LAMAX D6769273 BCool Black Smart Watch Instruction Manual

: June 6, 2024
: LAMAX

Table of Contents

LAMAX D6769273 BCool Black Smart Watch
Operating Instructions
- Charging the watch
- Controls
Watch functions
Installing the mobile application and pairing the watch
Functions
Box contents
Technical specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LAMAX

LAMAX D6769273 BCool Black Smart Watch

Operating Instructions

Charging the watch

Fully recharge the watch before using it for the first time. Plug the included power cord into a USB charger or USB port on your computer, attach the pins to the tabs on the bottom of the watch, and attach the power cord to the watch with the magnets. The display shows the charging status information when the charger is connected. The entire battery will be charged in approximately 2 hours.

Controls

You can control the watch by moving your wrist or touching it. Turning your wrist to a horizontal position activates the watch display, showing the time and other information depending on the selected watch dial (e.g., number of steps, date, battery status, etc.). You can enable or disable the watch being activated by turning your wrist in the mobile application.
Control the following actions by pressing the side button or touching the watch display

Turning on the watch: Press and hold the side button.
Turning off the watch: Press and hold the side button, or on the lit display, swipe right to the watch menu, selecting the icon labelled “Settings” on the third page. Then touch the icon labelled “System.” A list will open where you should touch the icon labelled “Off” and confirm the selection by touching the green button.
Turning on the display: Press the side button or turn your wrist to a horizontal position.
Navigating: Swipe right or left on the screen or up and down if there is a list.
Status bar and quick settings: Swipe your finger from top to bottom on the screen while the dial is displayed.
Confirm selection: Touch the screen.
Return: Press the side key.

Watch functions

Time
Date
Weather
Sleep monitor
Phone search
Pedometer
Calories burnt
Heart rate
Camera remote control
Music remote control
Sport activities
Games
Ability to change and load your own dials from the application
Relaxation (Breathing exercises) – Alarm clock
Stopwatch
Timer
Do not disturb
Drink and activity alert
Incoming call notification and reject call
Incoming message and phone notifications

Installing the mobile application and pairing the watch

The watch is compatible with iOS (10 and higher) and Android (5.1 and higher). Download the mobile app to control your watch at the link below:

https://www.lamax-electronics.com/downloads/lamax-bcool/app/

Turn on Bluetooth and location services on your smartphone. Turn on your watch. In the app, click the button to connect the device, select the name „HLAMAXBCool-xxx“ and then confirm the selection in the dialog box. On iOS mobile phones, you will also need to confirm the pairing and allow all notifica-tions from this phone to be displayed.
If the watch is not paired or disconnected, the icon will be displayed in the status bar . After pairing, the icon changes to .

Functions

Heart rate monitoring
By default, continuous heart rate monitoring is turned on, which measures your heart rate at regular intervals. The results and history of continuous measurement can be displayed in the application, where it can also be turned off. You can also use the manual heart rate measurement function in the watch. This measurement can be activated by selecting the „Heart rate“ fun-ction in the watch menu. After selecting this function, the measured result is displayed after a few seconds.

Monitoring physical activity
Steps are recorded automatically as soon as the watch is switched on. Based on the obtained data, it then calculates the distance travelled, the time spent moving and the calories burnt. This data can be displayed in summary in the „Daily activity“ function in the watch menu. The measurement history is available in the application.

Sleep monitoring
The watch automatically detects the beginning and end of your period of sleep. The last measured value can be displayed in the watch in the menu under the „Sleep“ function. The history of these measurements can be viewed in the application.

Alarm clock
In the device settings of the app, go to „Alarm clock settings“. Select the alarm time and the days on which the alarm should be active. At the selected time, an alarm clock icon will appear on the watch and the watch will vibrate. Touch the screen or press the side button to stop the alarm.

Inactivity alert
In the device settings of the app, go to „Session settings“ / „Session notification“ and set the start and end of the time interval when the watch should prompt you for activity. If you are motionless for a long time during this period, the watch will vibrate and a warning will appear on the display

Find my phone
Select the „Find phone“ function in the watch menu. Touch the icon to turn the function on. The phone then rings and vibrates. If the phone does not respond after turning on the function, it does not support this function.

Phone camera remote control
In the device settings of the app, go to „Camera controls“ „Change photo“. Confirm your selection and turn your wrist to take the photo. After the pho-to has been successfully taken, a confirmation message will appear on the phone display.

Displaying weather information
After synchronizing the watch with the app, the day’s weather information is displayed under the „Weather“ function.

To view notifications for incoming calls and messages
In the app, go to „Notifications“ in the watch settings. Select which notifications you want to appear on the watch display. These notifications can be displayed in the watch in the menu under the „Messages“ function. If you do not receive a notification on the watch even after switching it on, your phone does not support this feature.

Changing the dial
On the displayed dial, touch and hold the watch screen to display a selection of other dials. Additional dials can be downloaded from the app after pairing with the watch.

Do not disturb mode
When “do not disturb” mode is on, the watch does not alert you to phone notifications. This mode can be turned on from the status bar (month icon) or in the watch settings.

Water and dust resistance
The watch is resistant to the ingress of water and foreign objects according to the degree of protection IP68. This means that it is protected against immersion in water for 30 minutes to a depth of 1.5 metres and against the ingress of foreign objects, including dust.
Warning: Never charge a wet watch. The device is not intended for use during water sports, swimming, diving or showering. It must not be exposed to pressurized water or strong water jets, such as rapid immersion or diving.

Box contents

Watch with a multicoloured strap
Monochrome strap
Magnetic charging cable
Manual

Technical specifications

Bluetooth version: 5.0
Display: 1.4“ IPS colour display
Watch body weight: 19 g
Total watch weight: 34 g
Watch body dimensions: 36.5 mm x 40.9 mm x 11 mm
Charging: USB5 V / 0.5–1 A
Battery: 160 mAh Lithium-ion (approx. 5-7 days of normal use)
Water resistance: According to IP68: up to 1.5 metres for 30 minutes
Compatibility: Mobile devices with iOS 10+ and Android 5.1+ *

*Android skins from some manufacturers may cause problems with connecting Bluetooth devices. Current exceptions can be found at https://www.lamax-electronics.com/bcool-compatibility/.

The most current version of the manual can be found under this link:

https://www.lamax-electronics.com/downloads/lamax- bcool/manual/LAMAX_BCool_manual.pdf