P PURLOVE WF309062 Upholstered Platform Bed Full with LED Installation Guide
- June 1, 2024
- P PURLOVE
Table of Contents
P PURLOVE WF309062 Upholstered Platform Bed Full with LED
Product Information
Specifications
- Model: WF309062/WF309064
- Capacity: 3L (WF309062) / 4L (WF309064)
- Part Lists : Refer to the manual for detailed part lists
- Hardware List : Refer to the manual for a detailed hardware list
- Usage : Ottoman bed frame
Product Usage Instructions
Assembly Instructions
- Follow the provided part list and hardware list to ensure all components are available.
- Start by assembling the headboard, footboard, slats, lift mechanisms, and side rails as per the manual.
- Use the specified bolts and tools to attach components securely.
- Ensure the bed frame is square by adjusting the foot end if needed.
Ottoman Operating Instructions
- Position the mattress on the slat frame in the closed position for correct operation.
- Apply force to initiate the ottoman movement; it gets easier as it nears closure.
- Check for even movement of the slat unit; adjust if necessary by moving the foot end slightly.
- Raise and lower the ottoman multiple times to lubricate the gas pistons after assembly.
Hardware Assembly Steps
- Fix the headboard legs to the headboard using specified bolts and washers.
- Attach the leg connecting plate to the head plate leg with a hexagon wrench.
- Secure the rear foot to the footboard using screws.
- Fix the angle iron to the footboard and connecting plate using the provided tools.
FAQ
- Q: What should I do if the ottoman does not operate correctly?
- A : Ensure a mattress is placed on the slat frame in the closed position for proper operation. Apply force gradually, and raise and lower the ottoman multiple times to lubricate the gas pistons.
- Q: How can I rectify the uneven movement of the slat unit?
- A : If the slat unit rubs unevenly, adjust the bed frame’s squareness by moving the foot end slightly to the left or right while keeping the head end stationary.
- Q: Can I tighten the screws before completing the entire installation?
- A: Avoid tightening screws before completing assembly. If you encounter difficulties, contact customer support for assistance.
ASSEMBLY INSTRUCTION
TIPS
- Please read the instructions fully before assembly. These instructions include important information that could ensure correct assembly. We have been working on providing high-quality products for you. However, in the rare instance that your product is defective, missing parts or there are some issues, please don’t hesitate to contact our customer service to submit parts requirements, assembly suggestions, or warranty claims, and we will give the best solution as soon as possible. If necessary, we need you to provide some more clear pictures of the issue.
- Insert the screws in holes and tighten thescrews, but not too tight, 70%~80% is ok, finally tighten all the screws. If some issues happen that some screws can not target tothe hole or some parts are difficult to install, please adjust the tightness of the screws.
- 3. 2 people are recommended to finish
DIMENSIONS
Part List
Hardware List
OTTOMAN OPERATING INSTRUCTIONS
IMPORTANT NOTICE
Once your bed frame is completely assembled, the slat unit will not operate correctly unless a mattress is placed on the seat frame. Position the mattress on the slat frame whilst it is in the closed position.
PLEASE NOTE – It takes a lot of force to make the initial movement of the ottoman. This is a design feature of the product so that it does not fall shut – the nearer to being closed the ottoman is, the easier it is to move. When the ottoman is almost shut, it will close completely under its own weight. When lowering the slat unit for the first time, take care to make sure it does not rub unevenly on the inside face of the side rails. If it does, the bed has been assembled slightly out of square. This can be rectified by moving the foot end of the bed slightly to the left or right whilst leaving the head end stationery.
PISTONS
The pistons used in the construction of this product are extremely strong and cannot be operated by hand when taken off the ottoman. All pistons are tested for correct pressure and operation before being attached to the slat unit. Initially, it might appear that the pistons are very stiff when opening and closing the ottoman.
THIS IS PERFECTLY NORMAL
When fully assembled and the mattress is in position, please raise and lower the ottoman 4/5 times toensure the gas piston are fully lubricated.
Attention : Do not tighten the screws before completing the entire installation.If you have any difficulty with the installation process, please feel free to contact us.
Step 1: Fix the Headboard legs(20L) / (20R) To the headboard(1) With Bolts (E) and Flat Washer (J) by using Allen key (K),you can choose the holes a and b or b and c .
Step 2:
Step 3:
Use an Allen wrench (K) to
connect the hinge (4) tothe side beams (3L) and(3R) at the headboard end with
M8 bolts (C) and plastic washers (L).
Step 4: nFix the Side Rails (3L)&(3R) to the Head board leg (20L)/(20R) and Footboard (2) with a hex wrench (K) and bolts (B).
Step 5:
Use a hex wrench (K) to connect the Reinforced Pipe (5) to the side member with bolts (A).
Step 6:
Stick the black non-woven fabric (19)To the bottom of bed.
Step 7:
Bottom view, when connecting 8 and 9, make sure that the holes in the dashed boxes are aligned.
Step 10:
Step 11:
LED light
If you can’t let the lights work successfully, please check the following:
- Please check the direction of the connect,try it in the opposite direction, according to the following picture.
- Please check the remote control,it needs you to tear down the plastic septum before use it.
- If one of the colors is not bright, please check whether the four wires in the plug are skewed, and move the main line to make the four wires flush
- Please check the direction of the arrow
- Please pull the plastic block out of the remote control
- Please check whether the four wires of the plug are neat
Operation Instructions of Controller
Specifications:
- Working temperature ：-20-60 ℃
- Supply voltage: DC12V
- Product size: L62xW35xH23mm
- Package size : L95xW68xH45mm
- Net weight: 42g
- Gross weight :57gOutput:
- Three CMOS drain – open output
- Connecting Mode： Common anodeMax load current A each color
Control Method:
Adopt IR remoter to control the led controller, which has 24buttons,the function of each button as the table below:
Panel specification and connecting drawing as follows:
Warning :
- The supply voltage of this product is DC12V and never connects to DC24V or AC220V.
- Never connect two wires directly in case of a short circuit
- The lead wire should be connected correctly according to the color that the connecting diagram offers.
- The warranty of this product is one year, in this period we guarantee replacement or repair with no charge, but exclude the artificial situation of damaged or overloaded working.
WARNING
THIS PRODUCT CONTAINS A BUTTON BATTERY
if swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours. Keep batteries out of reach of children. If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>