ZEBRA ZT510 Industrial Router User Manual
- June 4, 2024
- ZEBRA
Table of Contents
ZEBRA ZT510 Industrial Router
Worldwide
Regulatory Information
All Zebra devices are designed to be compliant with the rules and regulations in locations they are sold and will be labeled as required. For more information about Zebra’s compliance with national and international mandates, go to: www.zebra.com/compliance For the latest version of this guide, go to: www.zebra.com/support Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s authority to operate the equipment.
End User License Agreement
For the complete End User License Agreement, go to
www.zebra.com/eula
Warranty
For the complete hardware product warranty statement, go to
www.zebra.com/warranty
United Kingdom
Statement of Compliance
Non-radio devices: Zebra hereby declares that this equipment is in compliance
with Electromagnetic Compatibility Regulations 2016, the Electrical Equipment
(Safety) Regulations 2016 and the Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment Regulations 2012. Radio
enabled devices: Zebra hereby declares that this equipment is in compliance
with the Radio Equipment Regulations 2017 and the Restriction of the Use of
Certain Hazardous Sub-stances in Electrical and Electronic Equipment
Regulations 2012. Any radio operation limitations within UK are identified in
Appendix A of UK Declaration of Conformity.
- The full text of the UK Declaration of Conformities is available at: www.zebra.com/doc.
- UK Importer: Zebra Technologies Europe Limited
- Address: Dukes Meadow, Millboard Rd, Bourne End, Bucking-ham shire, SL8 5XF
United States of America
FCC Compliance
This device complies with Part 15 rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to do one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced RF service technician for help.
IMPORTANT
- The radio must be installed with a minimum 20 cm separation between the user and the antenna.
- The radio must not be co-located or used in simultaneous transmitting condition with another radio.
- The host system shall have a label to indicate that the system contains a certified module.
- An example is “Contains FCC ID : XXXXX-XXXXXXXX , IC ID: XXXXX-XXXXXXXX”.
- The radio is for indoor use only in the 5150-5250 GHz frequency range.
The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables.
Product import ado pore Zebra México:
- IFT ID: ANC2101C00000330
- IFT ID: ANC2101C00000829
- IFT ID: ANC2101C00000331
- IFT ID: ANC2101C00001238
- IFT ID: ANC2101C00001652
- IFT ID: ANC2101C00000901
- IFT ID: ANC2101C00000694
- IFT ID: ANC2101C00001239
- IFT ID: ANC2101C00000902
Antenna Information
Type = Patch
- Gain = 3.66 dBi @ 2.4 GHz
- Gain = 3.19 dBi @ 5 GHz
- Impedance = 50 ohms
Type = Omni-directional
- Gain = 3 dBi @ 2.4 GHz
- Gain = 5 dBi @ 5 GHz
- Impedance = 50 ohms
WLAN specifications
802.11 b
- 2.4 GHz
- DSSS (DBPSK, DQPSK and CCK)
- RF power 17.77 dBm (EIRP)
802.11 g
- 2.4 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 18.61 dBm (EIRP)
802.11 n
- 2.4 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 18.62 dBm (EIRP)
802.11 a/n
- 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 17.89 dBm (EIRP)
802.11 ac
- 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 13.39 dBm (EIRP)
Bluetooth 4.1 + Low Energy (LE)
- 2.4 GHz
- FHSS(BDR/EDR), GFSK(Bluetooth Low Energy)
- RF power -0.85 dBm (EIRP)
Bluetooth Classic + Low Energy (LE)
- 2.4 GHz
- FHSS(BDR/EDR), DSSS (Bluetooth LE)
- RF power 9.22 dBm (EIRP)
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2022 Zebra Technologies Corp. and/or its affiliates. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>