2331 (H) x 0.2331 (V)mm
Display color — 1.07B colors
Tilt — -5° – 37 ° Stand can up & down, 100mm, Swivel -45° – 45°
Active display area — 596.74(H) x 335.66(V)mm
Temperature — Operating: 5° – 40°
Storage: -20° – 60°
Power — DC24V5A
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head on line to help.kogan.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>