LUMME LU-FN100 Floor Fan User Manual
- June 12, 2024
- LUMME
Table of Contents
LUMME LU-FN100 Floor Fan
Product Information
The LU-FN100/ LU-FN101/ LU-FN102/ LU-FN104 is a fan produced by Cosmos Far
View International Limited. It is designed to provide cooling and air
circulation in various settings. The fan comes with multiple parts including a
front grille, blade cap, blades, rear grille nut, rear grille, motor shaft,
oscillating knob, motor, vertical adjustment screw, switch mode buttons,
screw, extension pole, out-joint, stand tube, stand cover, base, and fixation
hoop.
The actual set of parts may vary from what is listed in the user manual.
The fan operates on a power supply of 230V AC with a frequency of 50Hz. It has a power consumption of 50W. The net weight of the fan is 2.0 kg and the gross weight is 2.2 kg. The package size is 435mm x 175mm x 435mm.
Important Note: The warranty does not cover supplies such as filters, ceramic and non-stick coating, rubber seals, etc.
Product Usage Instructions
- Before using the appliance for the first time, read the user manual carefully and save it for future reference.
- Ensure the fan is connected to a power supply of 230V AC with a frequency of 50Hz.
- Cleaning and Maintenance:
- Always unplug the appliance before cleaning.
- Do not use chemical and abrasive cleaners for cleaning.
- For seasonal storage, use a carton to cover the fan.
- Loosen fittings and remove the front grille.
- Use a cloth soaked in soapy water to clean the fan blades. Do not immerse the appliance in water.
Parts list
- Front grille
- Blade cap
- Blades
- Rear grille nut
- Rear grille
- Motor shaft
- Oscillating knob
- Motor
- Vertical adjustment screw
- Switch mode buttons
- Screw
- Extension pole
- Out-joint
- Stand tube
- Stand cover
- Base
- Fixation hoop
Real set of the appliance could be different from listed in the User manual. Check once buy.
CAUTION
Read this manual carefully before using the appliance and save it for future
reference.
- Before the first use, check the device specifications and the power supply in your network. It is not intended for industrial use. For indoor use only. Use only for domestic purposes according to the instruction manual. Do not use with damaged cord, plug or other injuries. Keep the power cord away from sharp edges and hot surfaces.
- Do not pull the cord. Always take the socket. Do not reel the cord around the device housing. Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest customer service center. Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
- Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use. To avoid electric shock and fire, do not immerse in water or other liquids. If this occurs, immediately unplug it and contact service center for inspection. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not touch running parts of the fan. Keep foreign objects away from running parts and grille. Do not block air inlets on the motor block. Do not use the fan without protective grilles.
BEFORE THE FIRST USE
For packaging reasons the fan was delivered unassembled. Do not connect the
fan to the mains supply before you have completely finished the assembly.
Please take note of the following steps when assembling the fan. Tighten stand
tube to stand base with screw. Fix base cover to stand base with a screw.
Unscrew out-joint, put the stand cover and base cover on the stand base, pull
the extension pole out then tighten the out-joint again. Place control box
firmly on top of extension pole, tighten screw. Unscrew the blade cap by
turning clockwise and rear grill nut by turning counter clockwise and put both
blade cap and rear grill nut off the motor shaft. Put rear grille on motor
shaft. Secure it with rear grille nut. Slide blades on motor shaft so that
claws on motor shaft match the blades slots. Screw blade cap on shaft by
turning counter clockwise. Put front grille on rear grille and close clips or
screw grille ring to secure grilles together. Adjust the fan vertically by
vertical adjustment screw. The fan is ready for work
USING THE DEVICE
NOTE: Do not use the fan in wet conditions (for example rain) in order to
avoid electrical shocks.
- Always place the fan on a dry and even surface. To make the fan oscillate, push the oscillation button down; pull the button up to stop the oscillation. SPEED CONTROL To switch on the fan, simply press any of the speed control buttons:
- 1 – low airflow speed
- 2 – medium airflow speed
- 3 – high airflow speed
- 0 – off
CLEANING AND MAINTENANCE
Before cleaning, always unplug the appliance. Do not use chemical and abrasive
cleaners for cleaning. For seasonal storage use carton to cover the fan.
Loosen fittings and remove the front grille. Use a cloth soaked in soapy water
to the fan fans. Do not immerse the appliance in water.
SPECIFICATION
Power supply| Power| Net weight / Gross weight| Package size (L х W х H)| Producer:
Cosmos Far View International Limited
Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China Made in China
---|---|---|---|---
230 V ~ 50 Hz| 50 W| 2,0 kg / 2,2 kg| 435 mm х 175 mm х 435 mm
WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating,
rubber seals, etc.)
Production date is available in the serial number located on the
identification sticker on the gift box and/or on sticker on the device. The
serial number consists of 13 characters, the 4th and 5th characters indicate
the month, the 6th and 7th indicate the year of device production. Producer
may change the complete set, appearance, country of manufacture, warranty and
technical characteristics of the model without notice. Please check when
purchasing device.