SW-MOTECH BC.HTA.05.740.30300 Saddlebag Set Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.05.740.30300 Saddlebag Set
Mounting Instructions
ATTENTION: The assembly of this product can be complicated and requires a
good technical understanding. If you are not sure of how to do this, have a
specialty garage perform the mounting and service.
SW-MOTECH accepts no liability for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW-
MOTECH, should be tightened to the torque specified in the OEM maintenance
manual for your motorcycle. If no torque specifications are provided in the
OEM maintenance manual, the following torques may be used:
**MS 23 Nm**
All screws, bolts and nuts should be checked after driving the first 50 km to
ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to
secure all screws, bolts and nuts.
Subject to change. Not responsible for typos
Accessories
Mounting
**STEP 1 **Attach the shown parts on the mounting brackets (1).
The shown buckles will come with your panniers.
Attach them as shown.
Tighten screws (4) after attaching the panniers. Please pay attention to the
information sheet included to the panniers.
**STEP 2 **Mount the parts as shown.
Make sure the engraving of the panniers frames (9) is located on the side of
the clips (as shown in the drawing).
Make sure the panniers frames (9) fits proper after tightening the screws
(11).
**STEP 3 **Attach the mounting brackets (1) on the passenger footrests as shown.
Use liquid thread locker to secure the screws.
**STEP 4 **Pay attention to the audible clicking sound.
Before riding check the proper fit of the panniers frames.
MOUNTING INSTRUCTIONS
Art.-Nr. / Item No.: **BC.HTA.00.740.3000*** & **BC.HTA.00.740.3100***
PRO BLAZE® saddlebags
PRO BLAZE® saddlebags high version
Thank you for choosing this premium product from SW-MOTECH.
Please visit ourwebshop for additional information, such as application charts
and PDF mounting instructions. Any other documents that may be required (e.g.
ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TOV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: After fixation also make sure that no moving parts are
obstructed and the function of the vehicle is not hindered in any way. Lamps
as taillight and turn signals must not be limited in their function. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
ATTENTION: Compatibility with accessory exhaust systems cannot be
guaranteed!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream. For this reason compress the
suspension fully several times with your vehicle stationary.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance! Cornering and ground clearance can be reduced by using
this product!
ATTENTION: Modifications will void any warranty.
ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
**⚠ ATTENTION**
NOT FOR OFFROAD-USE!
PARTS LIST
Step| No.| Item No. / Description a| Part| Quantity
b| N.m c
---|---|---|---|---|---
| (1)| BC.HTA.00.470.3000| PRO BLAZE Saddlebags| |
(3)| BC.ZUB.00.019.3000| Buckle| 2/2|
| | LSF.350.250| Protection Foil; 250 x 350 mm| 2/2|
| | | | |
| (3)| BC.HTA.00.740.901.01 / 902.01| Saddlebag; left/ right| 2/2|
| | | | |
| (4)| BC.ZU B.00.064.30000| Waterproof innerbag| 2/2|
| | PRO BLAZE Satteltaschen hohe Version| PRO BLAZE Saddlebags high
version| |
| (1)| BC.ZUB.00.019.3000*| Buckle| 2/2|
(3)| LSF.350.250| Protection Foil; 250 x 350 mm| 2/2|
| | | | |
| (3)| BC.HTA.00. 740. 901.02 / 902.02| Saddlebag; left/ right| 2/2|
| | | | |
| (4)| BC.ZU B.00.064.30000| Waterproof lnnerbag| 2/2|
Note: a All measurements in millimeters. b The second number indicates the
total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle
manufacturer! The standard torque in this table can be used as long as it is
within the vehicle manufacturer’s specifications.
FASTENING
After mounting the saddlebags frames you need to protect the surface of the
motorcycle against scratches with the included protection foil (2).
Clean the surface from grease and dirt before applying the protection film.
ATTENTION: Sharp edges have to be covered with several layers of the
protection foil!
After mounting the saddle bags, check if the affected parts of the vehicle are
sufficiently protected against abrasion.
Slide the pannier sleeves of the saddlebags (3) on both sides onto the
mounted support arms.
Fasten the saddlebags (3) with the velcro flaps over the rear (passenger seat)
of the motorcycle, as shown in the drawing.
ATTENTION: Make sure after loading the saddlebags (3) there is NO weight
on the saddlebags frames!
The weight of the saddlebags (3) must be supported by the velcro flaps,
NEVER by the saddlebags frames.
**After loading, the saddlebags frames must be positioned in the saddlebags
sleeves, as shown in the detail drawing!
**_
ATTENTION: Pay attention to the mounting instructions included to the
saddlebags support arms!
Fix the saddlebags [3] with the safety straps to the loosely mounted buckles
[1] on both sides. Then tighten the screws of the buckles [1] as described in
the mounting instructions of the saddlebags support arms.
Tighten the safety straps to secure the saddlebags (31).
ATTENTION: Make sure BEFORE each ride that the velcro flaps and safety
straps of the saddlebags (3) are firmly tightened and there is NO weight on
the support arms!
Wrong mounted saddlebags (3) can damaged the product and vehicle!
Finally roll up the excess salty strap length and secure it.
Use the waterproof inner bags (4] to protect your luggage from moisture.
Additionally protect sensitive luggage [e.g., electronic equipment] from
moisture with a plastic bag.
SAFETY, LOADING AND CARE
SAFETY AND LOADING: Make sure weight is evenly distributed between the
sagglebags. Make sure that the loading is secured against shifting during the
ride!
Do not store sharp or fragile objects!
ONLY loop assigned SW-MOTECH products to the MOLLE attachment!
ATTENTION: Remove the support arms when driving WITHOUT saddlebags from the
vehicle!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream.
ATTENTION: Compatibility with accessory exhaust systems cannot be
guaranteed!
CARE: For cleaning use ONLY a soft textile brush, cloth or sponge and
warm soapy water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the product after riding in salty conditions, to avoid damage from salt.
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10 – 35282 Rauschenberg
Germany
Tel. +49 (0) 64 25/8 16 8-050 · Fax +49 (0) 64 25/8 16 8-10
info@sw-motech.com – www.sw-
motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>