CONNECTS2 CTSPG007.2 Peugeot Steering Wheel Control Interface Instruction Manual
- June 6, 2024
- Connects2
Table of Contents
V1. 05/18
CTSPG007.2
Peugeot Steering Wheel Control Interface
Vehicle Application
Peugeot 3008 2009>
Peugeot 807 2005 – 2014
Peugeot 407 2004 – 2010
Peugeot 207 2006 – 2012
Peugeot 308 2007>
Peugeot 307 2005 – 2008| Peugeot 607 2005 – 2012
Peugeot 208 2012>
Peugeot 5008 2009 – 2013
Peugeot RCZ* 2010>
Peugeot Partner 2008>
---|---
*Not Compatible with JBL Amplified Systems
Key Features
- Retains Steering Wheel Controls
- Retains Vehicle Settings Menu
- Provides Speed Pulse, Park Brake & Reverse Gear Outputs
ww.connects2.com
The information provided in this document is subject to change without notice
due to manufacturer changes and/or improvements to the product/s.
ABOUT THIS PRODUCT
CTSPG007.2
CAN-Bus Steering Wheel Control Interface for select Peugeot vehicles with
Blaupunkt/
Siemens VDO RD4 original stereo and Quadlock connector.
WIRING COLOUR CODES
Purple
Purple/Black
Green
Green/Black
Grey
Grey/Black
White
White/Black| Right Rear Speaker +
Right, Rear Speaker –
Left Rear Speaker +
Left Rear Speaker –
Right Front Speaker +
Right, Front Speaker –
Left Front Speaker +
Left Front Speaker –
---|---
Yellow
Black
Red
Pink
Green
Purple/White| Permanent 12V
Ground
Ignition 12V
Speed Pulse
Park Brake
Reverse Gear
---|---
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.
TECHNICAL SUPPORT
Connects2 Ltd. wants to provide a fast and suitable resolution to any problems encountered during the installation of this product. To get in touch with our dedicated technical support team, please fill in a ticket at support.connects2.com and provide as much information as possible.
FOLLOW US ON SOCIAL MEDIA for all the latest updates
| **|
---|---|---
/CONNECTS2
Watch us on YouTube| /CONNECTS2LT
lIKE US ON FACEBOOK| CONNECTS2LD**
Fallaw us on Instagram
| |
@CONNECTS2
Fallow us on Twitter| CONNECTS2LTD
Fallow us on Linkedin|
CONNECTS2BLOG.com
Follow our blog on WordPress
FITTING GUIDE
-
Remove and disconnect the original head unit.
-
Connect the 12-way Molex connector of the head unit patch lead (supplied separately) to the interface.
-
Connect the opposite end of the head unit patch leads to the head unit steering wheel control input on the back of the aftermarket head unit.
NB: This may be a 3.5mm jack plug or a wired input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
Important : This step must be completed before connecting power to the interface. Failure to so may result in no steering wheel control function.
-
Connect the 14 way Molex connector to the interface
-
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to “Wiring Colour Codes” on Pg. 2.
-
Connect the female vehicle-specific connectors on the harness to the male vehicle connector from the vehicle. Test head unit for correct operation.
STEERING WHEEL CONTROL FUNCTIONALITY
Peugeot
Citroen
If the vehicle you have
won’t let you change the selected item, please follow the steps below:
- Once in Menu Mode, hold the Source button for 3 Seconds
- After 3 seconds, the display will return to radio mode
- Use the roll wheel to change the value of the selected item
NB: Once power to the vehicle has been switched off, it will return to its
default settings
www.connects2.com