KSR LIGHTING KSRFRD384 Multi Wattage Tilt Downlight Instruction Manual
- June 4, 2024
- KSR LIGHTING
Table of Contents
KSRFRD384 Multi Wattage Tilt Downlight
Instruction Manual
Available Rim Finishes: White, Chrome, Satin Chrome, or Black
WARNING:
Do not change the CCT or drive current of this downlight with the product
switched on, all changes must be done with the power off.
Installer Note:
To ensure a good connection strip back a minimum if 10mm insulation and push
the cable firmly into the terminal block.
Installation Sheet
Read these instructions before commencing installation. Please give these instructions to the owner/occupier after installation to retain for future reference/maintenance.
IP65 240V~50Hz 5W, 7W & 9W
Qr Quad CCT Fire Rated
Multi Wattage Tilt Downlight
Available Rim Finishes:
White, Chrome, Satin Chrome or Black
WARNING:
Do not change the CCT or drive current of this downlight with the product
switched on, all changes must be done with the power off.
Rim Size| Cut out| Void Depth Required| Beam Angle|
Dimmable| CCT| Lumen output per head
---|---|---|---|---|---|---
5W| 7W| 9W
85mm| 74mm| 90mm| 58′| Yes| 2700K| 5351m| 7001m| 8201m
3000K| 5401m| 7201m| 8451m
4000K| 5801m| 7851m| 9301m
6000K| 5901m| 7751m| 9101m
Fig. 3
Isolator Switch Isolates device from Circuit
Please Note: The isolation switch needs to be in the On ( I ) position during normal operation
Important Information
It is recommended that these luminaires are installed and fitted by a
qualified electrician ensuring the installation complies with current IEE
wiring regulations & local building control. These products are designed for
connection to a 240V~50Hz supply.
Any faulty, broken or damaged luminaires should be replaced immediately.
KSR will not accept responsibility for any claims arising from a poor
installation.
Please Note: The limited warranty shall be deemed null and void in the
following circumstances:
Failure by the installer, end user or any third party to exercise caution to
protect any covered product or part from outside damage, adverse temperature
(normal operating ambient temperature -10 ~ +35°C), humidity conditions,
fluctuations in the electrical system or physical abuse as well as failure
related to the workmanship in the installation of the products or parts.
Important User Advice
Always safely isolate the mains supply before installing/servicing.
This luminaire should not be fitted to damp or wet surfaces such as freshly
plastered or painted ceilings.
Do not use Megger or similar high voltage instruments without first switching
the isolation switch on the driver. To prevent damage to the driver, do not
mix with conventional magnetic ballasts on the same electrical circuit. At
the end of life the luminaire is classed as WEEE under directive 2014/30/EU
and should be disposed of in accordance with local legislation.
Installation Procedure
KSR recommends that a sample hole is cut in some scrap material to familiarise
yourself with the installation. Once you are completely satisfied: Locate the
area suitable to install these luminaires. Cut a 74mm round hole in the
ceiling and ensure sufficient ceiling void (Fig.1) without infringing on
joists, water pipes or electrical cables.
Connect the mains supply to the LED Driver (Blue – Neutral, Brown – Live).
Earth terminals are provided for earth continuity only. Press into place the
strain relief end cap by pushing down until it grips the outer cable
insulation. The LED driver allows for mains loop-in/loop-out connections, if
not looping through either of the L, E & N inputs can be used.
(Fig.2) Select the preferred color temperature by sliding the selector switch
located on the head to either 2700K, 3000K, 4000K, or 6000K. This must be done
before the power is switched on to the luminaire, changing the CCT while the
fitting is illuminated may damage the LED. Secondly select the preferred power
output located on the LED driver 5W, 7W and 9W.
Press springs back and pushes the luminaire body into the aperture.
If you are installing one of the KSR detachable rims remove the standard white
rim by twisting the rim anticlockwise, and remove the LED module from the rim
clockwise. Fit the new rim is a reversal of removal.
Important note: This downlight can not be covered with mineral wool
insulation, the head unit and driver should remain in free air space to avoid
overheating.
(Fig.3) This downlight is designed with an Isolator switch to allow for High voltage insulation resistance testing, without having to remove the luminaire/driver from the circuit. *Please note: Depending on the amount of Qr10 fittings on a circuit you may have to upgrade the breaker to a ‘C’ or ‘D’ type due to the way electronic LED drivers start up with higher inrush currents compared to halogen lighting. If dimming, see the recommended dimmers list at www.ksrlighting.com or for any other questions please call our sales office on 023 92 674343.
KSR Lighting Aftersales: 023 92 674343
E-mail:aftersales@ksrlighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>